trailer TOYOTA SUPRA 1997 Service Repair Manual

MA01F-02
MA-4
- MAINTENANCEUNDER HOOD
41 Author
: Date
:
1997 SUPRA (RM502U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item an cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the ºFULLº and ºLOWº lines on the see-through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see-through reservoirs.
7. ENGINE DRIVE BELT
Check drive belt for fraying, cracks, wear or oil contamination.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL

Check the level on the dipstick.

The level should be in the ºHOTº or ºCOLDº range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from ºPº to ºLº,
and then shift into ºPº position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re-insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 - 80°C, 158 - 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, have the cause located
and corrected.

TC00A-01
P11285
NO!
P13207
NO!
Ceramic
P11284
- TURBOCHARGING (2JZ-GTE)TURBOCHARGER
TC-3
1203 Author
: Date
:
1997 SUPRA (RM502U)
TURBOCHARGER
PRECAUTION
1. DO NOT STOP ENGINE IMMEDIATELY AFTER PULL-
ING A TRAILER OR AFTER HIGH SPEED OR UPHILL
DRIVING. IDLE ENGINE FOR 20 - 120 SECONDS, DE-
PENDING ON HOW HARD VEHICLE HAS BEEN DRIV-
EN
2. AVOID SUDDEN ACCELERATION OR RACING IM-
MEDIATELY AFTER STARTING A COLD ENGINE
3. DO NOT RUN ENGINE WITH AIR CLEANER RE-
MOVED, AS THIS MAY CAUSE FOREIGN MATERIAL
TO ENTER AND DAMAGE IMPELLER WHEEL OPER-
ATING AT HIGH SPEED
4. IF A TURBOCHARGER IS FOUND TO BE DEFECTIVE
AND MUST BE REPLACED, CHECK FOR CAUSE, AND
REPAIR OR REPLACE FOLLOWING ITEMS AS NEC-
ESSARY

Engine oil level and quality

Conditions under which the turbocharger was used

Oil lines leading to the turbocharger
5. USE CAUTION WHEN REMOVING AND REINSTAL-
LING TURBOCHARGER ASSEMBLY. DO NOT DROP
IT OR KNOCK IT AGAINST ANYTHING OR GRASP IT
BY EASILY-DEFORMED PARTS, SUCH AS ACTUA-
TOR OR ROD, WHEN MOVING IT
6. USE CAUTION WHEN REMOVING AND REINSTAL-
LING EXHAUST GAS CONTROL VALVE ASSEMBLY.
DO NOT DROP IT OR KNOCK IT AGAINST ANYTHING
OR GRASP IT BY EASILY-DEFORMED PARTS, SUCH
AS ACTUATOR OR ROD, WHEN MOVING IT. CON-
TROL VALVE IS CERAMIC
7. BEFORE REMOVING TURBOCHARGER, PLUG IN-
TAKE AND EXHAUST PORTS AND OIL INLET TO PRE-
VENT ENTRY OF DIRT OR OTHER FOREIGN MATERI-
AL
8. IF REPLACING TURBOCHARGER, CHECK FOR AC-
CUMULATION OF SLUDGE PARTICLES IN OIL PIPES,
AND IF NECESSARY, REPLACE OIL PIPES
9. COMPLETELY REMOVE GASKET ADHERED TO LU-
BRICATION OIL PIPE FLANGE AND TURBOCHAR-
GER OIL FLANGE
10. WHEN REPLACING BOLT OR NUTS, USE ONLY AU-
THORIZED REPLACEMENT PARTS TO PREVENT
BREAKAGE OR DEFORMATION