wheel TOYOTA SUPRA 1997 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1997, Model line: SUPRA, Model: TOYOTA SUPRA 1997Pages: 1807, PDF Size: 39.36 MB
Page 2 of 1807
CL-2
- CLUTCHTROUBLESHOOTING
1543 Author: Date:
1997 SUPRA (RM502U) Clutch slips
1. Clutch pedal (Freeplay out of adjustment)
2. Clutch disc (Oily)
3. Clutch disc (Worn out)
4. Diaphragm spring (Damaged)
5. Pressure plate (Distortion)
6. Flywheel (Distortion)CL-3
CL-15
CL-20
CL-15
CL-20
CL-15
CL-20
CL-15
CL-20
-
Clutch does not disengage
1. Clutch pedal (Freeplay out of adjustment)
2. Clutch line (Air in line)
3. Master cylinder cup (Damaged)
4. Release cylinder cup (Damaged)
5. Input shaft bearing (Worn, dirty or damaged)
6. Pilot bearing (Worn or damaged)
7. Clutch disc (Out of true)
8. Clutch disc (Runout is excessive)
9. Clutch disc (Lining broken)
10. Clutch disc (Dirty or burred)
11. Clutch disc (Oily)
12. Clutch disc (Lack of spline grease)
13. Diaphragm spring (Damaged)
14. Diaphragm spring (Out of tip alignment)
15. Pressure plate (Distortion)CL-3
-
CL-5
CL-10
-
CL-15
CL-20
CL-15
CL-20
CL-15
CL-20
CL-15
CL-20
CL-15
CL-20
CL-15
CL-20
CL-19
CL-25
CL-15
CL-20
CL-19
CL-25
CL-15
CL-20
Page 7 of 1807
CL04A-03
Q06260
Plate Washer
Wave Washer
Snap Ring
Clutch Thrust Cone Spring
Clutch Release Hub
Release Fork Support Clutch DiscClutch Release BearingPlate Washer
Release Fork Support Spring
E-Ring
Release Fork x9
Pilot BearingClutch Cover
Snap Ring
Wave
Washer Flywheel
Assembly
25 (260, 18)
19 (195, 14)
See page CL-22
N´m (kgf´cm, ft´lbf): Specified torque
Non-reusable part
Pin CL-20
- CLUTCHCLUTCH UNIT (2JZ-GTE)
1561 Author: Date:
1997 SUPRA (RM502U)
CLUTCH UNIT (2JZ-GTE)
COMPONENTS
Page 9 of 1807
CL04C-02
Q04200
Q04201
Q04202
Q04204
Q04206
CL-22
- CLUTCHCLUTCH UNIT (2JZ-GTE)
1563 Author: Date:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT CLUTCH DISC FOR WEAR OR DAMAGE
Using calipers, measure the rivet head depth.
Maximum rivet depth: 0.3 mm (0.012 in.)
If necessary, replace the clutch disc.
2. INSPECT CLUTCH DISC RUNOUT
Using a dial indicator, check the disc runout.
Maximum runout: 0.8 mm (0.031 in.)
If the runout is excessive, replace the clutch disc.
3. INSPECT FLYWHEEL RUNOUT
Using a dial indicator, check the flywheel runout.
Maximum runout: 0.1 mm (0.004 in.)
If the runout is excessive, replace the flywheel.
4. INSPECT PILOT BEARING
Turn the bearing by hand while applying force in the axial direc-
tion.
If the bearing sticks or has much resistance, replace the pilot
bearing.
5. IF NECESSARY, REPLACE PILOT BEARING
(a) Remove the 2 bolts at the diametrically opposite points.
Page 11 of 1807
Q04326
Matchmarks
Secondary
FlywheelPrimary
Flywheel
Q04327
Matchmarks CL-24
- CLUTCHCLUTCH UNIT (2JZ-GTE)
1565 Author: Date:
1997 SUPRA (RM502U)
8. INSPECT FLYWHEEL DAMPER FOR GREASE LEAK-
AGE
If grease has sprayed onto the clutch housing, replace the fly-
wheel assembly.
9. INSPECT FLYWHEEL DAMPER ROTATIONAL FREE-
PLAY
(a) Install the 2 bolts to the secondary flywheel at diametrical-
ly opposite positions.
(b) Holding both the bolts, and turn the secondary flywheel
clockwise until it stops.
(c) Put matchmarks on the primary and secondary flywheels
at this position.
(d) Then rotate the primary flywheel counterclockwise by
hand until it stops.
(e) Put matchmarks on the primary flywheel at this position.
(f) Measure the circumferential length between the 2 match-
marks on the secondary flywheel.
Standard: 105 mm (4.134 in.)
(g) Repeat the previous steps (d) to (f) 4 times and if the mea-
surement is greater than the maximum length replace the
flywheel assembly (See page EM-88).
Page 12 of 1807
CL04D-01
Z13786
SST Front
Q04210
SST 7
3
1, 4
2, 58 6 Matchmarks
Q06263
SST
Q04219
Q04403
- CLUTCHCLUTCH UNIT (2JZ-GTE)
CL-25
1566 Author: Date:
1997 SUPRA (RM502U)
INSTALLATION
1. INSTALL CLUTCH DISC AND COVER ON FLYWHEEL
(a) Insert SST in the clutch disc, then set them and the cover
in position.
SST 09301-001 10
(b) Align the matchmarks on the clutch cover and flywheel.
(c) Tighten the bolts evenly and gradually while pushing the
SST. Make several passes around the cover until it is
snug.
(d) Torque the bolts on the clutch cover in the order shown.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
HINT:
Temporarily tighten the No.1 and No.2 bolts.
2. CHECK DIAPHRAGM SPRING TIP ALIGNMENT
Using a dial indicator with roller instrument, check the dia-
phragm spring tip alignment.
Maximum non-alignment: 0.5 mm (0.020 in.)
If the alignment is not as specified, use SST to adjust the dia-
phragm spring tip alignment.
SST 09333-00013
3. REMOVE CLUTCH COVER AND CLUTCH DISC
4. INSTALL CLUTCH RELEASE FORK
(a) Install the wave washer and pin to release fork.
(b) Install a new E-ring.
5. APPLY MOLYBDENUM DISULPHIDE LITHIUM BASE
GREASE (NLGI NO.2)
(a) Apply release hub grease to these parts:
Release fork and hub contact point
Release fork and push rod contact point
Release fork pivot point
Page 15 of 1807
Q04160
Push Rod Play and
Freeplay Adjust Point
Pedal
HeightPedal Height
Adjust Point
Push Rod PlayCL03Z-01
CL0102Pedal Freeplay
Z13785
25 mm (0.98 in.) or more
Full Pedal Stroke Full Stroke
End PositionRelease
Point
- CLUTCHCLUTCH PEDAL
CL-3
1544 Author: Date:
1997 SUPRA (RM502U)
CLUTCH PEDAL
INSPECTION
1. CHECK PEDAL HEIGHT
Pedal height from asphalt sheet:
146.2 - 156.2 mm (5.76 - 6.15 in.)
2. IF NECESSARY, ADJUST PEDAL HEIGHT
Loosen the lock nut and clutch switch until the height is correct.
Tighten the lock nut.
HINT:
Before rotating the clutch switch for pedal height adjustment,
disconnect the clutch switch connector.
3. CHECK PEDAL FREEPLAY AND PUSH ROD PLAY
Push in on the pedal until the beginning of clutch resistance is
felt.
Pedal freeplay: 5.0 - 15.0 mm (0.197 - 0.591 in.)
Gently push on the pedal until the resistance begins to increase
a little.
Push rod play at pedal top:
1.0 - 5.0 mm (0.039 - 0.197 in.)
4. IF NECESSARY, ADJUST PEDAL FREEPLAY AND
PUSH ROD PLAY
(a) Loosen the lock nut and turn the push rod until the free-
play and push rod play are correct.
(b) Tighten the lock nut.
(c) After adjusting the pedal freeplay, check the pedal height.
5. INSPECT FULL PEDAL STROKE
Full pedal stroke: 132.0 - 138.0 mm (5.20 - 5.43 in.)
6. INSPECT CLUTCH RELEASE POINT
(a) Pull the parking brake lever and install wheel stopper.
(b) Start the engine and idle the engine.
(c) Without depressing the clutch pedal, slowly shift the shift
lever into the reverse position until the gears contact.
(d) Gradually depress the clutch pedal and measure the
stroke distance from the point the gear noise stops (re-
lease point) up to the full stroke end position.
Page 21 of 1807
MT06M-02
- MANUAL TRANSMISSION (V160)TROUBLESHOOTING
MT-1
1569 Author: Date:
1997 SUPRA (RM502U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
Noise
1. Flywheel damper
2. Oil (Level low)
3. Oil (Wrong)
4. Gear (Worn or damaged)
5. Bearing (Worn or damaged)CL-17
CL-22
MT-3
MT-3
-
-
Oil leakage
1. Oil (Level too high)
2. Gasket (Damaged)
3. Oil seal (Worn or damaged)
4. O-Ring (Worn or damaged)MT-3
-
MT-7
MT-2
MT-7
Hard to shift or will not shift1. Synchronizer ring (Worn or damaged)
2. Shift key spring (Damaged)-
-
Jumps out of gear
1. Locking ball spring (Damaged)
2. Shift fork (Worn)
3. Gear (Worn or damaged)
4. Bearing (Worn or damaged)-
-
-
-
Page 25 of 1807
Q04136Matchmarks
Q04137
Q04138
Q04341
Q04141
A
B
A
- MANUAL TRANSMISSION (V160)MANUAL TRANSMISSION UNIT
MT-5
1573 Author: Date:
1997 SUPRA (RM502U)
15. REMOVE CLUTCH COVER SET BOLT
(a) Remove the 2 bolts and service hole cover.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
(b) Place matchmarks on the flywheel and clutch cover.
(c) Remove the 6 bolts.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
16. JACK UP TRANSMISSION SLIGHTLY
Using a transmission jack, support the transmission.
17. REMOVE REAR ENGINE MOUNTING MEMBER
Remove the 4 nuts, bolts and rear engine mounting member.
Torque:
Nut: 13 N´m (135 kgf´cm, 10 ft´lbf)
Bolt: 25 N´m (260 kgf´cm, 19 ft´lbf)
18. REMOVE STARTER
Lower the engine rear side and remove the 2 bolts and starter.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
19. REMOVE TRANSMISSION
Remove the 5 transmission mounting bolts and transmission
from the engine.
Torque: 72 N´m (730 kgf´cm, 53 ft´lbf)
20. REMOVE SHIFT LEVER RETAINER
Remove the 5 bolts, nut and shift lever retainer from the trans-
mission.
Torque:
Bolt A: 19 N´m (195 kgf´cm, 14 ft´lbf)
Nut B: 25 N´m (250 kgf´cm, 18 ft´lbf)
21. REMOVE ENGINE REAR MOUNTING
Remove the 4 bolts and engine rear mounting from the trans-
mission.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
Page 52 of 1807
BE1367
Medium Current Fuse and High Current Fuse
Equal Amperage Rating
V00076
Abbreviation Part Name Symbol Illustration
FUSE
MEDIUM CURRENT FUSE
HIGH CURRENT FUSE
FUSIBLE LINK
CIRCUIT BREAKERFUSE
M-FUSE
H-FUSE
FL
CB
- INTRODUCTIONREPAIR INSTRUCTIONS
IN-5
5 Author: Date:
1997 SUPRA (RM502U)
(h) Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
(i) Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found in the preparation part at the front
of each section in this manual.
(j) When replacing fuses, be sure the new fuse has the cor-
rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.
(k) Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations (See page IN-8).
(1) If the vehicle is to be jacked up only at the front or
rear end, be sure to block the wheels at the opposite
end in order to ensure safety.
(2) After the vehicle is jacked up, be sure to support it
on stands. It is extremely dangerous to do any work
on a vehicle raised on a jack alone, even for a small
job that can be finished quickly.
Page 58 of 1807
B02917
- INTRODUCTIONFOR ALL OF VEHICLES
IN-1 1
11 Author: Date:
1997 SUPRA (RM502U)
(3) Even in cases of a minor collision where the SRS
does not deploy, the steering wheel pad, front pas-
senger airbag assembly and front airbag sensor
should be inspected (See page SR- 8, RS- 22,
RS-34).
(4) Never use SRS parts from another vehicle. When
replacing parts, replace them with new parts.
(5) Before repairs, remove the airbag sensor if shocks
are likely to be applied to the sensor during repairs.
(6) Never disassemble and repair the airbag sensor as-
sembly, steering wheel pad or front passenger air-
bag assembly in order to reuse it.
(7) If the airbag sensor assembly, steering wheel pad
or front passenger airbag assembly have been
dropped, or if there are cracks, dents or other de-
fects in the case, bracket or connector, replace
them with new ones.
(8) Do not expose the airbag sensor assembly, steer-
ing wheel pad and front passenger airbag assembly
directly to hot air or flames.
(9) Use a volt/ohmmeter with high impedance (10 kW/V
minimum) for troubleshooting of the electrical cir-
cuit.
(10) Information labels are attached to the periphery of
the SRS components. Follow the instructions on
the notices.
(11) After work on the supplemental restraint system is
completed, check the SRS warning light (See page
RS-1).
(c) SPIRAL CABLE (in Combination Switch)
The steering wheel must be fitted correctly to the steering
column with the spiral cable at the neutral position, other-
wise cable disconnection and other troubles may result.
Refer to of this manual concerning correct steering wheel
installation.