engine TOYOTA SEQUOIA 2001 Service Repair Manual

F19443
Height Control
Compressor
H131
Engine Room R/B No. 2
G±Y AIR SUS Relay
Battery J28
J/C W
BM21
IC48
IA121
WWW
2
22
2 3
25
1W
9B
5
W±B
J8
J/C
AAW±B
1K12
1F9
A W±B
IESuspension
Control
ECU
IA125
G±Y
S255
RC F10
Fusible Link Block
ALT
Instrument
Panel J/BAIR SUS DI±748
± DIAGNOSTICSAIR SUSPENSION SYSTEM
942 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

F19458
DI±750
± DIAGNOSTICSAIR SUSPENSION SYSTEM
944 Author: Date:
2005 SEQUOIA (RM1146U)
2 Inspect AIR SUS relay.
PREPARATION:
Remove the AIR SUS relay from the engine room R/B No. 2.
CHECK:
Check continuity between each terminal of the AIR SUS relay.
OK:
Tester connectionResistance
3 ± 510 kW or higher
3 ± 5
Below 1 W
(When battery voltage is applied to ter-
minals 1±2)
NG Replace AIR SUS relay.
OK

F16805
S25
Suspension Control ECU
Wire Harness View:
RC
F19460
Engine Room R/B No. 2:
AIR SUS
Relay Terminal
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±751
945 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check harness and connector (Engine room R/B ± Suspension control ECU,
Body ground).
PREPARATION:
Disconnect the ECU connector.
CHECK:
Check for an open or short circuit in the harness and the con-
nector between the AIR SUS relay terminal 1 of the engine
room R/B and terminal S25±5 (RC) of the suspension control
ECU.
OK:
There is no open or short in the wire harness.
CHECK:
Check for an open circuit in the harness and the connector be-
tween the AIR SUS relay terminal 2 of the engine room R/B and
body ground.
OK:
There is no open in the wire harness.
NG Repair or replace harness or connector.
OK
Replace suspension control ECU
(See page IN±35).

F19444
Height Control Compressor
(Compressor/Height Control Dryer)
H133
Engine Room R/B No. 2
W±B
Battery J28
J/CR±L
BM23
IN115
S2520
2
3
25
1W
9B
5
J8
J/C
AAW±B
1K12
1F9
A W±B
IESuspension
Control
ECU
RC F10
Fusible Link Block
AIR SUS
Instrument
Panel J/BRM+ R±L R±L
H134
BR±Y
BM24
IA121S2521
BR±Y BR±Y
RM±
AIR SUS Relay H131
W
BM21
IC48
WW W
22
2 S255
G±Y IN16
IA125
G±Y
BJ H132
BM22
W±B
AJ19
J/C W±BALT
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±753
947 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

F19461
Height Control Compressor
Connector Front View:
H13
DI±756
± DIAGNOSTICSAIR SUSPENSION SYSTEM
950 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check harness and connector (Height control compressor ± Battery, Body
ground).
PREPARATION:
(a) Reconnect the ECU connector.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage according to the value(s) in the table be-
low.
OK:
Tester connectionConditionSpecified value
H13±1 ± Body ground
Engine idling, height con-
trol switch is pushed from
ºNº to ºUPº
10 to 14 V
HINT:
Measure the voltage within 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified value
H13±2 ± Body groundAlwaysBelow 1 W
NG Repair or replace harness or connector.
OK
Replace suspension control ECU
(See page IN±35).

± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±757
951 Author: Date:
2005 SEQUOIA (RM1146U)
DTC C1751/51 Continuous Electric Current To Height Con-
trol Compressor
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
C1751/51*1With the AIR SUS relay activated, the vehicle does not go up
to the standard vehicle height after the 90 sec. have elapsed.

Height control compressor assy

Height control compressor circuit

Height control sensor circuit

Height control sensor sub±assy

Relief valve

AIR SUS relay circuit

Air leakage from the air tube or each valve

Clogging in the air tube or each valve

Suspension control ECU
*1: The compressor motor operates continuously to raise vehicle height and allows electric current flow to
the AIR SUS relay for 90 seconds or more under the following conditions:

Vehicle height control is attempted on a steep slope when the vehicle is overloaded.

The compressor remains on for an excessive period of time or repeatedly turns on and off because
of continuous height control switch operation.

If the compressor remains on because the vehicle is jacked up, the vehicle height is set at a position
lower than normal while the engine is running and then the vehicle height control function raises the
vehicle.
Thus DTC C1751/51 may be output and vehicle height control may be suspended. (This is not electrically
abnormal.) In this case, however, the vehicle height operation is resumed approx. 10 min. after the ignition
switch is turned ON after the ECU detects the first error. If ECU detects another error, it takes 70 minutes
until control is resumed.
WIRING DIAGRAM
See page DI±752.
DIDDV±01

F19445
Engine Room R/B No. 2
F10
Fusible Link BlockSuspension Control
ECU
AIR SUS No. 2
2
1
22 W
AIR SUS
9ALT
5B
Battery
IFJ12
J/C
AW±B22
S25
GND 24
S25
25
S25
BAT B J/C
B
J37
B
J37 C
J38 V
IA55
VV
V
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±763
957 Author: Date:
2005 SEQUOIA (RM1146U)
DTC C1774/74 Power Source Circuit
CIRCUIT DESCRIPTION

This circuit provides power to operate the suspension control ECU.

The suspension control ECU, controlling the air suspension system, is activated when the ignition
switch is turned ON. The main relay inside the ECU is activated after 2 seconds and the system is oper-
ated by +B power source.
DTC No.DTC Detecting ConditionTrouble Area
C1774/74The terminal B or BAT voltage is below 10 V or above 16 V for
0.5 seconds.
Battery

Power source circuit

Suspension control ECU
WIRING DIAGRAM
DIDE3±01

F16805
S25
BAT
B
Wire Harness View:
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±765
959 Author: Date:
2005 SEQUOIA (RM1146U)
A
3 Inspect fuse (AIR SUS No. 2).
PREPARATION:
Remove the AIR SUS No. 2 fuse from the engine room R/B.
CHECK:
Check continuity of the AIR SUS No. 2 fuse.
OK:
Continuity
NG Inspect for short circuit in all harness and com-
ponents connected to AIR SUS No. 2 fuse.
OK
4 Inspect suspension control ECU.
PREPARATION:
Disconnect the ECU connector.
CHECK:
Measure the voltage between terminal S25±24 (B) of the sus-
pension control ECU connector and body ground and between
terminal S25±25 (BAT) and body ground.
OK:
Voltage: 10 to 14 V
NG Repair or replace harness or connector.
OK

DI±782
± DIAGNOSTICSAIR SUSPENSION SYSTEM
976 Author: Date:
2005 SEQUOIA (RM1146U)
DTC U0100/65 Lost Communication with ECM/PCM
CIRCUIT DESCRIPTION
The ECM sends signals such as engine speed signal, transmission signal, shift position signal, L4 switch
signal, TC terminal signal (diagnosis mode signal) to the suspension control ECU, etc. when the air suspen-
sion system is in operation.
DTC No.DTC Detecting ConditionTrouble Area
U0100/65
The suspension control ECU detects the following conditions
simultaneously:
1. Ignition switch ON
2. Vehicle speed signal is more than 30 km/h (18.5 mph)
3. No communication from ECM continues for more than 3
seconds

ECM

Suspension control ECU

Communication circuit
INSPECTION PROCEDURE
HINT:
This circuit uses CAN for communication. Therefore, if there are any malfunctions in the communication cir-
cuit, one or more DTCs in the CAN communication system is/are output.
1 Go to CAN communication system (See page DI±1065).
DIDEG±01

F19450
C6
Combination
MeterSuspension Control
ECU
I18
Ignition SW Instrument Panel J/B
Engine Room J/B24
14
15
16 LO
N
HIP
B±L
GR±R26
S25
9
S25
8
S25LO
NR
HI
6
IG2 AM25
W±R B±R IGN1 11
7 1H
1J1C
1C32
W±R
AM2
1
2C
2D1
B
Battery B±O
B 5 4F10
FL Block
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±785
979 Author: Date:
2005 SEQUOIA (RM1146U)
Height Control Indicator Lamp Circuit
CIRCUIT DESCRIPTION
The height control indicator lamp indicates the target height, not the actual height.
It blinks when the height control is operated by pressing the height control switch and stays on when the
operation is completed.
WIRING DIAGRAM
DIDEL±01