O2 sensor harness TOYOTA SEQUOIA 2001 Service Owner's Manual

B17416HT1BECM Connector
E7OX1B E8
HT2B
OX2B
A21341
+B
OX E1HT
H2
H4
Components Side:
Bank 1 Sensor 2, Bank 2 Sensor 2
DI±158
± DIAGNOSTICSENGINE
352 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check for short in harness and connector between terminal OX1B and HT1B,
OX2B and HT2B of ECM.
PREPARATION:
(a) Turn the ignition switch to OFF and wait for 5 minutes.
(b) Disconnect the E7 and E8 ECM connector.
CHECK:
(a) Check the resistance.
OK:
Standard:
Tester ConnectionsSpecified Conditions
HT1B (E8±1) ± OX1B (E8±18)10 kW or higher
HT2B (E7±5) ± OX2B (E5±33)10 kW or higher
OK Replace ECM (See page SF±80
NG
4 Check resistance of heated oxygen sensor heater.
PREPARATION:
Disconnect the heated oxygen sensor connector.
CHECK:
Measure resistance between terminals of the heated oxygen
sensor.
OK:
Standard:
Tester ConnectionSpecified Condition
HT (1) ± +B (2)11 to 16 W at 20°C (68°F)
+B (2) ± OX (3)10 kW or higher
NG Replace heated oxygen sensor.
OK
Repair or replace harness or connector.
5 Perform confirmation driving pattern.
NEXT

A23543
+B
OXR2
OXL2E1 HTR2
HTL2
H2
H4
Wire Harness Side:
Bank 1 Sensor 2, Bank 2 Sensor 2
B17416HT1BECM Connector E7OX1B E8
HT2B
OX2B
A21040
Reference (Bank 1 Sensor 1 System Drawing)
From
BatteryEFI No. 1 FuseEFI Relay
EFI No. 2 FuseHeater Oxygen
Sensor
Heater
SensorHT1A
OX1A
E2
MRELECM
DI±164
± DIAGNOSTICSENGINE
358 Author: Date:
2005 SEQUOIA (RM1146U)
17 Check for open and short in harness and connector between ECM and heated
oxygen sensor.
PREPARATION:
(a) Disconnect the heated oxygen sensor connector.
(b) Disconnect the E7 and E8 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
OXL2 (H2±3) ± OX1B (E8±18)Below 1 W
HTL2 (H2±1) ± HT1B (E8±1)Below 1 W
OXR2 (H4±3) ± OX2B (E7±33)Below 1 W
HTR2 (H4±1) ± HT2B (E7±5)Below 1 W
OXL2 (H2±3) or OX1B (E8±18) ±
Body ground10 kW or higher
HTL2 (H2±1) or HT1B (E8±1) ±
Body ground10 kW or higher
OXR2 (H4±3) or OX2B (E7±33) ±
Body ground10 kW or higher
HTR2 (H4±1) or HT2B (E7±5) ±
Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Replace heated oxygen sensor.

A19288
A/F Relay
A23659
Wire Harness Side:
HT
A38
Sensor 1A/F Sensor Connector
AF+
Front ViewAF±
+B A39
B17415
E7ECM Connector
HA1A
A1A+
A1A±
A2A+
A2A±HA2A
± DIAGNOSTICSENGINE
DI±175
369 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check A/F relay.
PREPARATION:
Remove the A/F relay from the engine room J/B.
CHECK:
Inspect the A/F relay.
OK:
Standard:
Terminal No.ConditionSpecified Condition
3 ± 5Always10 KW or higher
3 ± 5Apply B+ between
terminals 1 and 2Below 1 W
NG Replace A/F relay.
OK
13 Check for open and short in harness and connector between ECM and A/F sen-
sor.
PREPARATION:
(a) Disconnect the A38 or A39 A/F sensor connector.
(b) Turn the ignition switch to ON.
CHECK:
(a) Measure the voltage between the +B terminal of the A/F
sensor connector and body ground.
OK:
Standard:
Tester ConnectionsSpecified Conditions
+B (2) ± Body ground9 to 14 V
PREPARATION:
(a) Turn the ignition switch to OFF.
(b) Disconnect the E7 ECM connector.
CHECK:
(a) Check the resistance.
OK:
Standard (Check for open):
Tester ConnectionsSpecified Conditions
HT (A38±1) ± HA1A (E7±2)
HT (A39±1) ± HA2A (E7±1)Below 1 W
AF+ (A38±3) ± A1A+ (E7±22)
AF+ (A39±3) ± A2A+ (E7±23)Below 1 W
AF± (A38±4) ± A1A± (E7±30)
AF± (A39±4) ± A2A± (E7±31)Below 1 W

A23512
Reference (Bank 1 Sensor 1 System Drawing):
A/F Sensor A/F Relay
Heater
Sensor
A1A+ HA1A
Duty
Control ECM
From
Battery
A/F Heater
Fuse
A1A±
To EFI Relay
DI±176
± DIAGNOSTICSENGINE
370 Author: Date:
2005 SEQUOIA (RM1146U)
Standard (Check for short):
Tester ConnectionsSpecified Conditions
HT (A38±1) or HA1A (E7±2) ± Body ground
HT (A39±1) or HA2A (E7±1) ± Body ground10 kW or higher
AF+ (A38±3) or A1A+ (E7±22) ± Body ground
AF+ (A39±3) or A2A+ (E7±23) ± Body ground10 kW or higher
AF± (A38±4) or A1A± (E7±30) ± Body ground
AF± (A39±4) or A2A± (E7±31) ± Body ground10 kW or higher
NG Replace or replace harness or connector.
OK
14 Replace air fuel ratio sensor.
NEXT

B17411
KNK1
KNK2EKN2
EKNK E7
DI±208
± DIAGNOSTICSENGINE
402 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector between EB4 connector and
ECM (See page IN±35).
NG Repair or replace harness or connector.
OK
3 Measure voltage between terminals KNK1 and EKNK, KNK2 and EKN2 of ECM.
PREPARATION:
(a) Disconnect the E7 ECM connector.
(b) Turn the ignition switch to ON.
CHECK:
(a) Measure the voltage between the specified ECM termi-
nals.
OK:
Standard:
Tester ConnectionSpecified Condition
KNK1 (E7±29) ± EKNK (E7±28)4.5 to 5.5 V
KNK2 (E7±21) ± EKN2 (E7±20)4.5 to 5.5 V
(b) Reconnect the ECM connector.
NG Replace ECM (See page SF±80).
OK
Check for intermittent problems
(See page DI±11).
4 Check knock sensor installation.
CHECK:
Check the knock sensor installation.
OK:
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
NG Tighten the sensor.
OK

A23513
Male Connector
EB4
Wire Harness Side:
Front View
± DIAGNOSTICSENGINE
DI±209
403 Author: Date:
2005 SEQUOIA (RM1146U)
Replace knock sensor (See page SF±66).
5 Check knock sensor.
PREPARATION:
(a) Disconnect the EB4 connector.
CHECK:
(a) Check the resistance between the terminals of the EB4
male connector.
OK:
Standard:
Tester ConnectionSpecified Condition
EB4 male connector 3 ±4120 to 280 kW
EB4 male connector 7 ± 8120 to 280 kW
(b) Reconnect the EB4 connector.
OK Check for intermittent problems
(See page DI±11).
NG
6 Check for open and short in harness and connector between EB4 connector and
knock sensor (See page IN±35).
HINT:

If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the right
bank side.

If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the left
bank side.
NG Repair or replace harness or connector.
OK
Replace knock sensor.

A21027
Wire Harness Side
Crankshaft Position Sensor C2
B17414
E6ECM Connector
NE± NE+
BR3795OK NGClearance
DI±214
± DIAGNOSTICSENGINE
408 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector between ECM and
crankshaft position sensor.
PREPARATION:
(a) Disconnect the C2 crankshaft position sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
Crankshaft position sensor (C2±1) ±
NE+ (E6±21)Below 1 W
Crankshaft position sensor (C2±2) ±
NE± (E6±20)Below 1 W
Crankshaft position sensor (C2±1) or
NE+ (E6±21) ± Body ground10 kW or higher
Crankshaft position sensor (C2±2) or
NE± (E6±20) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
3 Check sensor installation (crankshaft position sensor).
CHECK:
Check the crankshaft position sensor installation.
OK:
The crankshaft position sensor is installed properly.
NG Tighten sensor installation bolt.
OK

DI±218
± DIAGNOSTICSENGINE
412 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
P0340, P0345 Case 1:
VVT sensor signalNo signal
P0340, P0345 Case 2:
VVT sensor signalNo signal
P0341, P0346:
VVT sensor count12 or more / 720CA (= Engine 2 revolutions)
COMPONENT OPERATING RANGE
ParameterStandard Value
VVT sensor signal input during every 720CA3
WIRING DIAGRAM
Refer to DTC P0335 on page DI±210.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check resistance of camshaft position sensor (See page SF±76).
NG Repair or replace harness or connector.
OK

B17414
E6
ECM Connector
VV2+
VV1±
VV1+VV2±
A21029
Wire Harness Side
VVT Sensor V16
V17
BR3795OK NGClearance
± DIAGNOSTICSENGINE
DI±219
413 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check for open and short in harness and connector between ECM and VVT sen-
sor.
PREPARATION:
(a) Disconnect the VVT sensor connector.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
VVT sensor (V16±1) ± VV1+ (E6±25)Below 1 W
VVT sensor (V16±2) ± VV1± (E6±24)Below 1 W
VVT sensor (V17±1) ± VV2+ (E6±18)Below 1 W
VVT sensor (V17±2) ± VV2± (E6±28)Below 1 W
VVT sensor (V16 ±1) or
VV1+ (E6±25) ± Body ground10 kW or higher
VVT sensor (V16±2) or
VV1± (E6±24) ± Body ground10 kW or higher
VVT sensor (V17 ±1) or
VV2+ (E6±18) ± Body ground10 kW or higher
VVT sensor (V17±2) or
VV2± (E6±28) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
3 Check sensor installation (VVT position sensor).
CHECK:
Check the VVT position sensor installation.
OK:
The VVT sensor is installed properly.
NG Tighten sensor installation bolt.
OK

DI±264
± DIAGNOSTICSENGINE
458 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0450 Evaporative Emission Control System Pres-
sure Sensor/Switch
DTC P0451 Evaporative Emission Control System Pres-
sure Sensor/Switch Range/Performance
DTC P0452 Evaporative Emission Control System Pres-
sure Sensor/Switch Low Input
DTC P0453 Evaporative Emission Control System Pres-
sure Sensor/Switch High Input
DTC SUMMARY
DTCMonitoring ItemsMalfunction Detection ConditionsTrouble AreasDetection Tim-
ingsDetection
Logic
P0450Pressure sensor voltage ab-
normal fluctuationSensor output voltage rapidly fluctuates
beyond upper and lower malfunction
thresholds for 0.5 seconds.
Pump module

Connector/Wire harness
(Pump module ± ECM)

ECM
EVAP monitor-
ing (ignition
OFF)

Ignition ON
1 trip
P0451Pressure sensor noisingSensor output voltage fluctuates fre-
quently in certain time period.

Pump module

Connector/Wire harness
(Pump module ± ECM)

ECM
EVAP monitor-
ing (ignition
OFF)

Engine running
2 trip
P0451Pressure sensor stuckSensor output voltage does vary in cer-
tain time period.

Pump module

Connector/Wire harness
(Pump module ± ECM)

ECM
EVAP monitor-
ing (ignition
OFF)
2 trip
P0452Pressure sensor voltage lowSensor output voltage is less than 0.45
V for 0.5 seconds.

Pump module

Connector/Wire harness
(Pump module ± ECM)

ECM
Ignition ON

EVAP monitor-
ing (ignition
OFF)
1 trip
P0453Pressure sensor voltage highSensor output voltage is more than 4.9
V for 0.5 seconds.

Pump module

Connector/Wire harness
(Pump module ± ECM)

ECM
Ignition ON

EVAP monitor-
ing (ignition
OFF)
1 trip
HINT:
The pressure sensor is built into the pump module.
CIRCUIT DESCRIPTION
The circuit description can be found in the EVAP (Evaporative Emission) Inspection Procedure (see page
DI±460).
DID89±01