brake light TOYOTA SEQUOIA 2001 Service User Guide

DI±536
± DIAGNOSTICSAUTOMATIC TRANSMISSION
730 Author: Date:
2005 SEQUOIA (RM1146U)
(b) 4 (O/D OFF) position test:
Shift into the 4 (O/D OFF) position and fully depress the accelerator pedal and check the following
points.
(1) Check up±shift operation.
Check that the 1 " 2, 2 " 3 and 3 " 4 up±shifts take place and that the shift point conforms
to the automatic shift schedule (See page SS±24).
HINT:

There is no 5th up±shift in the 4 position.

4th Gear Lock±up Prohibition Control

Brake pedal is depressed.

Accelerator pedal is released.

Engine coolant temperature is 60 °C (140 °F) or less.
(2) Check engine braking.
While driving in the 4 position and 4th gear, release the accelerator pedal and check the engine
braking effect.
(3) Check for abnormal noises during acceleration and deceleration, and for shock at up±shift and
down±shift.
(4) Check the lock±up mechanism.

Drive in 4 position 4th gear, at a steady speed (lock±up ON).

Lightly depress the accelerator pedal and check that the engine speed does not change
abruptly.
HINT:
If there is a big jump in engine speed, there is no lock±up.
(c) 3 position test:
Shift into the 3 position and fully depress the accelerator pedal and check the following points.
(1) Check up±shift operation.
Check that the 1 " 2 and 2 " 3 up±shifts takes place and that the shift point conforms to the
automatic shift schedule (See page SS±24).
HINT:

There is no 4th up±shift and lock±up in the 3 position.

When the 2nd start switch is ON, there is no 1 "2 up±shift and 2 "1 down±shift.
(2) Check engine braking.
While running in the 3 position and 3rd gear, release the accelerator pedal and check the engine
braking effect.
(3) Check for abnormal noises during acceleration and deceleration, and for shock at up±shift and
down±shift.
(d) 2 position test:
Shift into the 2 position and fully depress the accelerator pedal and check the following points.
(1) Check up±shift operation.
Check that the 1 " 2 up±shift takes place and that the shift point conforms to the automatic shift
schedule (See page SS±24).
HINT:

There is no 3rd up±shift and lock±up in the 2 position.

When the 2nd start switch is ON, there is no 1 "2 up±shift and 2 "1 down±shift.

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±537
731 Author: Date:
2005 SEQUOIA (RM1146U)
(2) Check engine braking.
While running in the 2 position and 2nd gear, release the accelerator pedal and check the engine
braking effect.
(3) Check for abnormal noises during acceleration and deceleration, and for shock at up±shift and
down±shift.
(e) L position test:
Shift into the L position and fully depress the accelerator pedal and check the following points.
(1) Check no up±shift.
While running in the L position, check that there is no up±shift to 2nd gear.
(2) Check engine braking.
While running in the L position, release the accelerator pedal and check the engine braking ef-
fect.
(3) Check for abnormal noises during acceleration and deceleration.
(f) R position test:
Shift into the R position, lightly depress the accelerator pedal, and check that the vehicle moves back-
ward without any abnormal noise or vibration.
CAUTION:
Before conducting this test, ensure that the test area is free from people and obstruction.
(g) P position test:
Stop the vehicle on a grade (more than 5°) and after shifting into the P position, release the parking
brake. Then, check that the parking lock pawl holds the vehicle in place.

DIDJ3±01
DI±570
± DIAGNOSTICSAUTOMATIC TRANSMISSION
764 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal ConditionDiagnostic Note
STOP LIGHT SWStop light SW Status/
ON or OFF
Brake Pedal is depressed: ON

Brake Pedal is released: OFF±
PNP SW [NSW]PNP SW Status/
ON or OFFShift lever position is;
P and N: ON
Except P and N: OFF
When the shift lever position dis-
played on the hand±held tester dif-
fers from the actual position, ad-
justment of the PNP switch or the
shift cable may be incorrect.
HINT:
When the failure still occurs even
after adjusting these parts,
See page DI±576.
LOWPNP SW Status/
ON or OFF

Shift lever position is 2: OFF
O

Shift position L switch Push: ON
O

Shift position L switch Push: OFF
=
2NDPNP SW Status/
ON or OFFShift lever position is;
2 and L: ON
Except 2 and L: OFF
=
3RDPNP SW Status/
ON or OFFShift lever position is;
3: ON
Except 3: OFF
=
DRIVEPNP SW Status/
ON or OFFShift lever position is;
D: ON
Except D: OFF
=
REVERSEPNP SW Status/
ON or OFFShift lever position is;
R: ON
Except R: OFF
=
OVERDRV CUT SW2O/D SW Status/
ON or OFF

IG SW ON: ON
O

O/D SW Push: OFF
O

O/D SW Push: ON
±
SHIFTActual Gear Position/
1st, 2nd, 3rd, 4th or 5th
Shift lever position is;

L: 1st

2: 1st or 2nd

3: 1st, 2nd or 3rd

4(O/D OFF): 1st, 2nd, 3rd or 4th

D: 1st, 2nd, 3rd, 4th or 5th
±

DIDJ4±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±573
767 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the page
given.
HINT:
*1 :
... The MIL (Malfunction Indicator Lamp) lights up
*2 :  ... The ECM memorizes the trouble code if the ECM detects the DTC detection condition.
This DTC may be output when the clutch, brake and gear components etc. inside the automatic trans-
mission are damaged.
DTC No.
(See Page)Detection ItemTrouble AreaMIL *1Memory *2
P0500
(DI±278)Vehicle Speed Sensor ºAº
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM


P0705
(DI±576)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input)Open or short in park/neutral position switch circuit
Park/neutral position switch
ECM


P0710
(DI±582)Transmission Fluid Temperature
Sensor ºAº CircuitOpen or short in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0711
(DI±588)Transmission Fluid Temperature
Sensor ºAº PerformanceTransmission wire (ATF temperature sensor No.1)

P0712
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit Low InputShort in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0713
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit High InputOpen in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0717
(DI±591)Input Speed Sensor Circuit No
Signal
Open or short in speed sensor (NT) circuit
Speed sensor (NT)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0722
(DI±596)Output Speed Sensor Circuit No
Signal
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0724
(DI±600)Brake Switch ºBº Circuit High
Short in stop light switch signal circuit
Stop light switch
ECM


P0748
(DI±603)Pressure Control Solenoid ºAº
Electrical
(Shift Solenoid Valve SL1)Open or short in shift solenoid valve SL1 circuit
Shift solenoid valve SL1
ECM


P0751
(DI±608)Shift Solenoid ºAº Performance
(Shift Solenoid Valve S1)Shift solenoid valve S1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0756
(DI±614)Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)Shift solenoid valve S2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0771
(DI±620)Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
Shift solenoid valve SR remains open or closed
Shift solenoid valve SL1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)



DI±600
± DIAGNOSTICSAUTOMATIC TRANSMISSION
794 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0724 Brake Switch ºBº Circuit High
CIRCUIT DESCRIPTION
The purpose of this circuit is to prevent the engine from stalling while driving in lock±up condition when
brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the opera-
tion of the lock±up clutch while braking is in progress.
DTC No.DTC Detection ConditionTrouble Area
P0724
The stop light switch remains ON even when the vehicle is
driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h
(19 mph) or more) fashion 5 times. (2±trip detection logic).
Short in stop light switch signal circuit

Stop light switch

ECM
MONITOR DESCRIPTION
This DTC indicates that the stop light switch remains on. When the stop light switch remains ON during ºstop
and goº driving, the ECM interprets this as a fault in the stop light switch and the MIL comes on and the ECM
stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) ten
times for two driving cycles in order to detect a malfunction.
MONITOR STRATEGY
Related DTCsP0724Stop light switch/Range check/Rationality
Rid /C tMainStop light switchRequired sensors/ComponentsSubVehicle speed sensor
Frequency of operationContinuous
DurationGO and STOP 5 times
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
Battery voltage8 V or more±
Ignition switchON
StarterOFF
GO (Vehicle speed is 30 km/h
(18.63 mph) or more)Once
STOP (Vehicle speed is less than 3 km/h
(1.86 mph))Once
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Brake switchRemain ON during GO and STOP 5 times
DIDJA±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±601
795 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
See page DI±283.
INSPECTION PROCEDURE
1 Read value of DATA LIST (STP signal).
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
Standard:
ItemMeasurement Item/
Range (display)Normal Condition
Stop Light SwitchStop light SW Status/
ON or OFF
Brake Pedal is depressed: ON

Brake Pedal is released: OFF
NOTICE:
In the table above, the conditions listed under ºNormal Conditionº are reference conditions. Do not
depend solely on these reference conditions when deciding whether a part is faulty or not.
OK:
Brake Pedal ConditionSpecified Condition
DepressedON
ReleasedOFF
NG Go to step 2.
OK
Go to step 3.

I21525
Free Pushed in
D14167
ECM:
E8E7E6E5E4
STP(+)
DI±602
± DIAGNOSTICSAUTOMATIC TRANSMISSION
796 Author: Date:
2005 SEQUOIA (RM1146U)
2 Inspect stop light switch.
PREPARATION:
Remove the stop lamp switch assy.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Switch positionTester ConnectionSpecified Condition
Switch pin free1 ± 4Below 1 W
Switch pin pushed in=10 kW or higher
Switch pin free2 ± 310 kW or higher
Switch pin pushed in=Below 1 W
NG Replace stop light switch (See page BR±8).
OK
3 Check harness and connector (ECM ± stop light switch).
PREPARATION:
Install the stop lamp switch assy.
CHECK:
Measure the voltage according to the value(s) in the table be-
low when the brake pedal is depressed and released.
OK:
ConditionTester ConnectionSpecified Condition
Brake pedal is depressedE4 ± 15 (STP) ±
Body ground10 to 14 V
Brake pedal is released=Below 1 V
NG Repair or replace the harness or connector
(See page IN±35).
OK
Replace the ECM (See page SF±80).

C00083
DLC3
CG TC
TS
F16800
Height
Control
Manual
Indicator
Lamp
DI±712
± DIAGNOSTICSAIR SUSPENSION SYSTEM
906 Author: Date:
2005 SEQUOIA (RM1146U)

The TS terminal circuit uses CAN (Controller Area Net-
work) for communication. Therefore, if there are any mal-
functions in the communication circuit, one or more DTCs
in the CAN communication system is/are output.
(6) Set each of the check items to the condition shown
under Operation (B) in the test mode table below.
HINT:
When checking each item, the height control manual indicator
lamp comes on for 1 second.
Test mode table:
Check ItemOperation (A)Operation (B)
Stop light switch signalOFF (Brake pedal not depressed)ON (Brake pedal depressed)
Door courtesy light switch signalON (Each door opened)OFF (All doors closed)
Height control switch signal±Press the height control switch ºUPº first and
then press ºDOWNº
Height control mode select switch signalOFF (Height control mode select switch not
pushed in)ON to OFF (Height control mode select switch
pushed in and released)
(7) Using SST, connect the 3rd terminal of the SST
check wire to terminal TC of the DLC3.
SST 09843±18040
(8) Read the number of blinks of the height control
manual indicator lamp.

± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±715
909 Author: Date:
2005 SEQUOIA (RM1146U)
Test mode (input signal check) table:
Check ItemOperation (A)Operation (B)
Stop light switch signalOFF (Brake pedal not depressed)ON (Brake pedal depressed)
Door courtesy light switch signalON (Each door opened)OFF (All doors closed)
Height control switch signal±Press the height control switch ºUPº first and
then press ºDOWNº
Height control mode select switch signalOFF (Height control mode select switch not
pushed in)ON to OFF (Height control mode select switch
pushed in and released)
HINT:
In step (6), all signals can be checked together.
(7) Read the test mode DTCs by following the prompts
on the tester screen.
HINT:
Refer to the hand±held tester operator's manual for further de-
tails.
(8) Check the malfunction using the code table below.
DTC of air suspension system test mode (input signal check) function:
If a trouble code is displayed during the test mode DTC check, check the circuit listed for that code. For details
of each code, refer to ºSee pageº under the respective DTC No. in the chart.
DTC No.
(See Page)Detection ItemTrouble Area
C1782/82
(DI±767)Stop light switch circuit malfunction

Stop light switch assy

Stop light switch circuit

Suspension control ECU
C1783/83
(DI±770)Door courtesy switch circuit malfunction

Door courtesy light switch assy

W/ Motor back door assy

Door courtesy light switch circuit

Body ECU

Back door ECU

Suspension control ECU
C1786/86
(DI±774)Height control switch circuit malfunction

Height control switch

Height control switch circuit

Suspension control ECU
C1788/88
(DI±778)Height control mode select switch circuit malfunction

Height control mode select switch

Height control mode select switch circuit

Suspension control ECU
(9) After completing the test mode, disconnect the tes-
ter and turn the ignition switch off.

F16807
GND
F19430
GND
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±719
913 Author: Date:
2005 SEQUOIA (RM1146U) RM+ (S25±20) ±
GND (S25±22)
R±L ± W±B
Height Control
Compressor
Motor Lock (+)Engine idling, vehicle height changes from ºNORMALº to
ºHIGHº by pressing the height control switch (While
height control compressor assy is working).
Below 1.0 V
RM± (S25±21) ±
Body groundBR±Y ± W±B
Height Control
Compressor
Motor Lock (±)
AlwaysBelow 1.0 V
GND (S25±22) ±
Body groundW±B ±
Body groundGroundAlwaysBelow 1.0 V
B (S25±24) ±
GND (S25±22)V ± W±BBatteryIG switch ON10 to 14 V
LO (S25±26) ± PWB
Height Control
I di t ºLOº
Engine idling, vehicle height is ºNORMALº "
P i th ºDOWNº b tt f th h i ht t l it h10 V or more "LO (S25 26)
GND (S25±22)P ± W±BIndicator ºLOº
SignalPressing the ºDOWNº button of the height control switch
turns on the ºLOº indicator lamp (*1)10 V or more "
Below 5 V
STP (S25±27) ± GY WBStop LightBk dld dRl d10 to 14 V "STP (S25 27)
GND (S25±22)G±Y ± W±BSto Light
SwitchBrake pedal depressed " Released10 to 14 V "
Below 1.5 V
SIL (S25±30) ±
GND (S25±22)G±R ± W±BDiagnosis Sig-
nalHand±held tester is connected to DLC3Pulse generation
(See waveform 3)
DOOR (S25±31) ± RWBDSilIG switch ON, each door opened "Below 1.5 VDOOR (S25 31)
GND (S25±22)R ± W±BDoor SignalIG switch ON, each door o ened "
All door closed
Below 1.5 V
10 to 14 V
DNSW (S25±32) ±
GND (S25±22)W ± W±B
Height Control
Switch
ºDOWNº SignalIG switch ON, ºDOWNº button of height control switch
pushed in "
ºDOWNº button of height control switch releasedBelow 1.5 V "
10 to 14 V
BAT (S25±25) ±
GND (S25±22)V ± W±BBatteryAlways10 to 14 V
CANL (S25±28) ±
GND (S25±22)W ± W±BCAN Commu-
nication SignalIG switch ONPulse generation
(See waveform 1)
CANH (S25±29) ±
GND (S25±22)G ± W±BCAN Commu-
nication SignalIG switch ONPulse generation
(See waveform 2)
*1: Perform inspection after checking that the height control indicator lamp switches are illuminated when
the height control switch button is pressed.
Waveform 1 (Reference):
ItemContents
TerminalCANL ± GND
Tool setting1V/DIV, 10ms/DIV
Vehicle conditionIgnition SW ON, Engine stopped
Waveform 2 (Reference):
ItemContents
TerminalCANH ± GND
Tool setting1V/DIV, 10ms/DIV
Vehicle conditionIgnition SW ON, Engine stopped