sensor TOYOTA SEQUOIA 2001 Service Repair Manual

RS0UY±05
H24698
Seat Position
Sensor
Assembly
Seat RailFeeler
Gauge Seat Position Sensor
Assembly Protector
1 mm
(0.039 in.)
RS±108
± SUPPLEMENTAL RESTRAINT SYSTEMSEAT POSITION SENSOR ASSEMBLY
3391 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the seat position sensor assembly in-
volved in a collision when the airbag has deployed.

If the seat position sensor assembly center has been
dropped, or there are any cracks, dents or other de-
fects in the case, bracket or connector, replace it with
a new one.

When installing the seat position sensor assembly
center, be careful that the SRS wiring does not inter-
fere with other parts and that it is not pinched be-
tween other parts.

After installing, shake the seat position sensor as-
sembly to check that there is no looseness.
1. INSTALL SEAT POSITION SENSOR ASSEMBLY
(a) Using a feeler gauge 1 mm (0.039 in.), install the seat
position sensor assembly.
HINT:
Be sure that a clearance between the seat position sensor as-
sembly and the seat rail is between 0.6 mm (0.023 in.) and 2 mm
(0.079 in.).
(b) Using a torx
) socket wrench, tighten the torx) screw to
install the seat position sensor assembly.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
(c) Make sure that a clearance between the seat position
sensor assembly and the seat rail is between 0.6 mm
(0.023 in.) and 2 mm (0.079 in.).
(d) Connect the connector to the seat position sensor assem-
bly.
2. INSTALL SEAT POSITION SENSOR ASSEMBLY PRO-
TECTOR
Install the seat position sensor assembly protector to the seat
position sensor assembly.
3. Separate type (Power adjuster):
INSTALL SEAT CUSHION LOWER SHIELD, SEAT
CUSHION OUTER SHIELD AND SEAT CUSHION IN-
NER SHIELD (SEE PAGE BO±117)
4. Separate type (Power adjuster):
INSTALL SLIDE KNOB AND RECLINING KNOB
(SEE PAGE BO±117)
5. Separate type (Power adjuster):
INSTALL FRONT SEAT ASSEMBLY LH
(SEE PAGE BO±123)

± SUPPLEMENTAL RESTRAINT SYSTEMSEAT POSITION SENSOR ASSEMBLY
RS±109
3392 Author: Date:
2005 SEQUOIA (RM1146U)
6. Separate type (Manual adjuster):
INSTALL SEAT CUSHION OUTER SHIELD
(SEE PAGE BO±130)
7. Separate type (Manual adjuster):
INSTALL VERTICAL ADJUSTER HANDLE
(SEE PAGE BO±130)
8. Separate type (Manual adjuster):
INSTALL FRONT SEAT ASSEMBLY LH
(SEE PAGE BO±134)
9. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
10. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
11. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

RS0UY±06
H23939
RS±114
± SUPPLEMENTAL RESTRAINT SYSTEMOCCUPANT CLASSIFICATION ECU
3397 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the occupant classification ECU in-
volved in a collision when the airbag has deployed.

If the occupant classification ECU center has been
dropped, or there are any cracks, dents or other de-
fects in the case, bracket or connector, replace it with
a new one.

When installing the seat position sensor assembly
center, be careful that the SRS wiring does not inter-
fere with other parts and that it is not pinched be-
tween other parts.
1. INSTALL OCCUPANT CLASSIFICATION ECU
(a) Install the occupant classification ECU.
(b) Connect the 2 connectors to the occupant classification
ECU.
2. INSTALL FRONT SEAT ASSEMBLY RH
(SEE PAGE BO±123)
3. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
4. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
5. INITIALIZE OCCUPANT CLASSIFICATION ECU
(SEE PAGE DI±1137)
6. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

RS0BU±10
H23906
Front Airbag Sensor (LH)Front Airbag
Sensor (RH)Front Passenger
Airbag Assembly (RH)
Seat Belt
Pretensioner (RH)
Airbag Sensor Assembly Seat Belt Pretensioner (LH) Spiral CableCurtain Shield
Airbag Assembly (RH)
Side Airbag
Assembly (RH) (*1)
Side Airbag Sensor
Assembly (RH) (*1)
Side Airbag Assembly (LH) (*1) Side Airbag Sensor
Assembly (LH) (*1)
Curtain Shield Airbag
Assembly (LH) (*1)
Combination Meter
(Warning Light)
Steering Wheel Pad
(With Airbag)
Curtain Shield Airbag
Sensor Assembly (LH) (*1)
Curtain Shield Airbag
Sensor Assembly
(RH) (*1)RSCA OFF
Switch (*1)
Occupant Classification
ECU (*1)
(*1) w/ Side Airbag and Curtain Shield Airbag
± SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
RS±119
3402 Author: Date:
2005 SEQUOIA (RM1146U)
WIRE HARNESS AND CONNECTOR
LOCATION

RS0BV±08
RS±120
± SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
3403 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
HINT:
The SRS wire harness is integrated with the cowl wire harness assembly. The wires for the SRS wire harness
are encased in a yellow corrugated tube and all the connectors in the system except the seat position airbag
sensor connector and occupant classification ECU connectors, colored are yellow.
1. VEHICLE NOT INVOLVED IN COLLISION
Perform a diagnostic system check (see page DI±1147).
2. VEHICLE INVOLVED IN COLLISION
(a) Perform a diagnostic system check (see page DI±1147).
(b) Check breaks in all wires of the SRS wire harness, and exposed conductors.
(c) Check if the SRS wire harness connectors are cracked or chipped.

BE±8
± BODY ELECTRICALTROUBLESHOOTING
3412 Author: Date:
2005 SEQUOIA (RM1146U)
DEFOGGER SYSTEM
SymptomSuspect AreaSee page
Rear window defogger does not operate.
1. HTR Fuse
2. DEFOG Fuse
3. DEFOG Relay
4. Defogger Switch (in A/C Panel Switch)
5. Defogger Wire
6. Wire HarnessBE±14
BE±14
BE±14
BE±65
BE±65
±
Mirror defogger does not operate.
1. MIR±HTR Fuse
2. HTR Fuse
3. Mirror Heater Relay
4. Mirror Heater
5. Wire HarnessBE±14
BE±14
BE±65
BE±65
±
POWER WINDOW CONTROL SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
All the power windows do not operate.
(Power door lock system is normal.)
1. POWER MAIN Relay
2. Driver Door ECU (Power Window Master Switch)
3. Body ECU
4. Wire HarnessBE±69
DI±1788
±
±
Only the driver's window does not operate.
1. Power Window Motor
2. Power Window Pulse Sensor Circuit
3. Power Window Limit Switch Circuit
4. Driver Door ECU (Power Window Master Switch)BE±69
DI±1803
DI±1800
±
ºWindow lock functionº does not operate.Driver Door ECU (Power Window Master Switch)BE±69
Only the rear LH window does not operate.
1. Power Window Motor
2. Power Window Switch
3. Body ECUBE±69
BE±69
±
Only the rear RH window does not operate.
1. Power Window Motor
2. Power Window Switch
3. Body ECUBE±69
BE±69
±
Only the front passenger's window does not operate.
1. Power Window Motor
2. Power Window Pulse Sensor Circuit
3. Power Window Limit Switch Circuit
4. Passenger Door ECUBE±69
DI±1841
DI±1838
±
The Key related power window operations do not operate with
driver side door key cylinder.
(Master switch operation is normal.)1. Door Key Lock and Unlock Switch Circuit
2. Driver Door ECU (Power Window Master Switch)DI±1791
±
º Auto up º or º Auto down º does not operate. *1
1. Power Window Pulse Sensor Circuit
2. Power Window Limit Switch Circuit
3. Driver Door ECU (Power Window Master Switch)DI±1803
DI±1800
±
*1: º Auto up º or º Auto down º may not function when the manual switch is pressed and held for 2 sec. or
more with the window glass fully open or closed. In this case, by performing a sequence of the window glass
operations (full open, fully close and then half open), the function can be restored. If not, replace the driver
door ECU or passenger door ECU.

± BODY ELECTRICALTROUBLESHOOTING
BE±9
3413 Author: Date:
2005 SEQUOIA (RM1146U)
POWER DOOR LOCK CONTROL SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
All the doors cannot be locked or unlocked.
(Power window control system is normal.)1. Door Unlock Detection Switch
2. Door Key Lock and Unlock Switch
3. Driver Door ECUBE±79
BE±79
±
Only one back lock control does not operate.
1. Back Door Lock Motor
2. Back Door Unlock Detection Switch
3. Back Door Key Lock and Unlock Switch
4. Back Door ECUBE±79
BE±79
BE±79
±
Driver door key related function does not operate.1. Door Key Lock and Unlock Switch
2. Driver Door ECUBE±79
±
Front passenger door key related function does not operate.1. Door Key Lock and Unlock Switch
2. Passenger Door ECUBE±79
±
Back door key related function does not operate.1. Door Key Lock and Unlock Switch
2. Back Door ECUBE±79
±
THEFT DETERRENT SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
The theft deterrent system cannot be set.
1. Key Unlock Warning Switch Circuit
2. Door Unlock Detection Switch Circuit (Driver Door ECU)
Door Unlock Detection Switch Circuit (Passenger Door
ECU)
Door Unlock Detection Switch Circuit (Back Door ECU)
Door Unlock Detection Switch Circuit (Body ECU)
3. Engine Hood Courtesy Switch Circuit
4. Back Door Courtesy Light Switch
5. Courtesy Light Switch Circuit
6. Glass Breakage Sensor Circuit (*1)
7. Body ECUDI±1715
DI±1791
DI±1829
DI±1869
DI±1723
DI±1725
DI±1864
DI±1728
DI±1774
±
The system cannot be canceled when the ignition switch is turned
ON with a key.
1. AM1 Fuse
2. AM2 Fuse
3. Key Unlock Warning Switch Circuit
4. Ignition Switch
5. Body ECUBE±14
BE±14
DI±1715
BE±24
±
The system cannot be canceled when the back door is unlocked
with a key.
1. Back Door Unlock Detection Switch Circuit
2. Back Door Key Lock and Unlock Switch Circuit
3. Back door ECU
4. Body ECUDI±1869
DI±1882
±
±
The system does not operate when the engine hood is opened.1. Engine Hood Courtesy Switch Circuit
2. Body ECUDI±1725
±
Some of the system does not operate.
(Headlight does not come on.)
1. Bulb
2. HEAD Relay
3. DIMMER Relay
4. DRL No. 4 Relay
5. Headlight Dimmer Switch
6. Light Control Switch
7. Wire Harness
8. Body ECU±
BE±27
BE±27
BE±27
BE±27
BE±27
±
±

BE±10
± BODY ELECTRICALTROUBLESHOOTING
3414 Author: Date:
2005 SEQUOIA (RM1146U) Some of the system does not operate.
(Taillight does not come on.)
1. TAIL Fuse
2. TAILLIGHT Relay
3. Light Control Switch
4. Wire Harness
5. Body ECUBE±14
BE±27
BE±27
±
±
Some of the system do not operate.
(Theft deterrent horn or vehicle horn does not sound.)
1. HORN Fuse
2. SECURITY HORN Fuse
3. HORN Relay Circuit
4. Theft Deterrent Horn Circuit
5. Horn
6. Body ECUBE±14
BE±14
BE±145
BE±92
BE±145
±
While the warning is given, the system cannot be canceled by
unlocking the door with a key or transmitter.
1. Door Key Lock and Unlock Switch Circuit (Driver Door
ECU)
Door Key Lock and Unlock Switch Circuit (Passenger
Door ECU)
Door Key Lock and Unlock Switch Circuit (Back Door
ECU)
2. Body ECUDI±1794
DI±1832
DI±1882
±
*1: w/ Glass breakage sensor
WIRELESS DOOR LOCK CONTROL SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
HINT:
Troubleshooting of the wireless door lock control system is based on the premise that the door lock
control system operates normally. Accordingly, before troubleshooting the wireless door lock control
system, first make certain that the door lock control system operates normally.
If the trouble still reappears even though there are no abnormalities in any of the other circuits, check
and replace the Wireless Door Lock Control Receiver as the last step.
SymptomSuspect AreaSee page
All functions of wireless door lock control system do not operate.
1. Transmitter
2. Wireless Door Lock Control Receiver Circuit
3. Body ECUBE±98
DI±1737
±
Wireless door lock operates, but the buzzer does not sound.
(The buzzer does not sound when the customize function prohib-
its.)1. Wireless Door Lock Buzzer Circuit
2. Body ECUDI±1741
±
POWER SEAT CONTROL SYSTEM (w/o Driving Position Memory)
SymptomSuspect AreaSee page
Both Driver and Passenger Power seats do not operate.1. PWR SEAT Fuse
2. Wire HarnessBE±14
±
Driver's seat does not operate.1. Power Seat Switch (D)
2. Wire HarnessBE±109
±
Passenger's seat does not operate.1. Power Seat Switch (P)
2. Wire HarnessBE±109
±
ºSlide operationº does not operate.
1. Power Seat Switch (D, P)
2. Slide Motor (D, P)
3. Wire HarnessBE±109
BE±109
±
ºFront Vertical Operationº does not operate.
1. Power Seat Switch (D)
2. Front Vertical Motor (D)
3. Wire HarnessBE±109
BE±109
±
ºLifter Operationº does not operate.
1. Power Seat Switch (D)
2. Lifter Motor (D)
3. Wire HarnessBE±109
BE±109
±

± BODY ELECTRICALTROUBLESHOOTING
BE±11
3415 Author: Date:
2005 SEQUOIA (RM1146U) ºReclining Operationº does not operate.
1. Power Seat Switch (D, P)
2. Reclining Motor (D, P)
3. Wire HarnessBE±109
BE±109
±
ºLumbar Support Operationº does not operate.
1. Power Seat Switch (D)
2. Lumbar Support Motor (D)
3. Wire HarnessBE±109
BE±109
±
(D): Driver's Seat
(P): Passenger's Seat
POWER SEAT CONTROL SYSTEM (w/ Driving Position Memory)
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspected AreaSee Page
Power seat control system abnormal operation.See DIAGNOSIS SYSTEMDI±1505
POWER MIRROR CONTROL SYSTEM (w/o Driving Position Memory)
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
Mirror does not operate.1. Mirror Switch
2. Wire HarnessBE±115
±
Mirror operates abnormally.
1. Mirror Switch
2. Mirror Motor
3. Wire HarnessBE±115
BE±115
±
POWER MIRROR CONTROL SYSTEM (w/ Driving Position Memory)
SymptomSuspect AreaSee page
Remote control mirror LH only does not operate.
(w/ Driving position memory)1. Remote control mirror motor LH circuit
2. Remote control mirror position sensor LH circuit
3. Driver door ECUDI±1808
DI±1810
±
Remote control mirror RH only does not operate.
(w/ Driving position memory)1. Remote control mirror motor RH circuit
2. Remote control mirror position sensor RH circuit
3. Passenger door ECUDI±1845
DI±1847
±
ELECTRO CHROMIC MIRROR SYSTEM
SymptomSuspect AreaSee page
Electro Chromic Inner Mirror does not operate.
1. ECU±IG Fuse
2. Electro Chromic Inner Mirror
3. Wire HarnessBE±14
BE±122
±
SEAT HEATER SYSTEM
SymptomSuspect AreaSee page
Seat heaters do not operate.
(Driver's and Passenger's)
1. SEAT HTR Fuse
2. Seat Heater Switch (D, P)
3. Seat Heater
4. Wire HarnessBE±14
BE±124
BE±124
±
Driver's seat heater does not operate.1. Seat Heater Switch (D, P)
2. Wire HarnessBE±124
±
Passenger's seat heater does not operate.1. Seat Heater Switch (D, P)
2. Wire HarnessBE±124
±
Seat heater temperature is too hot.Seat HeaterBE±124
AUDIO SYSTEM
SymptomSuspect AreaSee page
Audio system abnormal operation.See DIAGNOSIS SYSTEMDI±1962

± BODY ELECTRICALTROUBLESHOOTING
BE±13
3417 Author: Date:
2005 SEQUOIA (RM1146U)
BACK DOOR POWER WINDOW CONTROL SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
Back door power window does not operate.
1. Back Door Power Window Motor Circuit
2. Window Pulse Sensor Circuit
3. Rear Wiper Motor Circuit
4. Back Door Control Light Switch Circuit
5. Back Door ECU
6. Body ECUIN±35
DI±1877
DI±1880
DI±1864
±
±
TRAILER TOWING
SymptomSuspect AreaSee page
Trailer towing does not operate.
1. TOWING Fuse
2. TOWING TAIL Fuse
3. TOWING BRK Fuse
4. TOWING TAIL Relay
5. BATT CHARGE Relay
6. Towing Converter Relay
7. Brake Controller
8. Wire HarnessBE±14
BE±14
BE±14
BE±148
BE±148
BE±148
BE±148
±