spare tire TOYOTA SEQUOIA 2001 Service Repair Manual

DIDJT±01
F19148
Combination Meter
Tire Pressure
Warning Lamp DI±796
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
990 Author: Date:
2005 SEQUOIA (RM1146U)
TIRE PRESSURE WARNING SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77
1. TIRE PRESSURE WARNING SYSTEM PRECAUTION
(a) When the tire pressure warning lamp comes on, immedi-
ately check the tire pressure of the tire and adjust it to the
specified pressure. (The tire pressure warning lamp
comes on if there is an open in the tire pressure warning
lamp circuit.)
NOTICE:
Check the spare tire as well since this system monitors
pressure of all tires, including the spare.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) When the tire pressure warning lamp blinks, there is a
malfunction in the system. Check for DTCs.
(c) It is necessary to register the transmitter ID in the tire pres-
sure monitor ECU when replacing the tire pressure moni-
tor valve sub±assy and/or tire pressure monitor ECU (see
page DI±805).
(d) When replacing the tire pressure monitor ECU.
(1) Using the DATA LIST, read the transmitter IDs regis-
tered in the ECU and make a note of them before
removing the tire pressure monitor ECU.
(2) Register the transmitter IDs after installing a new
tire pressure monitor ECU.
(e) When replacing the tire pressure monitor valve sub±assy.
(1) Make a note of the 7 digit number (transmitter ID)
written on the tire pressure monitor valve sub±assy
when replacing the tire pressure monitor valve sub±
assy. Register the transmitter IDs in the tire pres-
sure monitor ECU after replacing the tire pressure
monitor valve sub±assy and installing the tires and
wheels on the vehicle.

DIDJV±01
F19126
Combination meter assy
(Vehicle speed signal)
Tire pressure monitor receiver assyCombination meter assy
(Tire pressure warning lamp) Tire
Pressure
Monitor
ECU
: Radio signal
Tire Pressure Sensor
(Tire pressure monitor valve
sub±assy) (FR LH)
Tire Pressure Sensor
(Tire pressure monitor valve
sub±assy) (FR RH)
Tire Pressure Sensor
(Tire pressure monitor valve
sub±assy) (RR LH)
Tire Pressure Sensor
(Tire pressure monitor valve
sub±assy) (RR RH)
Tire Pressure Sensor
(Tire pressure monitor valve
sub±assy) (SPARE)
DLC3
Tire pressure warning reset switch
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±799
993 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±801
995 Author: Date:
2005 SEQUOIA (RM1146U)

When the spare tire is not within the receivable range of the electric wave, a signal may not be
received because spare tires are fixed. Accordingly, the system may not function properly. If
there is a possibility that the TPWS system does not receive a signal from the spare tire, rotate
the tire 90°.
HINT:

If any other wheels than the specified ones are used, the system may not function properly because
the radio waves are differently transmitted from the tire pressure sensor.

Depending on the tire type, the system may not function properly even though the specified wheels
are used.
(c) The average use life of the grommet of the tire pressure monitor valve sub±assy is approximately 5
years, at which time it must be replaced.
(d) After removing and installing the ECU or a sensor, output a diagnosis code and check that it is a normal
code.
3. FUNCTION OF COMPONENTS
ComponentsFunction
Tire pressure monitor valve sub±assy
Combined as a single unit with a disc wheel air valve, it measures tire pressure and
temperature and transmits an ID number for measurement value and identification.
Built±in the battery.
Tire pressure monitor receiver assyReceives and transmits a necessary signal from the transmitter to the tire pressure
monitor ECU.
Tire pressure monitor ECU
Receives the signal from the receiver and identifies it as vehicle's own signal. If the
measurement value is equal to or lower than the specified value, it transmits a sig-
nal so that the air pressure warning lamp on the combination meter comes on.
Tire pressure warning lampLocated in the combination meter, it informs the driver of lowered tire air pressure
and system failure.
Tire pressure warning reset switchEnters the initialization mode for tire or wheel replacement, or tire rotation
4. TIRE PRESSURE WARNING RESET SWITCH

By operating the tire pressure warning reset switch, the tire pressure monitor ECU can be set to issue
a warning at an inflation pressure that corresponds to the type of tires. Therefore, the dealer must set
the warning threshold to the proper value in order to comply with the local regulations.

Operate the tire pressure warning reset switch only after the inflation pressures of all 5 tires (including
the spare) have been adjusted on the vehicle.

To initialize the system, press and hold the tire pressure warning reset switch for 3 seconds or longer
with the ignition switch ON. After the system has been initialized, the warning lamp blinks 3 times (1
second ON, 1 second OFF).

During initialization, the tire pressure monitor valve sub±assy measures the inflation pressure of the
tires, and registers the signals that are transmitted into the tire pressure monitor ECU at a frequency
of one per minute. The initialization process is completed when the signals from the 5 tires have been
received.

The initialization process is canceled if the ignition switch is turned OFF during initialization. To initialize
again, the tire pressure warning reset switch must be pressed again. For this reason, once the tire pres-
sure warning reset switch has been pressed, turning OFF the ignition switch is not recommended for
a minimum of 20 minutes.

DIDJZ±01
F19326
F19327
F19328
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±805
999 Author: Date:
2005 SEQUOIA (RM1146U)
REGISTRATION
1. IN CASE OF TIRE PRESSURE MONITOR ECU REPLACEMENT
(a) Read ID stored in the old ECU using the hand±held tester.
2. IN CASE OF TIRE PRESSURE MONITOR VALVE SUB±ASSY AND/OR TIRE PRESSURE MON-
ITOR ECU REPLACEMENT
(a) Read ID written on the tire pressure monitor valve.
3. REGISTER TRANSMITTER ID
NOTICE:
It is necessary to register the transmitter ID in the tire pressure monitor ECU when replacing the tire
pressure monitor valve sub±assy and/or tire pressure monitor ECU.
(a) Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) Connect the hand±held tester to DLC3.
(c) Turn the ignition switch to the ON position.
(d) Read and write down the ID (ID1 to ID5) by using the
DATA LIST.
(e) Select the REGIST TIRE following the hand±held tester
screen.
(UTILITY ± REGIST TIRE)
(f) Input the ID (ID1 to ID5) using the hand±held tester and
transmit it to the tire pressure monitor ECU.
(g) Set the ID transmission condition to ºSUCCEEDEDº.
HINT:
If the operations of steps (d) to (f) do not complete within 5 min.,
the mode will return to normal operation mode.

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±807
1001 Author: Date:
2005 SEQUOIA (RM1146U)
4. CONFIRMATION OF TRANSMITTER ID REGISTRATION
(a) Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) Connect the hand±held tester to DLC3.
(c) Turn the ignition switch to the ON position.
(d) Select ºSIGNAL CHECKº mode on the hand±held tester (see page DI±810).
(e) Forcibly transmit the transmitter IDs for all wheels.
(1) When rapidly reducing the pressure, remove the valve core (above 20 kPa/15 sec.).
HINT:

The transmitter ID can be transmitted by rapidly reducing the tire air pressure.

When rapidly reducing the pressure, remove the valve core (above 20 kPa/15 secs.).
(2) Perform the steps mentioned above to all tires including the spare tire.
(f) Check that test mode DTCs C2181/81, C2182/82, C2183/83, C2184/84 and C2185/85 are all erased.
HINT:

The transmitter ID registration is complete when the test mode DTCs are erased.

If they haven't been erased, reset the tire pressure to the specified value and rotate the tire 90 to 270
degrees. Then forcibly transmit the transmitter IDs of all wheels. If they are still output, register the
transmitter IDs.
(g) Set the tire pressure of all wheels to the specified value.

DIDK0±01
F19150
Tire Pressure
Warning
Reset Switch
F19143
Tire Pressure Warning Lamp
ON
OFF1 sec.
1 sec. DI±808
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1002 Author: Date:
2005 SEQUOIA (RM1146U)
INITIALIZATION
1. INITIALIZATION
NOTICE:
Initialization is necessary after replacing either the ECU,
tires with different tire pressure or tire pressure monitor
valve sub±assy, after rotating the tires, or when a new ve-
hicle is delivered.
(a) Set the tire air pressure for all wheels, including the spare,
to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
(b) Keep the tire pressure warning reset switch pressed for
3 seconds or more with the ignition switch on.
(c) Check that the tire pressure warning lamp blinks 3 times
(1 second ON, 1 second OFF).
HINT:

Do not turn the ignition switch off during initialization (The
initialization process takes about 20 minutes).

Initialization will be complete if signals are received from
all the wheels including the spare. Initialization will be
canceled if the ignition switch is turned off during initializa-
tion.

DI±828
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1022 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
NOTICE:
It is necessary to register an ID code after replacing the tire pressure monitor valve sub±assy and/or
the tire pressure monitor ECU (see page DI±805).
HINT:
Set the tire pressure to the specified value.
1 Forcibly transmit transmitter ID of all wheels.
PREPARATION:
Remove the valve cores of the all wheels to rapidly reduce the pressure of all tires to 120 kPa (1.2 kgf/cm2,
17 psi respectively).
HINT:
The transmitter ID can be transmitted forcibly by rapidly reducing tire air pressure.
NEXT
2 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
OK Set tire pressure to normal value (Transmitter
stop condition is completely reset).
NG
3 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure back to the specified normal value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±829
1023 Author: Date:
2005 SEQUOIA (RM1146U)
4 Forcibly transmit transmitter ID.
PREPARATION:
(a) Forcibly transmit the transmitter ID by performing the following:
(1) Set the tire pressure to the specified value.
(2) Rotate the tire 90 to 270 degrees.
(3) Rapidly reduce the pressure of all tires to 120 kPa (1.2 kgf/cm
2, 17 psi respectively).
(4) Perform the steps mentioned above to all tires including the spare tire.
NEXT
5 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
HINT:
A system error is probable if NG. If any DTC other than C2111/21, C2112/22, C2113/23, C2114/24 and
C2115/25, is output, perform troubleshooting according to that DTC.
OK Set tire pressure to normal value (Transmitter
stop condition is completely reset).
NG
6 Check DTC (See page DI±820).
CHECK:
Check if DTCs C2111/21, C2112/22, C2113/23, C2114/24 and C2115/25 are all output.
No Go to step 12.
Ye s

F19140
Example:
Front
A
B
DI±832
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1026 Author: Date:
2005 SEQUOIA (RM1146U)
12 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
13 Identify transmitter corresponding to DTC (See page DI±881).
NEXT
14 Interchange tires.
PREPARATION:
Interchange tire ºAº with a defective tire pressure monitor valve
sub±assy with tire ºBº with a normal one.
HINT:
If tire ºAº (left front) is identified in step 13.
NEXT
15 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT

F19171
Tire Pressure
Monitor ECU Tire Pressure Monitor
Valve Sub±assy Front LH
Tire Pressure Monitor
Valve Sub±assy Rear LH Tire Pressure Monitor
Valve Sub±assy Front RH
Tire Pressure Monitor
Valve Sub±assy Rear RHJ29A
H
J30 3
4
5 BD2
5
1
4 +5V
RDA
GNDL
V
BR±R T19
Tire Pressure
Monitor Receiver
BD2
BD2L
VL
RF5V
RDA
GND2
Tire Pressure Monitor
Valve Sub±assy SpareJ29C J29B
I
J30
J
J30 BR±RBR±R J/C
T178
T177
T1716 V
: Radio Signal
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±835
1029 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT DESCRIPTION
The tire pressure monitor valve sub±assy constantly sends radio waves to the tire pressure monitor receiver
assy. If the battery for the tire pressure monitor valve sub±assy is depleted, or if the tire pressure monitor
receiver assy is defective or comes off, the DTC will be output. DTCs C2121/21 to C2125/25 can only be
deleted by the tester. DTCs C2181/81 to C2185/85 can be deleted when the transmitter sends a force trans-
mission signal or the test mode ends. DTCs C2181/81 to C2185/85 are output only in the test mode.
DTC No.DTC Detecting ConditionTrouble Area
C2121/21
C2122/22
C2123/23
C2124/24
C2125/25A DTC is detected when the ECU receives no signals for
51 minutes or more, the vehicle speed is 5 mph (8 km/h) or
higher, and the ECU receives no signals for 12 minutes or
more.
Tire pressure monitor receiver assy

Each tire pressure monitor valve sub±assy

Tire pressure monitor ECU

Wire harness
C2181/81
C2182/82
C2183/83
C2184/84
C2185/85
Malfunction in the transmitting/receiving circuit

Tire pressure monitor receiver assy

Each tire pressure monitor valve sub±assy

Tire pressure monitor ECU

Wire harness
HINT:
It is necessary to perform the procedure to identify the tire pressure monitor valve sub±assy that is malfunc-
tioning because it cannot be identified by the output DTC.
WIRING DIAGRAM