DTC P0010 TOYOTA SEQUOIA 2001 Service Repair Manual

DI3HB±12
DI±58
± DIAGNOSTICSENGINE
252 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for the codes listed
in the table below. For details of each code, refer to the ºSee pageº under the respective ''DTC No.'' in the
DTC chart.
DTC No.
(See page)Detection ItemTrouble AreaMIL*1Memory
P0010
(DI±73)Camshaft Position ºAº Actuator
Circuit (Bank 1)
Open or short in OCV circuit

OCV

ECM

P0011
(DI±79)Camshaft Position ºAº ±Timing
Over± Advanced or System Per-
formance (Bank 1)
Valve timing

OCV

VVT controller assembly

ECM

P0012
(DI±79)Camshaft Position ºAº ±Timing
Over± Retarded (Bank 1)

Valve timing

OCV

VVT controller assembly

ECM

P0016
(DI±85)Crankshaft Position ± Camshaft
Position Correlation (Bank 1
Sensor A)
Open or short in VVT sensor circuit

VVT sensor

ECM

P0018
(DI±85)Crankshaft Position ± Camshaft
Position Correlation (Bank 2
Sensor A)
Open or short in VVT sensor circuit

VVT sensor

ECM

P0020
(DI±73)Camshaft Position ºAº Actuator
Circuit (Bank 2)
Open or short in OCV circuit

OCV

ECM

P0021
(DI±79)Camshaft Position ºAº ±Timing
Over± Advanced or System Per-
formance (Bank 2)
Valve timing

OCV

VVT controller assembly

ECM

P0022
(DI±79)Camshaft Position ºAº ±Timing
Over± Retarded (Bank 2)

Valve timing

OCV

VVT controller assembly

ECM

P0031
(DI±88)Oxygen (A/F) Sensor Heater
Control Circuit Low (Bank 1 Sen-
sor 1)
Open in heater circuit of A/F sensor

A/F sensor heater

A/F relay

ECM

P0032
(DI±88)Oxygen (A/F) Sensor Heater
Control Circuit High (Bank 1
Sensor 1)
Short in heater circuit of A/F sensor

A/F sensor heater

A/F relay

ECM

P0037
(DI±93)Oxygen Sensor Heater Control
Circuit Low (Bank 1 Sensor 2)

Open in heater circuit of heated oxygen sensor

Heated oxygen sensor heater

EFI relay

ECM

P0038
(DI±93)Oxygen Sensor Heater Control
Circuit High (Bank 1 Sensor 2)

Short in heater circuit of heated oxygen sensor

Heated oxygen sensor heater

EFI relay

ECM


DID82±01
A20891
Mass Air Flow Sensor Crankshaft Position Sensor
Actual Valve TimingCorrection Target Valve Timing
Feedback
Duty Control ECM
Camshaft Timing
Oil Control
Valve (OCV)
Vehicle Speed Signal Engine Coolant Temp. Sensor Throttle Position Sensor
Camshaft Position Sensor
± DIAGNOSTICSENGINE
DI±73
267 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
DTC P0010 Camshaft Position ºAº Actuator circuit
(Bank 1)
DTC P0020 Camshaft Position ºAº Actuator circuit
(Bank 2)
CIRCUIT DESCRIPTION
The Variable Valve Timing (VVT) system includes the ECM, the Oil Control Valve (OCV) and the VVT control-
ler. The ECM sends a target ºduty±cycleº control signal to the OCV. This control signal, applied to the OCV,
regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on en-
gine operation conditions such as intake air volume, throttle position and engine coolant temperature.
The ECM controls the OCV, based on the signals output from the sensors. The VVT controller regulates the
intake camshaft angle using oil pressure through the OCV. As a result, the relative position between the cam-
shaft and the crankshaft is optimized, and the engine torque improves, fuel economy improves, and exhaust
emissions decrease under overall driving conditions. Also, the ECM detects the actual valve timing using
signals from the camshaft position sensor and the crankshaft position sensor, and performs feedback con-
trol. This is how target valve timing is verified by the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P0010
P0020Open or short in OCV circuit

Open or short in OCV circuit

OCV

ECM

DI±74
± DIAGNOSTICSENGINE
268 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR DESCRIPTION
After the ECM sends the ºtargetº duty±cycle signal to the OCV (Oil Control Valve), the ECM monitors the
OCV current to establish an ºactualº duty±cycle. When the actual duty±cycle ratio varies from the target
duty±cycle, the ECM sets a DTC.
MONITOR STRATEGY
RltdDTCP0010VVT oil control valve bank 1 range checkRelated DTCsP0020VVT oil control valve bank 2 range check
Required sensors/componentsOCV
Frequency of operationContinuous
Duration1 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Battery voltage11 V13 V
Target duty ratio±70%
StarterOFF
Current cut statusNot cut
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Either of the following conditions is met:Condition 1 or 2
1. Output signal duty for OCVOutput duty ratio is 100% (always ON) but target duty ratio is less than 70%
2. Output signal duty for OCVOutput duty is 3% or less despite the ECM supplying current to the OCV
COMPONENT OPERATING RANGE
ParameterStandard Value
Output signal duty for OCVºMore than 3%º and ºless than 100%º

A07621A09776
1
2L±W
P±LOC1+
OC1±
OC2+
OC2± 17
L±B
R±L 1
2E6 C13
OCV (Bank 1)
C14
OCV (Bank 2)ECM
16
15
14 E6
E6
E6
± DIAGNOSTICSENGINE
DI±75
269 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0010 displayed, check left bank OCV circuit.

If DTC P0020 displayed, check right bank OCV circuit.

Read freeze frame data using hand±held tester. Because freeze frame records the engine conditions
when the malfunction is detected. When troubleshooting, it is useful for determining whether the ve-
hicle was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc.
at the time of the malfunction.

± DIAGNOSTICSENGINE
DI±79
273 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0011 Camshaft Position ºAº ±Timing Over±
Actuator or System Performance (Bank 1)
DTC P0012 Camshaft Position ºAº ±Timing Over±
Retarded (Bank 1)
DTC P0021 Camshaft Position ºAº ±Timing Over±
Actuator or System Performance (Bank 2)
DTC P0022 Camshaft Position ºAº ±Timing Over±
Retarded (Bank 2)
CIRCUIT DESCRIPTION
Refer to DTCs P0010 on page DI±73.
DTC No.DTC Detecting ConditionTrouble Area
P0011
P0021
Advanced cam timing:
After engine is warmed up and engine speed is at 400 to
4,000 rpm, condition (a) continues. (1 trip detection logic)
(a) Valve timing does not change from current valve timing

Valve timing

OCV
P0012
P0022
Retarded cam timing:
After engine is warmed up and engine speed is at 400 to
4,000 rpm, condition (a) continues. (2 trip detection logic)
(a) Valve timing does not change from current valve timing

OCV

VVT controller assembly

ECM
MONITOR DESCRIPTION
The ECM optimizes the valve timing using the VVT (Variable Valve Timing) system to control the intake valve
camshaft. The VVT system includes the ECM, the OCV (Oil Control Valve) and the VVT controller. The ECM
sends a target ºduty±cycleº control signal to the OCV. This control signal, applied to the OCV, regulates the
oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake valve cam-
shaft.
Example:
A DTC will set if: 1) the difference between the target and actual valve timing is more than 5 degrees of the
crankshaft angle (CA) and the condition continues for more than 4.5 sec.; or 2) the OCV is forcibly activated
63 times or more.
Advanced cam DTCs are subject to º1 tripº detection logic.
Retarded cam DTCs are subject to º2 tripº detection logic.
DIAON±02

DI±80
± DIAGNOSTICSENGINE
274 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P0011VVT system advance (Bank 1)
RltdDTCP0012VVT system retard (Bank 1)Related DTCsP0021VVT system advance (Bank 2)
P0022VVT system retard (Bank 2)
Main sensors/componentsCamshaft position sensor
Required sensors/componentsRelated sensors/componentsEngine coolant temperature sensor,
Crankshaft position sensor
Frequency of operationOnce per drive cycle
Duration10 sec.
MIL operationP0011, P0021: Immediate
P0012, P0022: 2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
Battery voltage11 V±
Throttle position learningCompleted
Engine RPM400 rpm4,000 rpm
Engine coolant temperature75C (167F)100C (212F)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Deviation of valve timingMore than 5CA
OCV activation63 times or more
Response of valve timing1 sec./1CA or more
WIRING DIAGRAM
Refer to DTCs P0010 on page DI±73.
INSPECTION PROCEDURE
HINT:

Bank 1 refers to bank that includes cylinder No. 1.

Bank 2 refers to bank that does not include cylinder No. 1.

If DTC P0011, P0012 is displayed, check the bank 1 VVT system.

If DTC P0021, P0022 is displayed, check the bank 2 VVT system.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. at
the time of the malfunction.

DI±84
± DIAGNOSTICSENGINE
278 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check whether or not DTC P0010, P0012, P0021 or P0022 is stored.
PREPARATION:
(a) Clear the DTC (See page DI±43).
(b) Perform simulation test.
CHECK:
Check whether or not DTC P0011, P0012, P0021 or P0022 is stored (See page DI±43).
OK:
Standard: DTC P0011, P0012, P0021 or P0022 is not stored.
OK VVT system is OK.*
*: DTC P0011, P0012, P0021 or P0022 is also output when a
foreign object is detected in some parts of the system in the en-
gine oil, and then the system returns to normal in a short time.
As ECM is controlled to eject a foreign object, there is no prob-
lem on the VVT. There is also no problem on the VVT as the oil
filter should catch the foreign object in the engine oil.
NG
Replace ECM.