rear view mirror TOYOTA SEQUOIA 2001 Service Owner's Manual

05_SEQUOIA_U (L/O 0408)
137
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
CAUTION

Do not adjust the mirror while the
vehicle is moving. Doing so may
cause the driver to mishandle the
vehicle and an accident may occur
resulting in death or injuries.

On some models, since the mirror
surfaces can get hot, do not touch
them when the defogger switch is
on.
Ty p e A
Ty p e B
To adjust a mirror, use the switches.
1. Master switchÐTo select the mirror to
be adjusted
Push the switch to ªLº (left) or ªRº
(right).
2. Control switchÐTo move the mirror
Push the switch in the desired direc-
tion.
Mirrors can be adjusted when the key is
in the ªACCº or ªONº position.
Vehicles with the driving position memory
systemÐThe position of the outside rear
view mirrors and driver's seat can be
memorized. For details, see ªDriving posi-
tion memory systemº on page 71 in Sec-
tion 1±3.
NOTICE
If ice should jam the mirror, do not
operate the control or scrape the mir-
ror face. Use a spray de±icer to free
the mirror.
ÐPower rear view mirror
control

05_SEQUOIA_U (L/O 0408)
138
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
FOLDING MIRRORS (type A only)
To fold mirrors for parking in restricted
areas, push the mirror folding button.
The key must be in the ªACCº or ªONº
position.
Position 1ÐTo fold the mirrors
Position 2ÐTo return the mirrors back to
their original positions
CAUTION
To avoid personal injury and any mir-
ror malfunction, do not touch the mir-
ror while it is moving.
The rear view mirrors can be folded
backward for parking in compact areas.
To fold the rear view mirror, push back-
ward.
Vehicles with power mirror folding button
onlyÐ
If the key is turned from ªLOCKº to ªACCº
the mirror will move automatically accord-
ing to the position of the mirror folding
button.
CAUTION
Do not drive with the mirrors folded
backward. Both the driver and pas-
senger side rear view mirrors must
be extended and properly adjusted
before driving.
ÐFolding rear view mirrors

05_SEQUOIA_U (L/O 0408)
139
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Adjust the mirror so that you can just
see the rear of your vehicle in the mir-
ror.
To reduce glare from the headlights of
the vehicle behind you during night
driving, operate the lever on the lower
edge of the mirror.
Daylight drivingÐLever at position 1
The reflection in the mirror has greater
clarity at this position.
Night drivingÐLever at position 2
Remember that by reducing glare you also
lose some rear view clarity.
CAUTION
Do not adjust the mirror while the
vehicle is moving. Doing so may
cause the driver to mishandle the ve-
hicle and an accident may occur re-
sulting in death or injuries.
Adjust the mirror so that you can just
see the rear of your vehicle in the mir-
ror.
This mirror is equipped with auto anti±
glare function. The function is designed
to reduce glare from the headlights of
the vehicle behind you during night
driving.
When the ignition key is inserted and
turned on, the inside rear view mirror al-
ways turns on in the automatic function
mode.
The indicator illuminates to show you that
the function is on.
Anti±glare inside rear view
mirrorAuto anti±glare inside rear
view mirror

05_SEQUOIA_U (L/O 0408)
140
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
In automatic function mode, if the mirror
detects light from the headlights of the
vehicle behind you, the mirror surface
darkens slightly to reduce the reflected
light.
To turn off the automatic function, press
the switch on the ªOFFº side.
To turn on the automatic function again,
press the switch on the ªAUTOº side.
Adjust it before driving so that the rear
view is in the best condition.
When the outside air temperature is low,
it may take a little longer for the mirror
to darken in response to the detection of
headlights.
CAUTION
Do not adjust the mirror while the
vehicle is moving. Doing so may
cause the driver to mishandle the ve-
hicle and an accident may occur re-
sulting in death or serious personal
injuries.
To ensure correct functioning of anti±
glare mirror sensors located on both
sides of the mirror, do not touch or
cover the sensors with your finger or
a piece of cloth, etc.To block out glare, move the sun visor.
To block out glare from the frontÐSwing
down the sun visor (position 1).
To block out glare from the sideÐSwing
down the sun visor, remove it from the
hook and swing it to the lateral side (posi-
tion 2).
If glare comes from obliquely behind you,
extend the plate at the end of the visor
(to position 3).
Sun visorsÐ

05_SEQUOIA_U (L/O 0408)
141
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
To block the glare from the front when the
main sun visor is swung to the lateral
side (position 2), swing down the sub vi-
sor.
CAUTION
Do not extend the plate at the end of
the sun visor when the visor is in the
position 1. It can cover the anti±glare
inside rear view mirror and obstruct
the rear view.
To use the vanity mirrors, swing down
the sun visor and open the cover.
On some models, the vanity light comes
on when you open the cover.
ÐVanity mirrors

05_SEQUOIA_U (L/O 0408)
143
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
OPERATION OF INSTRUMENTS AND
CONTROLS
Lights, Wipers and Defogger
Headlights and turn signals144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency flashers148 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument panel light control148 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front fog lights149 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Personal lights149 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Center interior and personal lights150 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Center interior light151 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage compartment light152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch light152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield wipers and washer153 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back window wiper and washer154 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back window and outside rear view mirror defoggers154 . . . . . . . . . . .
SECTION 1± 5

05_SEQUOIA_U (L/O 0408)
154
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
To turn on the back window wiper, twist
the lever knob upward.
The key must be in the ªONº position.
Lever position
Speed setting
Position 1Intermittent
Position 2Normal
To squirt washer fluid on the back window,
twist the knob upward or downward as far
as it will go (position 3 or 4).
The wiper is activated after the washer
squirts fluid if you twist the knob upward.
But, the washer only squirts fluid if you
twist the knob downward.The knob automatically returns from these
positions after you release it.
For instructions on adding washer fluid,
see ªAdding washer fluidº on page 444 in
Section 7±3.
If the back window is not fully closed, the
back window wiper and washer will not
work. Make sure the back window is fully
closed when using the back window wiper
and washer.
NOTICE
Do not operate the back window wip-
er if the back window is dry. It may
scratch the glass.To defog or defrost the back window,
push the switch with the back window
closed.
The key must be in the ªONº position.
The thin heater wires on the inside of the
back window will quickly clear the surface.
An indicator light will illuminate to indicate
the defogger is operating.
On some models, heater panels in the
outside rear view mirrors will also quickly
clear the surfaces.
Push the switch once again to turn the
defogger off.
The system will automatically shut off af-
ter the defoggers have operated about 15
minutes.
Back window wiper and
washerBack window and outside rear
view mirror defoggers

05_SEQUOIA_U (L/O 0408)
362
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
1. Check the area around the vehicle be-
fore entering it.
2. Adjust seat position, seatback angle,
seat cushion angle, head restraint
height and steering wheel angle.
3. Adjust the inside and outside rear view
mirrors.
4. Lock all doors.
5. Fasten seat belts.Once you turn the ignition key to ªSTARTº
position and release it, the cranking hold
function continues to crank the engine in
ªONº position until it starts.
The function stops cranking the engine
after about 25 seconds maximum if the
engine has not started yet. When you
crank the engine again, wait a few sec-
onds and restart it.
If you hold the key in ªSTARTº position,
the function will keep cranking for about
30 seconds maximum.1. Apply the parking brake firmly.
2. Turn off unnecessary lights and acces-
sories.
3. Put the selector lever in ªPº. If you
need to restart the engine while the
vehicle is moving, put the selector le-
ver in ªNº. A starter safety device will
prevent the starter from operating if the
selector lever is in any drive position.
4. Depress the brake pedal and hold it to
the floor until driving off.
Before starting the engineHow to start the engineÐ
ÐCranking hold function(a) Before cranking

05_SEQUOIA_U (L/O 0408)
375
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
MAINTENANCE

If you tow a trailer, your vehicle will
require more frequent maintenance due
to the additional load. For this informa-
tion, please refer to the scheduled
maintenance information in the ªSched-
uled Maintenance Guideº or ªOwner 's
Manual Supplementº.

Retighten all fixing bolts of the towing
ball and bracket after approximately
1000 km (600 miles) of trailer driving.
CONNECTING A TRAILER (models with
rear height control air suspension)
Stop your vehicle and a trailer in line and
perform the following:
1. Set the vehicle height to ªNº (normal)
in automatic control mode. Turn the
ignition switch off or select manual
control mode by pushing the mode se-
lect switch to turn off the automatic
leveling function.
2. Connect a trailer.
3. Turn the ignition switch on or select
automatic control mode by pushing the
mode select switch to turn on the auto-
matic leveling function.DISCONNECTING A TRAILER (models
with rear height control air suspension)
Stop your vehicle and a trailer in line and
perform the following:
1. Set the vehicle height to ªLOº in auto-
matic control mode. (Make sure the
ªLOº indicator comes on.)
2. Turn the ignition switch off or select
manual control mode by pushing the
mode select switch to turn off the auto-
matic leveling function.
3. Set the supporting leg of a trailer on
the ground and raise the hitch by 100
mm (4 in.).
4. Turn the ignition switch on or select
automatic control mode by pushing the
mode select switch to turn on the auto-
matic leveling function.
5. Wait for about 20 seconds until the
rear vehicle height is lowered by the
automatic leveling function.
6. Make sure the hitch is disconnected. If
not, raise the hitch higher and repeat
steps 2 through 5.
7. Move the vehicle forward in ªLOº mode
where the hitch does not touch any-
thing in ªNº mode.
8. Set the vehicle height to ªNº in auto-
matic control mode.PRE±TOWING SAFETY CHECK

Check that your vehicle remains level
when a loaded or unloaded trailer is
hitched. Do not drive if the vehicle has
an abnormal nose±up or nose±down
condition, and check for improper
tongue load, overload, worn suspension
or other possible causes.

Make sure the trailer cargo is securely
loaded so that it cannot shift.

Check that your rear view mirrors con-
form to any applicable federal, state/
provincial or local regulations. If not,
install the rear view mirrors required
for towing purpose.

05_SEQUOIA_U (L/O 0408)
459
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Engine compartment
Fuses (type A)
1. AIR SUS No.2 10 A: Rear height con-
trol air suspension system
2. RSE 7.5 A: Rear seat audio system,
rear seat entertainment system
3. A/F 20 A: A/F sensor
4. SECURITY 15 A: Multiplex communica-
tion system
5. DEF I/UP 7.5 A: Rear window defog-
ger, outside rear view mirror defoggers,
multiport fuel injection system/sequen-
tial multiport fuel injection system
Engine compartment
6. H±LP LL 10 A (with daytime running
light system): Left±hand headlight (low
beam)
7. H±LP RL 10 A (with daytime running
light system): Right±hand headlight
(low beam)
8. STA 7.5 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system, electronic throttle control sys-
tem
9. H±LP LH 10 A (with daytime running
light system): Left±hand headlight
(high beam)
Engine compartment
10. H±LP RH 10 A (with daytime running
light system): Right±hand headlight
(high beam)
11. TOWING TAIL 30 A: Trailer lights (tail
lights)
12. BATT CHARGE 30 A: Trailer sub bat-
tery
13. TOWING BRK 30 A: Trailer brake con-
troller
14. CDS FAN 25 A: Electric cooling fan
15. SPARE 15 A: Spare fuse
16. SPARE 20 A: Spare fuse
17. SPARE 30 A: Spare fuse
Fuses