diagram TOYOTA SEQUOIA 2001 Service Repair Manual

V08423 Knock Sensor 1
GRECM
KNK
E1 12
E6
WIRING DIAGRAM
Wiring Diagram
This shows a wiring diagram of the circuit.
Use this diagram together with ELECTRICAL
WIRING DIAGRAM to thoroughly understand the
circuit.
Wire colors are indicated by an alphabetical code.
B = Black, L = Blue, R = Red, BR = Brown,
LG = Light Green, V = Violet, G = Green,
O = Orange, W = White, GR = Gray, P = Pink,
Y = Yellow, SB = Sky Blue
The first letter indicates the basic wire color and
the second letter indicates the color of the stripe.
DTC P0325Knock Sensor 1 Circuit Malfunction
CIRCUIT DESCRIPTION
Knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelectric element which
generates a voltage when it becomes deformed, which occurs when the cylinder block vibrates due to knocking. If engine
knocking occurs, ignition timing is retarded to suppress it.
DTC No. DTC Detecting Condition Trouble Area
P0325No knock sensor 1 signal to ECM with engine speed,
1,200 rpm or more. Open or short in knock sensor1 circuit
 Knock sensor 1 (looseness)
 ECM
If the ECM detects the above diagnosis conditions, it operates the fall safe function in which the corrective retard angle
value is set to the maximum value.
 Diagnostic Trouble Code No. and Detection Item
 Circuit Description
The major role and operation, etc. of the circuit
and its component parts are explained.
 Indicates the diagnostic trouble code, diagnostic
trouble code set parameter and suspect area of
the problem.

± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN±33
33 Author: Date:
2005 SEQUOIA (RM1146U)
6. CIRCUIT INSPECTION
How to read and use each page is shown below.

DID7Q±01
B17429
ECM
IG SW
IGSW
STSW
STAR/NSW
STA
BATT
MREL
+BM
+B
+B2
VCPA
VPA
EPA
VCP2
VPA2
EPA2W
OC1+
OC1±
OC2+
OC2±
KNK1
EKNK
KNK2
EKN2
G2+
G2±
NE+
NE±
VV1+
VV1±
VV2+
VV2± ETCSMIL
To Battery
To Battery
To Battery
To BatteryTo Starter ST Relay
PNP SW
EFI No.1
EFI No.1 Relay
Acclererator Pedal
Position SensorCombination Meter
VVT OCV
(Bank 1)
VVT OCV
(Bank 2)
Knock Sensor
(Bank 1)
Knock Sensor
(Bank 2)
Camshaft Position
SensorTo V C
Terminal
Crankshaft
Position Sensor
VVT Sensor
(Bank 1)
VVT Sensor
(Bank 2) DI±6
± DIAGNOSTICSENGINE
200 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

A07621A09776
1
2L±W
P±LOC1+
OC1±
OC2+
OC2± 17
L±B
R±L 1
2E6 C13
OCV (Bank 1)
C14
OCV (Bank 2)ECM
16
15
14 E6
E6
E6
± DIAGNOSTICSENGINE
DI±75
269 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0010 displayed, check left bank OCV circuit.

If DTC P0020 displayed, check right bank OCV circuit.

Read freeze frame data using hand±held tester. Because freeze frame records the engine conditions
when the malfunction is detected. When troubleshooting, it is useful for determining whether the ve-
hicle was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc.
at the time of the malfunction.

DI±80
± DIAGNOSTICSENGINE
274 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P0011VVT system advance (Bank 1)
RltdDTCP0012VVT system retard (Bank 1)Related DTCsP0021VVT system advance (Bank 2)
P0022VVT system retard (Bank 2)
Main sensors/componentsCamshaft position sensor
Required sensors/componentsRelated sensors/componentsEngine coolant temperature sensor,
Crankshaft position sensor
Frequency of operationOnce per drive cycle
Duration10 sec.
MIL operationP0011, P0021: Immediate
P0012, P0022: 2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
Battery voltage11 V±
Throttle position learningCompleted
Engine RPM400 rpm4,000 rpm
Engine coolant temperature75C (167F)100C (212F)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Deviation of valve timingMore than 5CA
OCV activation63 times or more
Response of valve timing1 sec./1CA or more
WIRING DIAGRAM
Refer to DTCs P0010 on page DI±73.
INSPECTION PROCEDURE
HINT:

Bank 1 refers to bank that includes cylinder No. 1.

Bank 2 refers to bank that does not include cylinder No. 1.

If DTC P0011, P0012 is displayed, check the bank 1 VVT system.

If DTC P0021, P0022 is displayed, check the bank 2 VVT system.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. at
the time of the malfunction.

A02961
V5
VVT Sensor (Bank 1)ECM
1
2R
G
Y
LVVL+
VVL±
VVR+
E5 18
19
19
18
VVR±
1
2E5
E4
E4 V6
VVT Sensor (Bank 2)
± DIAGNOSTICSENGINE
DI±87
281 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTC P0016 is displayed, check left bank VVT sensor.

If DTC P0018 is displayed, check right bank VVT sensor.

Read freeze frame data using hand±held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for deter-
mining whether the vehicle was running or stopped, the engine was warmed up or not, the air±fuel ratio
was lean or rich, etc. at the time of the malfunction.
1 Check valve timing (Check for loose and jumping teeth of timing belt) (See page
EM±16).
NG Adjust valve timing (Repair or replace timing
belt).
OK
Replace ECM (See page SF±80).

B17396
HT +B
AF± AF+ Sensor 1A/F Sensor Component Side:
Front View
DI±90
± DIAGNOSTICSENGINE
284 Author: Date:
2005 SEQUOIA (RM1146U) P0032, P0052 (High current):
Time after engine start10 sec.±
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
P0031, P0051 (Low current):
A/F sensor heater currentLess than 0.8 A
P0032, P0052 (High current):
A/F sensor heater currentMore than 10 A
COMPONENT OPERATING RANGE
ParameterStandard Value
A/F sensor heater current1.8 to 3.4 A at 20°C (68°F)
WIRING DIAGRAM
Refer to DTC P2195 on page DI±383.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using a hand±held tester or OBD II scan tool. Freeze frame data record the engine
condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if
the vehicle was moving or stationary, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, and other data, from the time the malfunction occurred.
1 Check resistance of air±fuel ratio (A/F) sensor heater.
PREPARATION:
Disconnect the air±fuel ratio (A/F) sensor connector.
CHECK:
Measure resistance between the terminals of the A/F sensor
connector.
OK:
Standard:
Tester ConnectionSpecified Condition
HT (1) ± +B (2)1.8 W to 3.4 W at 20C (68F)
HT (1) ± AF± (4)10 kW or higher
NG Replace air±fuel ratio (A/F) sensor.
OK

A23550
Battery 2FECM
OX1B HT2B
OX2B 33 Y
AG±R 3 2
ERB±W
EDW±B
5
4
5 1
22J2
IG4
HTR2
NTL2 OXR2
E8
F10
Fusible Link
Block G±R
EC 2D112H6
2A2 EFI Relay
EFI No. 1
EFI No. 2
J/C
IA4
G±R
HT1B 8
5
18
E8 E7
E7 E4
G±R G±R14
IA4 B±W
OXL21 4
A G±R Engine Room J/B
J42
J/CA
B J5
J/CW±R
E8
E6 G±W
BR
BR
H4 Heated Oxygen Sensor
(Bank 2 Sensor 2)
H2 Heated Oxygen Sensor
(Bank 1 Sensor 2)
J16
28
1 (Shielded) B
E B
EB J42
J/C G±W G±W
E1B
GJ/C
E1 +B
+B
E1 E2 MREL
(Shielded)
CC
C
BR DI±98
± DIAGNOSTICSENGINE
292 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

F10
Fusible
Link
Block
A23554
ECM
VG
E2G 8
E4
30
E8
29
E8 B±W R±W
2
B IA414
BatteryB 2F1 2D1 Engine Room J/B
EFI No. 1 EFI Relay
EFI No. 2
5
3
1
2 2H2A2G±R J2
J/C
A
B G±R
IG422
G±R
3 IA44B±W
J16
J/C
6B
W±B G±RA
A
J5
J/C
ED
+B
VG
MREL
M1
Mass Air Flow Meter
B±W
G±R
1
4
5 E2G DI±104
± DIAGNOSTICSENGINE
298 Author: Date:
2005 SEQUOIA (RM1146U)
COMPONENT OPERATING RANGE
ParameterStandard Value
Mass air flow meter voltage0.4 to 2.2 V
WIRING DIAGRAM

A15651
ECM
Intake Air Temp. Sensor
(Built into Mass Air Flow Meter)
54 Y±G5 V
THA 22R
E8
E8 G±W28
E2
E1 M1
THA
E2
± DIAGNOSTICSENGINE
DI±115
309 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs related to different systems that have terminal E2 as the ground terminal are output simulta-
neously, terminal E2 may have an open circuit.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.

FI6448
ECM
5 V
THW E2
Engine Coolant Temp. Sensor
2
1G±Y
G±W
E1 E2
E8
E8
2821
± DIAGNOSTICSENGINE
DI±121
315 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

If DTCs related to different system that have terminal E2 as the ground terminal are output simulta-
neously, terminal E2 may have an open circuit.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.