high beam TOYOTA SEQUOIA 2001 Service Repair Manual

DID8Q±01
DI±1608
± DIAGNOSTICSCOMBINATION METER SYSTEM
1802 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. METER GAUGE AND WARNING/INDICATOR
GAUGE:
ItemDetail
SpeedometerVehicle speed sensor (Direct line).
TachometerECM transmits engine speed to the meter to display.
ODO/TRIP MeterCombination meter assy.
FuelDisplays a fuel level according to a signal from the fuel sender gauge (Direct line).
Water TemperatureDisplays engine coolant temperature according to a signal from the ECM (BEAN).
Oil PressureReceives a signal from the oil pressure sender (Direct line).
Volt MeterDisplays vehicle voltage according to a voltage from the IG terminal (Direct line).
WARNING/INDICATOR:
HINT:
Combination meter bulb check is performed for 3 seconds after the ignition switch is turned ON.
ItemDetailList of indicators available for
bulb check
O/D OFFReceives a signal from the ECM (Direct line)±
TURNTurns signal switch ON (Direct line)±
BEAMReceives a signal from the body ECU (*1), Displays a signal received from the
dimmer switch (*2) (Direct line)±
SECURITYReceives a set signal from the transponder key ECU and body ECU (Direct line)±
CHARGEReceives a malfunction signal from the alternator (Direct line)
AIR BAGReceives a malfunction signal from the airbag sensor center (Direct line)
D SEAT BELTReceives the driver seat belt signal (Unfastened) from the seat belt inner front LH
(Direct line)±
DOOROpen door indicator comes on when a signal is received from the ECU (BEAN)
from each door±
A/T OIL TEMP.Warning is displayed when the oil temperature is high (Direct line)
BRAKEComes on when the parking brake switch is on or the brake fluid level warning
switch is on (Direct line)
MIL (CHECK ENGINE)Receives a malfunction signal from the ECM (Direct line)
FUEL WARNINGReceives the fuel empty signal from the fuel sender gauge (Direct line)±
ABSReceives a malfunction signal from the skid control ECU (Direct line)
WASHERWarning is displayed when the washer level is low (Direct line)±
CRUISEReceives a CRUISE on signal or malfunction signal from the ECM (Direct line)±
VSC TRACReceives a malfunction signal from the skid control ECU (Direct line)
VSC (TRAC) OFFReceives a malfunction signal from the translate ECU (Direct line)
SLIPReceives a malfunction signal from the translate ECU (Direct line)
4HIReceives a 4HI signal from the 4WD control ECU (Direct line)±
CTR DIF LOCKReceives a DIF LOCK signal from the 4WD control ECU (Direct line)±
A/T PReceives a P signal from the park/neutral position switch (Direct line)±
A/T NReceives an N signal from the park/neutral position switch (Direct line)±
A/T DReceives a D signal from the park/neutral position switch (Direct line)±
A/T 3Receives a 3 signal from the park/neutral position switch (Direct line)±
A/T 2Receives a 2 signal from the park/neutral position switch (Direct line)±
A/T LReceives an L signal from the park/neutral position switch (Direct line)±

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1615
1809 Author: Date:
2005 SEQUOIA (RM1146U) Seat belt warning lamp for driver's seat does not operate.
Refer to troubleshooting proceduresDI±1650
SLIP warning light does not come on.
1. SLIP warning light circuit
2. Wire harness and connector
3. Combination meter assy
4. Skid control ECUDI±1041
±
IN±35
IN±35
INDICATOR LIGHTS:
SymptomSuspected AreaSee page
Turn indicator light does not come on.
1. Turn signal flasher relay
2. Wire harness or connector
3. Combination meter assyBE±36
±
IN±35
High beam indicator light does not come on.
1. Headlight dimmer switch (*1)
Headlight dimmer switch circuit (*2)
2. Wire harness or connector
3. Combination meter assyBE±27
DI±1755
±
IN±35
Washer level indicator light does not come on.
1. Washer level warning switch
2. Wire harness or connector
3. Combination meter assyBE±49
±
IN±35
Tire pressure indicator light does not come on.
1. Tire pressure monitor ECU
2. Wire harness or connector
3. Combination meter assyDI±873
±
IN±35
CRUISE main indicator light does not come on.
1. CRUISE main indicator light circuit
2. Cruise main control switch circuit
3. Wire harness or connector
4. Combination meter assyDI±1557
DI±1561
±
IN±35
VSC OFF indicator light does not come on.1. VSC OFF indicator light circuit
2. Combination meter assyDI±1048
IN±35
VSC TRAC indicator light does not come on.1. VSC TRAC indicator light circuit
2. Combination meter assyDI±1027
IN±35
Security indicator light does not come on.1. Security indicator light circuit
2. Combination meter assyDI±1731
IN±35
4HI indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
4LO indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
CTR DIF LOCK indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
Height control indicator lamp does not come on.1. Height control indicator lamp circuit
2. Combination meter assyDI±785
IN±35
Height control manual indicator lamp does not come on.1. Height control manual indicator lamp circuit
2. Combination meter assyDI±789
IN±35
A/T indicator light does not come on.
1. Park/neutral position switch circuit
2. Wire harness and connector
3. Combination meter assyDI±576
±
IN±35
*1: w/o Day time running light
*2: w/ Day time running light
OTHERS:
SymptomSuspected AreaSee page
All buzzers (key reminder, seat belt) do not operate.Combination meter assyIN±35

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1627
1821 Author: Date:
2005 SEQUOIA (RM1146U)
ACTIVE TEST
Performing the ACTIVE TEST using the hand±held tester allows the meters, indicators and so on to operate
without part removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten
labor time.
It is possible to display the DATA LIST on the hand±held tester during the ACTIVE TEST.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
SPEED METER
Operate speedometer: 0 / 40 (24) / 80 (48) / 120
(72) / 160 (96) /
200 (120) km/h (mph)The needle position should be within the accept-
able tolerance
TACHOMETER
Operate tachometer:
0 rpm / 1,000 rpm / 2,000 rpm / 3,000 rpm /
4,000 rpm / 5,000 rpm / 6,000 rpm / 7,000 rpmConfirm that the vehicle is stopped and engine is
idling.
FUEL GAUGEOperate fuel gauge: EMPTY, 1/2, FULLConfirm that the vehicle is stopped and engine is
idling.
COOLANT TEMPOperate engine coolant temperature receiver
gauge: HIGH / NORMAL / LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
D BELT REMINDOperate driver's seat belt warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
OPEN DOOR WARNOperate open door warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
LOW FUEL WARNOperate fuel level warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
TAILLIGHT INDICOperate taillight indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
HEADLIGHT INDICOperate Hi±beam indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
SRS WARNOperate SRS warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
ODO/TRIP DISPOperate ODO/TRIP display: OFF / ONConfirm that the vehicle is stopped and engine is
idling.
KEY REMND BUZZROperate key reminder buzzer: OFF / ONConfirm that the vehicle is stopped and engine is
idling.
SEAT BELT BUZZROperate driver's seat belt warning buzzer:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
MAINT REQDOperate oil maintenance indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
VOLT METEROperate volt meter: 9 V / 12 V / 15 V / 18VConfirm that the vehicle is stopped and engine is
idling.
OIL PRESS METEROperate oil pressure meter: HIGH, 3/4, 1/2, 1/4,
LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.

I28521
1B
1B1
2
7
1B 1F9Y±R
B6
B6 11
8
R±L Instrument Panel J/B
Y±R
W±BHF HU
J8
J/C A
IE16 LOW
HIGH
FLASH Headlight
Dimmer
Switch
W±BC8 Combination Switch
EL HF HU87Body ECU w/ Daytime Running Light:
± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1755
1949 Author: Date:
2005 SEQUOIA (RM1146U)
Headlight dimmer switch circuit
CIRCUIT DESCRIPTION
This circuit detects the headlight dimmer switch condition.
w/ daytime running light:
The body ECU detects the headlight dimmer switch position and turns on the DIMMER relay.
The body ECU informs the combination meter of the headlight dimmer switch condition via BEAN.
When the headlight dimmer switch position is HI or FLASH, the HI beam indicator light on the combination
meter comes on.
w/o daytime running light:
When the headlight dimmer switch position is HI or FLASH, the HI beam indicator light on the combination
meter comes on.
When the HI beam headlights come on, current is supplied to the HI beam indicator light on the combination
meter to turn the indicator light on.
WIRING DIAGRAM
DI94U±08

I28522
Body ECU
R±L
B6
HF
B6 Instrument Panel J/B
Combination MeterHU 1B
1BY±R
1F
1B21
79
6
1D
AJ8
J/C118
B
R±GIE Headlight
Dimmer
SwitchLOW
HIGH
FLASHHL
HU HF EL 17
87
BR W±B Y±R
C6C6 1712W±B

HIGH Beam Indicator R±G
C8 Combination Switch
16 w/o Daytime Running Light:
R±G
B BB R±G
R±G 11
2
IA5 IA1
R±G
To Head Light RH
To Head Light LH J4
J/C DI±1756
± DIAGNOSTICSBODY CONTROL SYSTEM
1950 Author: Date:
2005 SEQUOIA (RM1146U)

CH±4
± CHARGINGCHARGING SYSTEM
2896 Author: Date:
2005 SEQUOIA (RM1146U)
If the voltmeter reading is more than the standard voltage, re-
place the voltage regulator.
If the voltmeter reading is less than the standard voltage, check
the voltage regulator and generator.
10. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and set the heater blower switch to HI.
(b) Check the reading on the ammeter.
Standard amperage: 30 A or more
If the ammeter reading is less than the standard amperage, re-
pair the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.
11. REINSTALL ENGINE UNDER COVER

I12794
13 16 15 14 9 8
17 HIAUTO
LO
OFF
FlashTAIL
3
21 54 6
7
10 12 11
BE2MT±01
I18635
1
2 34
5
I0502712
3 5
1
2 3
5
I18635
1
2 34
5
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE±27
3431 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF±No continuity
TAIL14 ± 16Continuity
HEAD13 ± 14 ± 16Continuity
AUTO12 ± 16Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
Flash7 ± 8 ± 16Continuity
Low beam16 ± 17Continuity
High beam7 ± 16Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEAD RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 ± 2Continuity
Constant3 ± 5No continuity
Apply B+ between
terminals 1 and 2.3 ± 5Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 ± 2Continuity
Constant3 ± 5No continuity
Apply B+ between
terminals 1 and 2.3 ± 5Continuity
If continuity is not as specified, replace the relay.
5. INSPECT DRL NO. 4 RELAY CONTINUITY (w/ Daytime
Running Light)
ConditionTester connectionSpecified condition
Constant1 ± 2Continuity
Constant3 ± 5No continuity
Apply B+ between
terminals 1 and 2.3 ± 5Continuity
If continuity is not as specified, replace the relay.

I18654
0.4 °
3 m (9.84 ft) H 20.9 mm
(0.823 in.)
7
V RH Line
90 °
V LH Line4V LH LineV Line V RH Line 65
6
V LH LineV Line
V RH Line 6
5
6
H4
O: step No.H4
20.9 mm
(0.823 in.) 1,348 mm (53.1 in.) Low Beam:
High Beam:29.7 mm
(1.17 in.)
20.9 mm
(0.823 in.)
1,348 mm (53.1 in.)
1,348 mm
(53.1 in.) High Beam
Low BeamH RH and
H LH
7
BE±32
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
3436 Author: Date:
2005 SEQUOIA (RM1146U)
2. ADJUST HEADLIGHT AIM ONLY
(a) Place the vehicle in the following conditions.

The area around the headlight is not deformed.

The vehicle is parked on a level surface.

Tire inflation pressure is the specified value.

A driver is in the driver's seat and the vehicle is in a state ready for driving (with a tank full).

The vehicle has been bounced several times.
(b) Check the headlight aiming.
(1) Prepare a thick white paper.
(2) Stand the paper perpendicular to the ground at the position 3 m (9.84 ft) away from the headlights
bulb center.
(3) Ensure that the center line of the vehicle and the paper face forms a 90±degree angle as shown
in the illustration.
(4) Draw a horizontal line (H line) on the paper, showing where the headlights should strike.
(5) Draw a vertical line (V line) at the position where the extended center line of the vehicle strikes.
(6) Draw 2 vertical lines (by connecting the low and high beam center marks) to where the both head-
lights should strike (V RH and V LH lines).
(7) Draw a horizontal line (by connecting the both low beam center marks) at the position where the
headlights should strike (H RH and H LH lines).
HINT:
The H RH and H LH line is 0.4° below the horizontal line (H line) of the light axis.
(8) Start the engine.
(9) Turn the headlights ON.
(10) Check that the headlights properly strike the position shown in the illustration.
(11) If not, adjust the lights in the vertical or horizontal direction.
HINT:
As shown in the illustration, adjust each aim of the RH and LH lights.
(c) When adjusting it in the vertical direction:
Using adjusting bolt, adjust the headlight aim to within the specified range.

05_SEQUOIA_U (L/O 0408)
11
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Automatic transmission indicator lights
Traction control system off indicator light
(two±wheel drive models)
Vehicle stability control system off indicator light
(four±wheel drive models) Slip indicator light
Headlight high beam indicator lightOverdrive±off indicator light
Turn signal indicator lights
Engine immobilizer/theft deterrent system
indicator light
Front passenger occupant classification
indicator light
Roll sensing of curtain shield airbags off
indicator light
Headlight low beam indicator light
Tail light indicator lightLow speed four±wheel drive indicator light*
2
High speed four±wheel drive indicator light*
2
Center differential lock indicator light*
2
(four±wheel drive models)

05_SEQUOIA_U (L/O 0408)
145
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
The lights automatically turn off after 30
seconds when all the side doors and back
door are closed with the ignition key in
the ªACCº or ªLOCKº position and the le-
ver at position 2.
The lights also automatically turn off when
the driver 's door is opened with the lever
at position 1.
If the doors are locked by the wireless
remote control transmitter, the lights auto-
matically turn off immediately.
To turn them on again, turn the key to the
ªONº position or actuate the headlight
switch.
If you are going to park for over one
week, make sure the headlight switch is
off.
The time before the headlights turn off
can be changed. For details, contact your
Toyota dealer.
NOTICE
To prevent the battery from being dis-
charged, do not leave the lights on
for a long period when the engine is
not running.
Daytime running light system (all mod-
els sold in Canada and some models
sold in the U.S.A.)
The headlights turn on when the parking
brake is released with the engine started,
even with the light switch in the ªOFFº
position. They will not go off until the
ignition switch is turned off.
To turn on the other exterior lights and
instrument panel lights, twist the knob to
position 1.
Under the daytime running light system,
the headlights turn on at reduced intensity.
Twist the knob to position 2 to turn to full
intensity for driving at night.
High±Low beamsÐFor high beams, turn
the headlights on and push the lever away
from you (position 1). Pull the lever to-
ward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will
tell you that the high beams are on.
Flashing the high beam headlights
(position 3)ÐPull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights
with the knob turned to ªOFFº.