reset TOYOTA SEQUOIA 2001 Service Owner's Manual

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±829
1023 Author: Date:
2005 SEQUOIA (RM1146U)
4 Forcibly transmit transmitter ID.
PREPARATION:
(a) Forcibly transmit the transmitter ID by performing the following:
(1) Set the tire pressure to the specified value.
(2) Rotate the tire 90 to 270 degrees.
(3) Rapidly reduce the pressure of all tires to 120 kPa (1.2 kgf/cm
2, 17 psi respectively).
(4) Perform the steps mentioned above to all tires including the spare tire.
NEXT
5 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
HINT:
A system error is probable if NG. If any DTC other than C2111/21, C2112/22, C2113/23, C2114/24 and
C2115/25, is output, perform troubleshooting according to that DTC.
OK Set tire pressure to normal value (Transmitter
stop condition is completely reset).
NG
6 Check DTC (See page DI±820).
CHECK:
Check if DTCs C2111/21, C2112/22, C2113/23, C2114/24 and C2115/25 are all output.
No Go to step 12.
Ye s

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±863
1057 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check tire pressure warning lamp.
PREPARATION:
(a) Turn the ignition switch to the ON position.
(b) Enter TEST MODE (see page DI±810).
(c) Press the tire pressure warning reset switch for 1 second or more after switching to TEST MODE.
CHECK:
Does the tire pressure warning lamp come on while pressing the tire pressure warning reset switch?
RESULT:
Comes onA
Does not come onB
B Go to step 14.
A

F19884
Tire Pressure Warning Reset Switch
(harness side connector)
Tire Pressure Monitor ECU:T18
CALSW
T17
F19144
Tire Pressure Warning Reset Switch
ON
OFF2
1
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±867
1061 Author: Date:
2005 SEQUOIA (RM1146U)
14 Check harness and connector (Tire pressure warning reset switch ± Tire pres-
sure monitor ECU).
PREPARATION:
Disconnect the tire pressure warning reset switch connector
T18 and tire pressure monitor ECU connector T17.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
T17±10 (CALSW) ± T18±1Below 1 W
T17±10 (CALSW) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
15 Inspect tire pressure warning reset switch.
PREPARATION:
Disconnect the tire pressure warning reset switch connector.
CHECK:
Measure the resistance between terminals 1 and 2 of the tire
pressure warning reset switch when the tire pressure warning
switch is ON and OFF.
OK:
Switch ConditionSpecified Condition
ONBelow 1 W
OFF10 kW or higher
NG Replace tire pressure warning reset switch.
OK

F19790
Combination MeterTire Pressure
Monitor ECU
Engine Room J/B I18
Ignition SWIGN1
B±O
IG2AM2 1C11
Battery 2
1HT17
C5GR±L
Tire Pressure
B±R
B 56
54AM2 24
6IND Instrument Panel J/B
C620
2D1
2C1 1C3
1J7
F10
Fusible Link BlockInstrument Panel J/B
W±R
W±R
B
T17 T18 Tire Pressure
Warning Reset SW
G±R
CALSW
GND
T17 1H
1H
1F7
1 10
W±B11 10 Instrument Panel J/B
W±B
A J8
J/C
IE1 2
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±875
1069 Author: Date:
2005 SEQUOIA (RM1146U)
Tire Pressure Warning Reset Switch Circuit
CIRCUIT DESCRIPTION
Receiving the signal from the tire pressure warning reset switch, the tire pressure monitor ECU indicates the
initialization of the pressure warning system.
WIRING DIAGRAM
DIDKG±01

F19144
Tire Pressure Warning Reset Switch
ON
OFF2
1
DI±876
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1070 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure monitor valve sub±assy and/or
tire pressure monitor ECU (see page DI±805).
1 Check tire pressure warning reset switch function.
CHECK:
Perform the tire pressure warning reset switch test in TEST MODE PROCEDURE (see page DI±810).
OK:
Reset switch ON: Tire pressure warning lamp comes on.
Reset switch OFF: Tire pressure warning lamp blinks.
NG Go to step 2.
OK
End.
2 Inspect tire pressure warning reset switch.
PREPARATION:
Disconnect the tire pressure warning reset switch connector.
CHECK:
Measure the resistance between terminals 1 and 2 of the tire
pressure warning reset switch when the tire pressure warning
switch is ON and OFF.
OK:
Switch ConditionSpecified Condition
ONBelow 1 W
OFF10 kW or higher
NG Replace tire pressure warning reset switch.
OK

F19884
Tire Pressure Warning Reset Switch
(harness side connector)
Tire Pressure Monitor ECU:T18
CALSW
T17
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±877
1071 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check harness and connector (Tire pressure warning reset switch ± Tire pres-
sure monitor ECU)
PREPARATION:
Disconnect the tire pressure warning reset switch T18 connec-
tor and tire pressure monitor ECU T17 connector .
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
T17±10 (CALSW) ± T18±1Below 1 W
T17±10 (CALSW) ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Replace tire pressure monitor ECU
(See page SA±20).

H24658
Ignition SwitchON
OFF
RSCA OFF SwitchOFF
ON
RSCA OFF IndicatorON
OFFApprox.
3 secondsApprox.
2 secondsApprox.
2 seconds
Bulb Check
(SW input signal prohibited)
Approx.
0.2 secondsApprox.
0.2 seconds
H23823
DI±1142
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1336 Author: Date:
2005 SEQUOIA (RM1146U)
5. FUNCTION RSCA OFF INDICATOR
(a) The RSCA OFF indicator comes on for approximately 3 seconds after the ignition switch is turned ON,
then goes off.
(b) Approximately 3 seconds after the turning the ignition switch ON, the RSCA OFF indicator comes on
or goes off every time it detects OFF (press the switch for approximately 0.2 seconds) or ON (press
the switch for approximately 2 seconds).
HINT:
The RSCA OFF switch is reset by turning the ignition switch to the LOCK position.
As a result, the RSCA OFF switch and RSCA OFF indicator are off when the ignition switch is turned to the
ON position.
6. CHECK SRS WARNING LIGHT
(a) Turn the ignition switch to the ON position, and check that
the SRS warning light comes on for approximately 6 se-
conds (primary check).
(b) Check that the SRS warning light goes off approximately
6 seconds after the ignition switch is turned to the ON
position (constant check).
HINT:
When any of the following symptoms occur, refer to the ºProb-
lem Symptoms Tableº (see page DI±1132).

The ignition switch is turned from the LOCK to ON posi-
tion, but the SRS warning light does not come on.

The SRS warning light comes on occasionally after the
primary check period has elapsed.

The SRS warning light comes on, but DTC is not output.

I24838
(4)(1)
(3)
I24838
(5)
(1)
(3)
DI±1540
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1734 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Inspect the CANCEL function.
(1) Push the ON±OFF button on.
(2) Drive at the required speed (40 km/h (25 mph) or
higher).
(3) Push the cruise control main switch to ±/SET.
(4) When doing any one of the following, check that the
cruise control system deactivates and that the nor-
mal driving mode is reset.

Depressing the brake pedal

Moving the shift lever to any position except
D

Pushing the ON±OFF button off

Pulling the cruise control main switch to CAN-
CEL
Reference: Cruise control will deactivate if VSC starts op-
eration while driving.
(e) Inspect the RES (RESUME) function.
(1) Push the ON±OFF button on.
(2) Drive at the required speed (40 km/h (25 mph) or
higher).
(3) Push the cruise control main switch to ±/SET.
(4) When doing any one of the following, check that the
cruise control system deactivates and that the nor-
mal driving mode is reset.

Depressing the brake pedal

Moving the shift lever to any position except
D

Pulling the cruise control main switch to CAN-
CEL
(5) After pushing the cruise control main switch to
+/RES while driving, check that the vehicle resumes
the speed set prior to the cancellation.

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1609
1803 Author: Date:
2005 SEQUOIA (RM1146U)A/T R
Receives an R signal from the park/neutral position switch (Direct line)±
TAIL/HEADReceives a dimmer signal from the body ECU (BEAN)±
TIRE PRESSUREReceives a low tire pressure signal from the tire pressure monitor ECU (Direct line)
4LOReceives a 4LO signal from the 4WD control ECU (Direct line)±
MAIN REQD (Blinks)Blinks when 4,500 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
MAIN REQD (Comes on)Blinks when 5,000 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
RSCA OFFReceives an RSCA OFF signal from the airbag sensor center (Direct line)
HIReceives a suspension position HI signal from the suspension control ECU (Direct
line)
NReceives a suspension position N signal from the suspension control ECU (Direct
line)
LOReceives a suspension position LO signal from the suspension control ECU (Direct
line)
AHC MAN.Receives a suspension control manual signal from the suspension control ECU
(Direct line)
*1: w/ Day time running light
*2: w/o Day time running light
BUZZER:
ItemDetail
Key ReminderBuzzer is ON: Ignition switch is OFF, key is inserted, and door is open.
Fasten BeltBuzzer is ON: Ignition switch is ON and seat belt is unfastened.
2. COMBINATION METER IN SEQUOIA HAS THE FOLLOWING FEATURES:
(a) Built±in buzzer for the reminder system (key and seat belt)
(b) Integrated trip and odometer knobs

Press and release knob to scroll through trip ºAº, trip ºBº, and odometer features.

Press and hold the trip knob to reset trip meter functions.
(c) Oil maintenance indicator

When 4,500 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor begins to blink for 15 seconds after the ignition switch is turned to the ON position.

When 5,000 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor comes on.

Press and hold the trip knob to reset the oil maintenance indicator.
(d) Rotate knob to adjust interior illumination

DID9S±01
I24383
º1chº Switch
ºSEEK TRACKº
DOWN SwitchºSEEK TRACKº
UP SwitchºDISCº Switch º2chº Switchº3chº Switch
º4chº Switchº5chº Switch
º6chº Switch
DI±1974
± DIAGNOSTICSAUDIO SYSTEM
2168 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
1. DIAGNOSTIC CHECK
(a) Starting Diagnostic Mode (All elements come on during the SW check mode).
(1) Turn off the audio system and turn the ignition switch to the ACC position. While pressing the
preset switches º1º and º6º at the same time, press the ºDISCº 3 times.
(2) Reference:
When the system enters the Diagnosis Mode, a beep sound is emitted 3 times and all the
elements come on during the SW check mode.
It takes about 40 seconds to complete the check.
Turn all the elements in the LCD on.
When pressing the switch, confirm beep sound is emitted.
(b) Service Check Screen.
(1) Press the ºSEEK TRACKº switch to enter the ºService Check Screenº.
(2) In the service check mode, the system check and the diagnostic memory check are performed,
and the check results are displayed in ascending order of the component codes (physical ad-
dress.)
TermsMeaning
Component code
(Physical address)Three±digit code (In hexadecimal) given to each device comprising AVC±LAN.
Corresponding to its function, individual symbol is provided.
Logical addressTwo±digit code (In hexadecimal) given to each function and device unit in each
device comprising AVC±LAN.
Code No. (physical address) List
Code No.
(physical address)Equipment name
190Radio receiver assy (Audio head unit)
440Stereo component amplifier assy
1F6Multi±display controller (RSE ECU)
1F4Rear seat audio controller
(c) Finishing Diagnostic Mode.
Press the ºDISCº for 2 seconds or more, or turn the ignition switch off.