Ts terminal TOYOTA SEQUOIA 2001 Service Owner's Manual

A2364720 msec./DIV 20 V/DIV
Ground
DI±36
± DIAGNOSTICSENGINE
230 Author: Date:
2005 SEQUOIA (RM1146U) OX2B (E7±33) ± E2 (E8±28)
R ± G±WIdlingPulse generation
(See waveform 10)
STP (E4 15) E1 (E6 1)GY BRBrake pedal is depressed7.5 to 14 VSTP (E4±15) ± E1 (E6±1)G±Y ± BRBrake pedal is releasedBelow 1.5 V
ST1 (E4 16) E1 (E6 1)LB BRBrake pedal is depressedBelow 1.5 VST1± (E4±16) ± E1 (E6±1)L±B ± BRBrake pedal is released7.5 to 14 V
STA (E6±11) ± E1 (E6±1)B±R ± BRShift lever position P or N, Ignition switch START6.0 V or more
STSW (E6±12) ± E1 (E6±1)B ± BRShift lever position P or N, ignition switch START6.0 V or more
STAR/NSW (E7 8) E1 (E6 1)BBRIG switch ON, Other shift position in P, N9 to 14 VSTAR/NSW (E7±8) ± E1 (E6±1)B ± BRIG switch ON, Shift position in P, N0 to 3.0 V
W (E5 30) E1 (E6 1)VW BRIdling9 to 14 VW (E5±30) ± E1 (E6±1)V±W ± BRIG switch ONBelow 3.0 V
TACH (E5±1) ± E1 (E6±1)Y±G ± BRIdlingPulse generation
(See waveform 11)
ACIS (E8±33) ± E1 (E6±1)B±L ± BRIG switch ON9 to 14 V
VPMP (E4±5) ± E1 (E6±1)P±L ± BRIgnition switch ON9 V to 14 V
MPMP (E4±6) ± E1 (E6±1)V±G ± BR
Vacuum pump OFF

Vacuum pump ON0 V to 3 V
9 V to 14 V
PPMP (E4±22) ± E1 (E6±1)R±G ± BRIgnition switch ON3 V to 3.6 V
AIV1 (E8±27) ± E1 (E6±1)L±B ± BRIgnition switch ON9 to 14 V
AIV2 (E8±26) ± E1 (E6±1)P±L ± BRIgnition switch ON9 to 14 V
AIRV (E4±4) ± E1 (E6±1)R±W ± BRIgnition switch ON9 to 14 V
AIRP (E4±25) ± E1 (E6±1)G±W ± BRIgnition switch ON9 to 14 V
AIP (E8±32) ± E1 (E6±1)B±Y ± BRIgnition switch ON3 V to 3.6 V
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
WAVEFORM 1
Fuel injector
ECM Terminal NamesBetween #10 (to 40) and E01
Tester Ranges20 V/DIV, 20 msec./DIV
ConditionsIdling
HINT:
The wavelength becomes shorter as the engine rpm increases.

A23648
GND 1V/ DIV KNK1 Signal Waveform
1 msec./ Division
A23649
200 msec./DIV 5 V/DIV
GroundA
B
A23650
20 msec./DIV 2 V/DIV
(a) Ground CH1
(b) Ground CH2
(c) Ground CH3
± DIAGNOSTICSENGINE
DI±37
231 Author: Date:
2005 SEQUOIA (RM1146U)
WAVEFORM 2
Knock sensor
ECM Terminal NameBetween KNK1 and EKNK
Between KNK2 and EKN2
Tester Range1 V/DIV, 1 msec./DIV
ConditionMaintain engine RPM at 2,000 rpm after engine warmed±up
HINT:

The wavelength becomes shorter as engine rpm in-
creases.

The waveforms and amplitudes displayed differ slightly
depending on the vehicle.
WAVEFORM 3
VVT OCV
ECM Terminal NameBetween OC1+ and OC1±
Between OC2+ and OC2±
Tester Range0.2 V/DIV, 200 msec./DIV
ConditionAccelerate slowly after engine warmed±up
HINT:
In the DATA LIST, the items VVT OCV DUTY B1 and B2 show
the duty ratio of voltage flowing to the OCV (see illustration on
left).
VVT OCV DUTY B1, B2 = A/B x 100 (%)
WAVEFORM 4
(a) VVT sensor bank 1
(b) VVT sensor bank 2
(c) Crankshaft position sensor
ECM Terminal Name
(a) Between VV1+ and VV1±
(b) Between VV2+ and VV2±
(c) Between NE+ and NE±
Tester Range2 V/DIV, 20 msec./DIV
ConditionIdle after engine warmed±up
HINT:
The wavelength becomes shorter as the engine rpm increases.

A23651
20 msec./DIV 5 V/DIV
(a)
(b)
Ground
Ground
A23652
10 msec./DIV 1 V/DIV
Ground
A23653
1 msec./DIV 5 V/DIV
Ground
A23654
1 msec./DIV 5 V/DIV
Ground
A23655
(a)
(b)
20 msec./DIV 2 V/DIV
Ground
Ground
DI±38
± DIAGNOSTICSENGINE
232 Author: Date:
2005 SEQUOIA (RM1146U)
WAVEFORM 5
(a) Camshaft position sensor
(b) Crankshaft position sensor
ECM Terminal Name(a) Between G2+ and G2±
(b) Between NE+ and NE±
Tester Range5 V/DIV, 20 msec./DIV
ConditionIdle after engine warmed±up
HINT:
The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 6
Vehicle speed signal
ECM Terminal NameBetween SP2+ and SP2±
Tester Range5 V/DIV, 10 msec./DIV
ConditionDriving by 40 km/h (25 mph)
HINT:
The wavelength becomes shorter as vehicle speed increases.
WAVEFORM 7
Throttle actuator positive terminal
ECM Terminal NameBetween M+ and ME01
Tester Range5 V/DIV, 1 msec./DIV
ConditionIdle after engine warmed±up
HINT:
The duty ratio varies depending on the throttle opening opera-
tion.
WAVEFORM 8
Throttle actuator negative terminal
ECM Terminal NameBetween M± and ME01
Tester Range5 V/DIV, 1 msec./DIV
ConditionIdle after engine warmed±up
HINT:
The duty ratio varies depending on the throttle opening opera-
tion.
WAVEFORM 9
(a) Igniter IGT signal (from ECM to igniter)
(b) Igniter IGF signal (from igniter to ECM)
ECM Terminal Name(a) Between IGT1 (to IGT8) and E1
(b) Between IGF1 (IGF2) and E1
Tester Range2 V/DIV, 20 msec./DIV
ConditionIdling
HINT:
The wavelength becomes shorter as vehicle speed increases.

A23656
0.2 V/DIV
200 msec./DIV
Ground
A2365710 msec./DIV 5 V/DIV
Ground
± DIAGNOSTICSENGINE
DI±39
233 Author: Date:
2005 SEQUOIA (RM1146U)
WAVEFORM 10
Heated oxygen sensor
ECM Terminal NamesBetween OX1B and E2
Tester Ranges0.2 V/DIV, 200 msec./DIV
ConditionsEngine speed maintained 2,500 rpm for 2 minutes after
warming up sensor
HINT:
In the DATA LIST, item O2S B1S2 shows the ECM input values
from the heated oxygen sensor.
WAVEFORM 11
Engine speed signal
ECM Terminal NamesBetween TACH and E1
Tester Ranges5 V/DIV, 10 msec./DIV
ConditionsIdling
HINT:
The wavelength becomes shorter as vehicle speed increases.

A04550
12 345678
11 12 13 14 15 16 910
DLC3
± DIAGNOSTICSENGINE
DI±41
235 Author: Date:
2005 SEQUOIA (RM1146U)

Freeze frame data:
The freeze frame data records the engine conditions (fuel
system, calculated load, engine coolant temperature, fuel
trim, engine speed, vehicle speed, etc.) when a malfunc-
tion is detected. When troubleshooting, freeze frame data
can help determine if the vehicle was running or stopped,
if the engine was warmed up or not, if the air±fuel ratio
was lean or rich, as well as other data from the time when
a malfunction occurred.
Priorities for troubleshooting:
When multiple DTCs occur, find out the order in which the DTCs
should be inspected by checking the component's DTC chart.
If no instructions are written in the DTC chart, check DTCs in the
following order of priority:
(a) DTCs other than fuel trim malfunction DTCs (P0171,
P0172, P0174 and P0175) and misfire DTCs (P0300 to
P0308).
(b) Fuel trim malfunction DTCs (P0171, P0172, P0174 and
P0175).
(c) Misfire DTCs (P0300 to P0308).
4. CHECK DLC3
The vehicle's ECM uses the ISO 9141±2 for communica-
tion protocol. The terminal arrangement of the DLC3 com-
plies with SAE J1962 and matches the ISO 9141±2 for-
mat.
SymbolTerminal DescriptionConditionSpecified Condition
SIL (7) ± SG (5)Bus º+º lineDuring transmissionPulse generation
CG (4) ± Body groundChassis groundAlwaysBelow 1 W
SG (5) ± Body groundSignal groundAlwaysBelow 1 W
BAT (16) ± Body groundBattery positiveAlways11 to 14 V
CANH (6) ± CANL (14)HIGH±level CAN bus lineIgnition switch OFF54 to 69 W
CANH (6) ± Battery positiveHIGH±level CAN bus lineIgnition switch OFF1 MW or higher
CANH (6) ± CG (4)HIGH±level CAN bus lineIgnition switch OFF1 kW or higher
CANL (14) ± Battery positiveLOW±level CAN bus lineIgnition switch OFF1 MW or higher
CANL (6) ± CG (4)LOW±level CAN bus lineIgnition switch OFF1 kW or higher
HINT:
Connect the cable of the hand±held tester to the DLC3, turn the
ignition switch ON and attempt to use the hand±held tester. If
the screen displays UNABLE TO CONNECT TO VEHICLE, a
problem exists in the vehicle side or the tester side.

If the communication is normal when the tool is connected
to another vehicle, inspect the DLC3 on the original ve-
hicle.

± DIAGNOSTICSENGINE
DI±45
239 Author: Date:
2005 SEQUOIA (RM1146U)
3. CLEAR DTC (Not using the hand±held tester)
(a) Remove the EFI No. 1 and ETCS fuses from the engine
room J/B for more than 60 seconds, or disconnect the bat-
tery terminal for more than 60 seconds.
After disconnecting the battery terminal, perform the ºINI-
TIALIZEº procedure.

± DIAGNOSTICSENGINE
DI±53
247 Author: Date:
2005 SEQUOIA (RM1146U)A/C SIG
A/C signal: ON or OFFON: A/C ON'
ELECT LOAD SIGElectrical load signal:
ON or OFFON: Headlights or defogger is
turned ON'
STOP LIGHT SWStop lamp switch:
ON or OFFON: brake pedal is depressed.'
+BM
Whether or not electric throttle
control system power inputted:
ON or OFF
ON: Idling'
+BM VOLTAGE+BM voltage:
Min.: 0, Max.: 19.9210 to 15 V: IdlingETCS service data
BATTERY VOLTAGEBattery voltage:
Min.: 0 V, Max.: 65.535 V9 to 14 V: Idling'
ACTUATOR POWERActuator power supply:
ON or OFFON: IdlingETCS service data
ATM PRESSUREAtmospheric pressure:
Min.: 0 kPa, Max.: 150 kPaEquivalent to atmospheric pres-
sure (absolute pressure)'
SECOND AIR VSVSecondary air injection system
statusON: Secondary air injection sys-
tem operation'
ACT VSVA/C cut status for Active Test:
ON or OFF'Active Test support data
EVAP (Purge) VSVVSV status for EVAP control:
ON or OFF'Active Test support data
FUEL PUMP / SPDFuel pump/speed status:
ON or OFF'Active Test support data
VVT CTRL B1VVT control status:
ON or OFF'Active Test support data
VVT CTRL B2VVT control status:
ON or OFF'Active Test support data
VACUUM PUMP
Key±off EVAP system pump sta-
tus:
ON or OFF
'Active Test support data
EVAP VENT VAL
Key±off EVAP system vent valve
status:
ON or OFF
'Active Test support data
TC/TE1TC and TE1 terminal of DLC3:
ON or OFF''
VVTL AIM ANGL #1VVT aim angle (bank 1):
Min.: 0 %, Max.: 100 %0 %: IdlingVVT duty signal value during intru-
sive operation
VVTL AIM ANGL #2VVT aim angle (bank 1):
Min.: 0 %, Max.: 100 %0 %: IdlingVVT duty signal value during intru-
sive operation
VVT CHNG ANGL #1VVT change angle:
Min.: 0FR, Max.: 60FR0 to 5 FR: IdlingDisplacement angle during intru-
sive operation
VVT CHNG ANGL #2VVT change angle:
Min.: 0FR, Max.: 60FR0 to 5 FR: IdlingDisplacement angle during intru-
sive operation
VVT OCV DUTY B1VVT OCV operation duty:
Min.: 0 %, Max.: 100 %0 %: IdlingRequested duty value for intrusive
operation
VVT OCV DUTY B2VVT OCV operation duty:
Min.: 0 %, Max.: 100 %0 %: IdlingRequested duty value for intrusive
operation
FC IDLFuel cut idle:
ON or OFFON: Fuel cut operation
FC IDL = ºONº when throttle valve
fully closed and engine speed over
2,800 rpm

A31449A23511
Valve Battery ±
Battery +
DI±76
± DIAGNOSTICSENGINE
270 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check OCV circuit.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and warm it up.
(c) Turn the ignition switch to ON and turn the hand±held tester ON.
CHECK:
(a) Select the item: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1 or VVT CTRL B2.
(b) Using the hand±held tester, operate the OCV and check the engine speed.
OK:
Standard:
Tester OperationSpecified Condition
OCV is OFFNormal engine speed
OCV is ONRough idle or engine stall
OK Check for intermittent problems
(See page DI±11).
NG
2 Check operation of OCV.
PREPARATION:
(a) Start the engine and warmed it up.
(b) Disconnect the OCV connector.
(c) Apply battery positive voltage between the terminals of
the OCV.
CHECK:
Check the engine speed.
OK:
Rough idle or engine stalled.
NG Replace OCV.
OK

A02397
OCV Signal Waveform
1 msec./Division5 V/
Division
GND
(A) (A) (A)
B17414ECM ConnectorE6
OC1+
OC1±
OC2+OC2±
E1
± DIAGNOSTICSENGINE
DI±77
271 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check voltage between terminals OC1+ and OC1±, OC2+ and OC2± of ECM con-
nector.
CHECK:
(a) Inspection using the oscilloscope.
(b) During idling, check the waveform between the specified
terminals of the E6 ECM connector.
HINT:
The waveform frequency (A) is lengthened as the engine speed
becomes higher.
OK:
Standard:
The correct waveform is as shown.
NG Replace ECM (See page SF±80).
OK

A23673
Wire Harness Side
C13
OCV Connector C14
B17414ECM ConnectorE6
OC1+
OC1±
OC2+OC2±
E1
DI±78
± DIAGNOSTICSENGINE
272 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check for open and short in harness and connector between OCV and ECM.
PREPARATION:
(a) Disconnect the C13 or C14 OCV connector.
(b) Disconnect the E6 ECM connector.
CHECK:
(a) Check for resistance between the wire harness side con-
nectors.
OK:
Standard (Check for open):
Symbols (Terminal No.)Specified condition
OCV (C14±1) ± OC1+ (E6±17)Below 1 W
OCV (C14±2) ± OC1± (E6±16)Below 1 W
OCV (C13±1) ± OC2+ (E6±15)Below 1 W
OCV (C13±2) ± OC2± (E6±14)Below 1 W
Standard (Check for short):
Symbols (Terminal No.)Specified condition
OCV (C14±1) or OC1+ (E6±17) ± E1 (E6±1)10 kW or higher
OCV (C14±1) or OC1± (E6±16) ± E1 (E6±1)10 kW or higher
OCV (C13±1) or OC2+ (E6±15) ± E1 (E6±1)10 kW or higher
OCV (C13±1) or OC2± (E6±14) ± E1 (E6±1)10 kW or higher
NG Repair or replace harness or connector.
OK
Check for intermittent problems
(See page DI±11).