Wiring TOYOTA SEQUOIA 2001 Service Owner's Guide

A23551
Engine Room J/BECM
E4
E4
E4
E4 B±W
IA4
IA4
IA4
IA4
IA4
EB4 ED2
ED2B±W
2H
2A68
EFI Relay
2 1
2F
1 W±B
J5
J/C A
ED
Battery Air Pump Air Switching Valve Air Injection Driver
A43 A46A415
G±RG±R
J2
J/C
A
A EFI No.2 EFI No.1
3 52
2D1
B
4F10
FL Block
5B L
A401
EN B B
B 1
12
2 W
W±L W±L
W
34 2
6 A40
A41A41
A41
A41
A411 2 43
1
8
EBW±BW±B W±B
BATT
VP
VV
E SIP
DI SIV+B
R±W
R±W 8
3
9 G±W G±W
GR±L GR±L4
25
13
AIDAIRPAIRV
A/PUMP
2MREL
14 DI±320
± DIAGNOSTICSENGINE
514 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

B17426
± DIAGNOSTICSENGINE
DI±333
527 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
Refer to DTC P1441, P1444 and P2440 on page DI±314.
INSPECTION PROCEDURE
1 Check any other DTCs output (In addition to secondary air injection system
DTCs).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
ºP1442 and/or P1445º and P2441A
P1442 and/or P1445B
ºP1442 and/or P1445 and/or P2441º and other DTCsC
HINT:
If any DTCs other than P1441 and/or P1444 and P2440 are output, troubleshoot those DTCs first.
B Go to step 6.
C Go to DTC chart (See page DI±58).
A
2 Check vacuum hose between throttle body and VSV for air injection control.
CHECK:
(a) Check that the vacuum hoses between the throttle body
and VSV for air injection control are securely connected.
OK:
The vacuum hoses are securely connected.
CHECK:
(a) Check the vacuum hoses for blockage or damage.
OK:
The vacuum hoses are no blockages and damage.
NG Repair or replace vacuum hoses.
OK

B17411
ECM Connector
E1AIDI
A16555
AIR INJ CHECK
AIR PUMP............................ON
EASV ............................OPEN
ASV1. .............................OPEN
ASV2...............................OPEN
A/F BANK1.......................19.05
A/F BANK2.......................19.05
PRESSURE....................17 kPa
PULSATION..............25.39 kPa
AI STATUS...........................OK
Remaining Time 05 sec.
Press [EXIT] to quit
± DIAGNOSTICSENGINE
DI±345
539 Author: Date:
2005 SEQUOIA (RM1146U) Case 3:
Diagnostic signal duty ratio from air injection driver0 %
Case 4:
Diagnostic signal duty ratio from air injection driver100 %
COMPONENT OPERATING RANGE
ParameterStandard Value
Diagnostic signal duty ratio from air injection driver
70 to 90% when secondary air injection system operating
and
0% when secondary air injection system not operating
WIRING DIAGRAM
Refer to DTC P0412 on page DI±234.
INSPECTION PROCEDURE
HINT:
The diagnostic information output from the AID can be confirmed by connecting an oscilloscope to the diag-
nostic information terminal of the AID. It narrows a trouble area search to read the waveform on the oscillo-
scope when performing the AI system intrusive operation function provided in the SYSTEM CHECK.
(a) Start the engine and warm it up.
(b) Turn the ignition switch to OFF.
(c) Connect a hand±held tester to the DLC3.
(d) Connect an oscilloscope probe to the AIDI terminal of the
ECM.
(e) Start the engine and turn the tester ON.
(f) On the tester, select the following menu items:
DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK /
AIR INJ SYSTEM.
(g) On the tester, select the following menu items:
DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK /
AIR INJ CHECK / MANUAL OPERATION / OPERATION
1 and 2.
HINT:
OPERATION 1: AP: OFF, EASV:CLOSE, ASV1:CLOSE,
ASV2:OFF
OPERATION 2: AP: ON, EASV:OPEN, ASV1:OPEN,
ASV2:OPEN

± DIAGNOSTICSENGINE
DI±355
549 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
RltdDTC
P2102Throttle actuator control motor current
(Low current)
Related DTCs
P2103Throttle actuator control motor current
(High current)
Required sensors/componentsThrottle actuator motor
Frequency of operationContinuous
Duration2 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
P2102:
Throttle motorON
Duty±cycle ratio to open throttle actuator80%±
Throttle actuator power supply8 V±
Current motor current ± Motor current at
0.016 sec. before±0.2 A
P2103:
Throttle motorON
Either of the following conditions is met:Condition 1 or 2
1. Throttle actuator power supply8 V±
2. Throttle actuator powerON
Battery voltage8 V±
StarterOFF
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
P2102:
Throttle motor currentLess than 0.5 A (when motor drive duty 80% or more)
P2103:
Throttle motor currentMore than 10 A (0.1 sec.)
More than 7 A (0.6 sec.)
WIRING DIAGRAM
Refer to DTC P0120 on page DI±127.

± DIAGNOSTICSENGINE
DI±359
553 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
RltdDTCP2111Throttle motor actuator lock (Open)Related DTCsP2112Throttle motor actuator lock (Closed)
Rid / tMain sensors/componentsThrottle actuator motorRequired sensors/componentsRelated sensors/componentsThrottle position sensor
Frequency of operationContinuous
Duration0.5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
P2111:
Throttle motor current2 A±
Throttle motor duty to close side80%±
P2112:
Throttle motor current2 A±
Throttle motor duty to open side80%±
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
|Current throttle position sensor voltage at this time ± throttle
position sensor voltage 0.016 sec. earlier|Less than 0.1 V when throttle motor open (or close) duty 80% or more
WIRING DIAGRAM
Refer to DTC P0120 on page DI±127.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.

A05652A18100
ECM
+BM
E47
W±G
Battery2H3 ETCS
2D1Engine Room J/B
B
IA413
W±G
4
F10
Fusible Link
Block
5
B DI±364
± DIAGNOSTICSENGINE
558 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

DI±368
± DIAGNOSTICSENGINE
562 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Difference between ºtarget throttle positionº and ºactual
throttle positionº0.3 V or more
COMPONENT OPERATING RANGE
Standard Value
Commanded throttle position and current throttle position are nearly the same
WIRING DIAGRAM
Refer to DTC P2102 and P2103 on page DI±354.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P2119) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
P2119A
ºP2119º and other DTCB
HINT:
If any other codes besides P2119 are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI±58).
A

A19759
A37
Accelerator Pedal Position Sensor
VPA1
EP1
VCP1G±W
L±YECM
E4
2119
VPA2
EP2
VCP26
5
4
3
2
1G±R
G±B
L±B
L±RE4
E4
E4
E4
E426
27 18
20
VCP2 EPA2 VPA2 VCPAEPAVPA
± DIAGNOSTICSENGINE
DI±375
569 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

FI7052DepressedReleased
± DIAGNOSTICSENGINE
DI±381
575 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Either of the following conditions is metCondition 1 or 2
1. Ignition switchON
2. Throttle control motor powerON
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Difference between VPA1 voltage (learned value) and VPA2
voltage (learned value)Less than 0.4 V, or more than 1.2 V
WIRING DIAGRAM
Refer to DTC P2120 on page DI±370.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Connect hand±held tester, and read the voltage for accelerator pedal position
sensor data.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tes-
ter main switch ON.
(c) Enter the following menu: DIAGNOSIS / ENHANCED
OBD II / DATA LIST / ETCS / ACCEL POS #1 and ACCEL
POS #2.
CHECK:
Read the voltage for the accelerator pedal position sensor data.
OK:
Standard:
Accelerator pedalACCEL POS #1ACCEL POS #2
Released0.5 to 1.1 V1.2 to 2.0 V
Depressed2.6 to 4.5 V3.4 to 5.3 V
OK Replace ECM (See page SF±80).
NG

A23547
2
A1A± MREL
HA2A
A1A+ECM
22
30 B±W
E4
E7
E7 E7
BR W±B
2EFI Relay
A39 A/F Sensor
(Bank 2 Sensor 1)
J42
J/C Engine Room R/B No. 2
W 114
F10
FL
Block
Battery
ED(Shielded)8
EB 3
2HT
AF+ +B
B
E77
E04 2IA4
5
L±R G±R
2
G±B
2
B 1
B1
4
BRB±W
W±B 2F
A/F 1
1 12 Engine Room R/B and J/B
2D
2A2H
26
EFI No. 1 EFI No. 2
22
W±BA/F Relay
1 2
3
5A
AJ2
J/C
G±R
15
IA51
IG4
(Shielded)
G
R
ECE
ECCC
J42
J/C J5
J/CJ2
J/C B
B 5Engine
Room
R/B No. 2R±W
R±W
R±W
R±W
A38 A/F Sensor
(Bank 1 Sensor 1)
+B AF±
HT
AF+
AF±1
3 2
4
1
3 2
4 R±WL31
E7 23
E7 E7
A2A+
A2A±
HA1A B
R/B
± DIAGNOSTICSENGINE
DI±389
583 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM