dimensions TOYOTA SEQUOIA HYBRID 2023 Owners Manual

2894-5. Using the driving support systems
Owners Manual_USA_M0C043_en
4
Driving
2 Press or to select
“Trailer Settings” and then
press and hold .
3 According to the display,
select the desired setting and
then press . ( P.102)
■Auto Trailer Detection (ATD)
Auto Trailer Detect ion (ATD) detects
if a trailer is attached by using the
Trailer Brake Controller (TBC) or the
Blind Spot Monitor (BSM) sensors.
●Trailers that use TBC can be
detected by using the 7-pin trailer
brake connectors.
●Other types of trailers can be
detected using the BSM sensors.
●When a trailer is detected via BSM
or TBC, RCTA function will be dis-
abled.
●As soon as the tra iler is detected,
the detectio n area will be
extended to a maximum length of
approximately 16 ft. (15 m) from
the rear bumper of the truck.
●If the trailer does not have a 7-pin
connector, or the 7-pin connector
is not engaged, the trailer is
detected via the BSM sensor. In
this case PKSB (i f equipped) and
Intuitive parking assist functions
will not be disabled.
●For trailer auto detection without
engagement of 7-pin connector,
the vehicle should be moving for-
ward at speed of above 0.6 mph
(1 km/h) for at least 10 seconds.
●ATD function is triggered at every
power switch on/off cycle or if the
vehicle is stopped in shift the shift
lever is in P or N for more than 90
seconds.
●Trailer detection vis BSM sensors
may be delayed if the vehicle is in
a crowded environment such as
busy parking lot, area surrounded
with trees (camping ground) or in
an environment with objects in the
immediate environment that pre-
vent sensors from sufficiently
detecting the trailer.
■Trailer Length Detection (TLD)
●Once a trailer is detected and if
the trailer length in the meter is
selected as “Auto”, the TLD func-
tion will estimate the trailer length
using the Blind Spot Monitor sen-
sors.
In order to estimate the trailer length
with TLD function and detection
area, make at least two 90 degree
turns.
If the trailer length is entered manu-
ally via multi-information display
input, the detection area is also
adjusted to exceed the length of the
trailer.
●Depending on some trailer types
and the dimensions of the trailer
TMW performance may be
degraded.

5488-1. Specifications
Owners Manual_USA_M0C043_en
8-1.Specifications
■2WD models
*1: Unladen vehicles
*2: Vehicles without TRD Sport Package
*3: Vehicles with TRD Sport Package
■4WD models
Maintenance data (fuel, oil level, etc.)
Dimensions and weight
Overall length208.1 in. (5285 mm)
Overall width79.8 in. (2021 mm)
Overall height*1
18 inch tires74.41 in. (1890 mm)
20 inch tires74.21 in. (1885 mm)*2
74.49 in. (1892 mm)*3
22 inch tires74.21 in. (1885 mm)
Wheelbase122.0 in. (3100 mm)
Front tread68.5 in. (1741 mm)*3
68.6 in. (1742 mm)*2
Rear tread68.4 in. (1737 mm)
Overall length208.1 in. (5285 mm)
Overall width79.8 in. (2021 mm)
Overall height*1
18 inch tires
74.13 in. (1883 mm)*2
74.33 in. (1888 mm)*3
74.57 in. (1894 mm)*4
77.68 in. (1973 mm)*4, 5
20 inch tires
74.21 in. (1885 mm)*6
74.45 in. (1891 mm)*7
74.41 in. (1890 mm)*8
22 inch tires74.45 in. (1891 mm)
Wheelbase122.0 in. (3100 mm)
Front tread68.6 in. (1742 mm)*9
69.6 in. (1767 mm)*4
Rear tread68.4 in. (1737 mm)*9
69.4 in. (1762 mm)*4

5628-1. Specifications
Owners Manual_USA_M0C043_en
Section width (millimeters)
Aspect ratio (tire height to
section width)
Tire construction code (R =
Radial, D = Diagonal)
Wheel diameter (inches)
Load index (2 digits or 3 dig-
its)
Speed symbol (alphabet with
one letter)
■Tire dimensionsSection width
Tire height
Wheel diameter Bead
Sidewall
Shoulder
Tread
Belt
Inner liner
Reinforcing rubber
Carcass
Rim lines
Bead wires
Chafer
This information has been pre-
pared in accordance with regu-
lations issued by the National
Highway Traffic Safety Adminis-
tration of the U.S. Department of
Transportation.
It provides the purchasers
and/or prospective purchasers
of Toyota vehicles with informa-
Tire section names
Uniform Tire Quality
Grading