check engine TOYOTA SEQUOIA 2001 Service Repair Manual

DI±280
± DIAGNOSTICSENGINE
474 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check operation of speedometer.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and push the hand±held tester main switch ON.
(c) Start the engine.
(d) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / PRIMARY / VEHICLE SPD.
CHECK:
Read the mass air flow rate on the hand±held tester.
RESULT:
Vehicle speedProceed to
Vehicle speed remains 0 km/h (0 mph)A
Vehicle speed is lower than actual speedA
Vehicle speed is same as actual speedB
B Check for intermittent problems
(See page DI±11).
A

B17411
SPD(+) E6
E5
E1
AT7809
4 to 6 V
Turn the Wheel
3
2
1
I25536
Component Side Connector:
Vehicle Speed Sensor
± DIAGNOSTICSENGINE
DI±281
475 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check voltage between terminal SPD and E1 of ECM connector.
PREPARATION:
(a) Shift the shift lever to neutral.
(b) Jack up the rear wheel on one side.
(c) Turn the ignition switch ON.
CHECK:
Measure the voltage between the specified terminal of the E5
and E6 ECM connector when the wheel is turned slowly.
OK:
Standard:
Tester ConnectionSpecified Condition
SPD (E5±8) ± E1 (E6±1)Generated intermittently
HINT:
The output voltage should fluctuate up and down similarly to the
diagram on the left when the wheel is turned slowly.
OK Replace ECM (See page SF±80).
NG
3 Check vehicle speed sensor.
PREPARATION:
(a) Disconnect the vehicle speed sensor connector.
(b) Connect the battery positive (+) lead to terminal 1 and the
battery negative (±) lead to terminal 2.
(c) Connect the tester positive (+) lead to terminal 3 and the
tester negative (±) lead to terminal 2.
(d) Shift the shift lever to N position.
(e) Rotate the shaft.
CHECK:
Check that there is voltage change between terminals 2 and 3.
OK:
Standard: 0 V to 10 V or more
NG Replace vehicle speed sensor.
OK

BR3795OK NGClearance
B17411
SPD(+) E5
A23540
Wire Harness Side:
Front View
Combination Meter Connector C5
DI±282
± DIAGNOSTICSENGINE
476 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check sensor installation (Vehicle speed sensor).
CHECK:
Check the vehicle speed sensor installation.
OK:
The vehicle speed sensor is installed properly.
NG Tighten sensor installation bolt.
OK
5 Check for open and short in harness and connector between combination meter
and ECM.
PREPARATION:
(a) Disconnect the C5 combination meter connector.
(b) Disconnect the E5 ECM connector.
CHECK:
Check for resistance between the wire harness side connec-
tors.
OK:
Standard (Check for open):
Symbols (Terminal No.)Specified condition
SPD (E5±8) ± C5±25Below 1 W
Standard (Check for short):
Symbols (Terminal No.)Specified condition
SPD (E5±8) or C5±25 ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Check combination meter circuit (See page
DI±1632

± DIAGNOSTICSENGINE
DI±283
477 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0504 Brake Switch ºAº/ºBº Correlation
CIRCUIT DESCRIPTION
In addition to turning on the stop lamps, the stop lamp switch signals are used for a variety of engine, trans-
mission, and suspension functions as well as being an input for diagnostic checks. It is important that the
switch operates properly, therefore this switch is designed with two complementary signal outputs: STP and
ST1±. The ECM analyzes these signal outputs to detect malfunctions in the stop lamp switch.
HINT:
Normal condition is as shown in the table.
SignalBrake pedal releasedIn transitionBrake pedal depressed
STPOFFONON
ST1±ONONOFF
DTC No.DTC Detection ConditionTrouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 sec. or more:
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal is OFF when the ST1± signal is OFF
Short in stop lamp switch signal circuit

Stop lamp fuse

Stop lamp switch

ECM
DID8C±01

± DIAGNOSTICSENGINE
DI±285
479 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check operation of stop light.
CHECK:
Check if the stop lights come on and go off normally when the brake pedal is operated and released.
NG Check and repair stop light circuit.
OK
2 Check stop light switch (See page BE±47).
NG Replace stop light switch.
OK

B17446
Brake Pedal
DepressedBrake Pedal
Released ON
() ()
ST1±(+)E4
E6
E1(±)
DI±286
± DIAGNOSTICSENGINE
480 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check STP signal and ST1± voltage.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) Select the item ºDIAGNOSIS / ENHANCED OBD II /
DATA LIST / ALL / STOP LIGHT SWº.
CHECK:
Read the signal displayed on the hand±held tester.
OK:
Standard:
Brake PedalSpecified Condition
DepressedSTP Signal ON
ReleasedSTP Signal OFF
CHECK:
Measure the voltage between the specified terminals of the E4
and E6 ECM connectors.
OK:
Standard:
Tester ConnectionBrake PedalSpecified Condition
ST1± (E4±12) ±
E1 (E6±1)DepressedBelow 1.5 V
ST1± (E4±12) ±
E1 (E6±1)Released7.5 to 14 V
OK Check for intermittent problems (See page
DI±11).
NG

B17447
Wire Harness Side:
Stop Light Switch Connector
S14
ST1±STP
E4
± DIAGNOSTICSENGINE
DI±287
481 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check harness and connector between ECM and stop light switch.
PREPARATION:
(a) Disconnect the S14 stop light switch connector.
(b) Disconnect the E4 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
Stop light switch (S14±1) ± STP (E4±15)Below 1 W
Stop light switch (S14±3) ± ST1±
(E4±16)Below 1 W
Stop light switch (S14±1) or
STP (E4±15) ± Body ground10 kW or higher
Stop light switch (S14±3) or
ST1± (E4±16) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Replace ECM (See page SF±80).

DI±290
± DIAGNOSTICSENGINE
484 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:

When the throttle position is slightly opened (the accelerator pedal is slightly depressed) because a
floor carpet is overlapped on the accelerator pedal, or if the accelerator pedal is not fully released, etc.,
DTC P0505 will possibly be detected.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.
1 Are there any other codes (besides P0505) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
P0505A
ºP0505º and other DTCsB
HINT:
If any other codes besides P0505 are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI±58).
A
2 Check connection of PCV piping.
NG Repair or replace PCV piping.
OK

± DIAGNOSTICSENGINE
DI±291
485 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check air induction system (See page SF±1).
CHECK:
Check for vacuum leaks in air induction system.
OK:

No leakage.
NG Repair or replace air induction system.
OK
Check electric throttle control system
(See page SF±39).

A05652A18100
Battery2DEFI No. 1
B±Y
E4ECM
BATT 73
2H 1
IA411
B±Y B
F10
Fusible Link
Block 4Engine Room J/B
5
B12
± DIAGNOSTICSENGINE
DI±293
487 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check battery voltage.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON.
(c) Select the item: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / BATTERY VOLTAGE.
CHECK:
Read the battery voltage on the hand±held tester
RESULT:
Battery voltageProceed to
0 VA
Except 0 VB
B Go to step 5.
A