warning TOYOTA SEQUOIA 2001 Service User Guide

DIDIP±01
12345678
9 10111213141516
D13649
DLC3:
CG
TC
D13654
DI±524
± DIAGNOSTICSAUTOMATIC TRANSMISSION
718 Author: Date:
2005 SEQUOIA (RM1146U)
BASIC INSPECTION
1. CHECK FLUID LEVEL
(a) Using SST, create a short±circuit between terminals TC
and CG of the DLC3.
SST 09843±18040
(b) Start the engine and run at idle.

The A/C switch must be turned off.

On models with active height control suspension &
adaptive variable suspension, turn the height con-
trol switch off.
(c) Slowly move the shift lever through all positions from P to
L, and move it back to the P position.
(d) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or from
D to N, within 1.5 seconds. (Repeat this operation for 6 se-
conds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(e) Return the shift lever to the P position and disconnect ter-
minals TC and CG.
(f) Idle the engine to raise oil temperature.
(g) Lift up the vehicle immediately after the meter indicator
light (ATF temperature warning light) comes on.

The A/T OIL TEMP warning light indicates the ATF
temperature according to the following table.
ATF Temp.Less than optimized
temperatureOptimized temperatureMore than optimized
temperature
A/T OIL TEMP warning lightOFFONBlinking

D13654
D14231
When fluid
temperature
is low: offWhen fluid
temperature
is correct: onWhen fluid
temperature
is high: blinks
D14139Overflow Plug
DI±530
± DIAGNOSTICSAUTOMATIC TRANSMISSION
724 Author: Date:
2005 SEQUOIA (RM1146U)
(11) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or
from D to N, within 1.5 seconds. (Repeat this opera-
tion for 6 seconds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(12) Disconnect terminals TC and CG after confirming
the above condition.
(13) Idle the engine to raise the fluid temperature.
(14) Lift up the vehicle immediately after the meter indi-
cator light (ATF temperature warning light) comes
on.
NOTICE:

Add fluid only when the meter indicator light is on.

Perform this procedure while the engine is idling.
(15) Remove the overflow plug. If ATF overflows, pro-
ceed to [*2].
If ATF does not overflow, proceed to [*3].
HINT:
ºOverflowº indicates the condition under which ATF drains out
from the overflow tube.
NOTICE:
Capacity of the overflow tube is approximately 3 cc.

D14141
12345678
9 10111213141516
D13649
DLC3:
CG
TC
D13654
DI±532
± DIAGNOSTICSAUTOMATIC TRANSMISSION
726 Author: Date:
2005 SEQUOIA (RM1146U)
(3) Install the overflow plug with a new gasket when the
draining ATF has becomes a trickle.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(4) Install the refill plug with a new O±ring.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(5) Lower down the vehicle.
(6) Turn the ignition switch off.
(7) Check for fluid leaks in the transmission.
If there are leaks, it is necessary to repair or replace O±rings,
FIPGs, oil seals, plugs or other related parts.
(d) When adding a minimum amount of fluid: [*4]
(1) Using SST, create a short±circuit between terminals
TC and CG of the DLC3.
SST 09843±18040
(2) Start the engine and run at idle.
NOTICE:
The A/C switch must be turned off.
(3) Slowly move the shift lever from the P to the 2±L
position. Return the shift lever to the P position.
(4) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or
from D to N, within 1.5 seconds. (Repeat this opera-
tion for 6 seconds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(5) Disconnect terminals TC and CG after confirming
the above condition.
(6) Idle the engine to raise the fluid temperature.

D14231
When fluid
temperature
is low: offWhen fluid
temperature
is correct: onWhen fluid
temperature
is high: blinks
D14139Overflow Plug
D14141
D14140
Refill Plug
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±533
727 Author: Date:
2005 SEQUOIA (RM1146U)
(7) Lift up the vehicle immediately after the meter indi-
cator light (ATF temperature warning light) comes
on.
NOTICE:

Add fluid only when the meter indicator light is on.

Perform this procedure while the engine is idling.
(8) Remove the overflow plug. If ATF overflows, pro-
ceed to [*5]. If ATF does not overflow, proceed to
[*6].
HINT:
ºOverflowº indicates the condition under which ATF drains out
from the overflow tube.
(e) When fluid overflows: [*5]
(1) Install the overflow plug with a new gasket when the
draining ATF has become a trickle.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(2) Install the refill plug with a new O±ring.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(3) Lower down the vehicle.
(4) Turn the ignition switch off.
(5) Check for fluid leaks in the transmission.
If there are leaks, it is necessary to repair or replace O±rings,
FIPGs, oil seals, plugs or other related parts.
(f) When fluid does not overflow: [*6]
(1) Remove the refill plug.

DI±554
± DIAGNOSTICSAUTOMATIC TRANSMISSION
748 Author: Date:
2005 SEQUOIA (RM1146U) Shift point too high or too low
1. Shift solenoid valve (SLT) circuit *1
2. Speed sensor NT circuit *1
3. Speed sensor SP2 circuit *1
4. Throttle position sensor circuit *1
5. ATF temperature sensor circuit *1
6. ECM
DI±662
DI±591
DI±596
DI±58
DI±582
IN±35
Up±shift to 5th from 4th while shift lever is in 4 position1. O/D main switch circuit
2. ECMDI±688
IN±35
Up±shift to 5th from 4th while engine is cold1. Engine coolant temp. sensor circuit *1
2. ECM
DI±58
IN±35
Up±shift to 4th from 3rd while shift lever is in 3 position1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35
Up±shift to 3rd from 2nd while shift lever is in 2 position1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35
Up±shift to 2nd from 1st while shift lever is in L position1. Shift position L switch circuit
2. ECMDI±691
IN±35
Harsh engagement (N " D)
1. Speed sensor NT circuit *1
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SLT) circuit *1
4. ECM
DI±591
DI±603
DI±662
IN±35
Harsh engagement (Lock±up)
1. Speed sensor NT circuit *1
2. Speed sensor SP2 circuit *1
3. Shift solenoid valve (SLU) circuit *1
4. ECM
DI±591
DI±596
DI±680
IN±35
Harsh engagement (Any driving position)ECMIN±35
Poor acceleration
1. ATF temperature sensor No.2 circuit *1
2. Engine coolant temp. sensor circuit *1
3. Shift solenoid valve (SLT) circuit *1
4. ECM
DI±666
DI±58
DI±662
IN±35
No engine brakingECMIN±35
No kick±downECMIN±35
Engine stalls when starting off or stopping1. Shift solenoid valve (SLU) circuit *1
2. ECM
DI±680
IN±35
AT Oil Temp. warning light remains on1. ATF temperature sensor No.2 circuit*1DI±666
Lock±up at 3rd gear
1. AT F temperature sensor No.2 circuit 1
2. Engine coolant temp. sensor circuit *1DI±666
DI±58
Shift point too high
2. Engine coolant tem . sensor circuit
3. ECMDI 58
IN±35
Malfunction in shifting1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35

DI±666
± DIAGNOSTICSAUTOMATIC TRANSMISSION
860 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2740 Transmission Fluid Temperature Sensor ºBº
Circuit
DTC P2742 Transmission Fluid Temperature Sensor ºBº
Circuit Low Input
DTC P2743 Transmission Fluid Temperature Sensor ºBº
Circuit High Input
CIRCUIT DESCRIPTION
ATF (Automatic Transmission Fluid) temperature sensor No.2 is on the transmission and just in front of the
oil cooler inlet pipeline.
If ECM detects the abnormally high temperature of ATF by this sensor, it draws driver's attention by illuminat-
ing the warning lamp.
HINT:

The temperature of ATF easily rises when towing, climbing hills and in traffic, etc.

If the ATF temperature sensor No.2 becomes short±circuited, the signal that indicates the ATF temper-
ature is 150C (302F) or higher is input in ECM.
Vehicle conditions when the sensor is normal and when the sensor is short±circuited are indicated
in the table below.
ATF temperature Sensor No.2
StateDetection ConditionSymptomRecovery Condition

AT fluid temp. more than 150C
(302F).
AT Oil Temp. warning light re-
mains on
AT fluid temp. less than 135C
(275F). *2

AT fluid temp. more than 130C
(266F).
Shift point too high.
AT fluid temp. less than 110C
(230F).
Sensor is normalWhen the conditions (a) and (b)
are satisfied.
(a) AT fluid temp. more than 130C
(266F).
(b) Engine coolant temp. more
than 95C (203F).

Lock±up at 3rd gear. *1
AT fluid temp. less than 110C
(230F) *2 and engine coolant
temp. less than 95C (203F).
Sensor is short±circuited

Any conditions.

AT Oil Temp. warning light re-
mains on

Shift point too high.

Symptoms still occur
Sensor is short circuited

Engine coolant temp. more than
95C (203F).
Lock±up at 3rd gear. *1
Symptoms still occur
HINT:
*1: When AT fluid temperature is normal, transmission locks up at 5th gear with the shift lever in D position
and at 4th gear with the shift lever in 4 position.
*2: When AT fluid temperature is in normal range, it decreases to less than 135C (275F) within 5 minutes
with the shift lever in P or N position in an idling state.
DIDJN±01

± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±771
965 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Inspect courtesy light switch.
CHECK:
Check that the open door warning light comes on when any door or back door is opened and goes off when
all the doors are closed.
OK:
Courtesy light operates normally.
NG Check open door warning light
(See page DI±1608).
OK

DIDJT±01
F19148
Combination Meter
Tire Pressure
Warning Lamp DI±796
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
990 Author: Date:
2005 SEQUOIA (RM1146U)
TIRE PRESSURE WARNING SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77
1. TIRE PRESSURE WARNING SYSTEM PRECAUTION
(a) When the tire pressure warning lamp comes on, immedi-
ately check the tire pressure of the tire and adjust it to the
specified pressure. (The tire pressure warning lamp
comes on if there is an open in the tire pressure warning
lamp circuit.)
NOTICE:
Check the spare tire as well since this system monitors
pressure of all tires, including the spare.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) When the tire pressure warning lamp blinks, there is a
malfunction in the system. Check for DTCs.
(c) It is necessary to register the transmitter ID in the tire pres-
sure monitor ECU when replacing the tire pressure moni-
tor valve sub±assy and/or tire pressure monitor ECU (see
page DI±805).
(d) When replacing the tire pressure monitor ECU.
(1) Using the DATA LIST, read the transmitter IDs regis-
tered in the ECU and make a note of them before
removing the tire pressure monitor ECU.
(2) Register the transmitter IDs after installing a new
tire pressure monitor ECU.
(e) When replacing the tire pressure monitor valve sub±assy.
(1) Make a note of the 7 digit number (transmitter ID)
written on the tire pressure monitor valve sub±assy
when replacing the tire pressure monitor valve sub±
assy. Register the transmitter IDs in the tire pres-
sure monitor ECU after replacing the tire pressure
monitor valve sub±assy and installing the tires and
wheels on the vehicle.

F19132
Transmitter ID
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±797
991 Author: Date:
2005 SEQUOIA (RM1146U)
NOTICE:
The transmitter ID is written on the tire pressure monitor
valve sub±assy and ID can not be seen after installing the
tire pressure monitor valve sub±assy on the tire and wheel.
Therefore, make a note of the transmitter ID before instal-
ling the tire pressure monitor valve sub±assy.
2. IN CASE OF TIRE AND WHEEL REPLACEMENT
(a) When tires and wheels are replaced, register the transmitter ID without fail.
3. IN CASE OF TIRE ROTATION OR REPLACEMENT OF TIRE PRESSURE MONITOR ECU, TIRE
PRESSURE MONITOR VALVE SUB±ASSY, OR TIRES WITH DIFFERENT TIRE PRESSURE
(a) Initialize the tire pressure warning system after one of the following is performed:

Replacing the tire pressure monitor ECU or the tire pressure monitor valve sub±assy

Tire rotation

Replacing tires with different tire pressure
HINT:
The tire pressure warning system will not operate properly if it is not initialized (see page DI±808).
4. FAIL±SAFE FUNCTION
(a) When a system malfunction occurs in the tire pressure warning system, the tire pressure warning lamp
blinks and informs the driver of the system failure.
(b) The result of this diagnosis is stored in the tire pressure monitor ECU.

DIDJU±01
F19149
Tire Pressure Sensor
(Tire Pressure Monitor
Valve Sub±assy)
Tire Pressure Sensor
(Tire Pressure Monitor
Valve Sub±assy)Tire Pressure Sensor
(Tire Pressure Monitor
Valve Sub±assy) Combination Meter Assy

Tire Pressure Warning Lamp
Tire Pressure
Monitor ECU
Tire Pressure Warning
Reset Switch
Tire Pressure Sensor
(Tire Pressure Monitor Valve Sub±assy) Tire Pressure Sensor
(Tire Pressure Monitor
Valve Sub±assy)
Tire Pressure Monitor
Receiver Assy
DI±798
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
992 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION