low beam TOYOTA SUPRA 1998 Owners Manual

SUPRA (U)
54
For high beam, push the lever away
from you. Pull it toward you for low
beam. For the headlight flasher, pull it
further back.
A blue light in the instrument panel indi-
cates high beam is on.
The headlight flasher works even when
the headlight switch is off.For signaling turns, move the lever up
or down in the conventional manner.
The key must be in the ºONº position.
The turn signal is self- cance lling after a
turn, but after a lane change, you may
have to cancel it by hand. You can also
signal a lane change by moving the turn
signal lever partway and holding it there.
If the green light in the instrument panel
flashes faster than normal, it indicates
that the front or rear turn signal bulb has
burned out. Emergency flashersTo turn on the emergency flashers,
push the switch.
All the turn signal lights will flash.
Turn on the emergency flashers to warn
other drivers if your vehicle must be
stopped where it might be a traffic hazard.
Always pull as far off the road as pos-
sible.
The turn signal light switch will not work
when the emergency flashers are operat-
ing.

SUPRA (U)55
NOTICE
To prevent the battery from being dis-charged, do not leave the switch onfor a long period when the engine isnot running.
Instrument panel light control
To adjust the brightness of the instru-
ment panel lights, turn the knob. Front fog lightsTo turn on the front fog lights, twist
the knob of the headlight and turn sig-
nal switch lever. They will come on
when the headlights are turned on low
beam.

SUPRA (U)175
Adding washer fluid
If any washer does not work, the wash-
er tank may be empty. Add washer
fluid.
You may use plain water as washer fluid.
However, in cold areas where tempera-
tures range below freezing point, use
washer fluid containing antifreeze. This
product is available at your Toyota dealer
and most auto parts stores. Follow the
manufacturer 's directions for how much to
mix with water.
NOTICE
Do not use engine antifreeze or any
other substitute because it may dam-age your vehicle's paint.
Checking the headlight aim
60500F11
Before checking the headlight aim: 1. Be sure that the body around the head- light is not deformed.
2. Park the vehicle on a level spot.
3. The driver gets into the driver's seat and puts the vehicle in a state ready-
ing for a driving (with a full tank).
4. Bounce the vehicle several times.60500F02
To check the headlight aim, check the
vertical and horizontal gauges. 1. Look at the beam angle gauge (vertical movement). The bubble of the gauge
should not deviate from the center of
the gauge by more than two marks on
either side of the gauge.

SUPRA (U)
176
60500F04
2. Look at the beam angle gauge (hori- zontal movement). The º0º mark should
not deviate by more than one mark on
either side of the gauge.
If the error is over the value specified
above, take the vehicle to your Toyota
dealer to adjust the headlight aim. Replacing light bulbsÐ
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the
wattage ratings given in the table.
CAUTION
Halogen bulbs have pressurized gas
inside and require special handling.
They can burst or shatter if scratched
or dropped. Hold a bulb only by its
plastic or metal case. Do not touch
the glass part of a bulb with barehands.
NOTICE
Only use a bulb of the listed type.
Light bulbsBulb
No.WTy p e
Headlight
(low beam)900655A
Headlight
(high beam)900565B
Front fog lights'55C
Parking lights'5E
Front turn signal lights744021E
Front side marker lights1943.8E
Rear side marker lights1943.8E
Rear turn signal lights744021E
Stop and tail lights744321/5E
Back- up lights744021E
License plate lightÐ5E
Interior lightsÐ8D
Glovebox lightÐ1.2E
Luggage compartment
lightÐ5F
A: HB4 halogen bulbs
B: HB3 halogen bulbs
C: H3 halogen bulbs
D: Single end bulbs
E: Wedge base bulbs
F: Double end bulbs

SUPRA (U)177
ÐHeadlights (low beam)
60463F38
1. Open the hood.
RIGHT SIDE HEADLIGHT: Release the
clips of the air cleaner and remove the
air cleaner cover.60463F39
2. Unplug the connector while depress- ing the lock release.
If the connector is tight, wiggle it.60473F05
3. Turn the bulb clockwise and remove it. Install a new bulb, turn it counter-
clockwise, then plug in the connec-
tor.
To install a bulb, align the tab of the bulb
socket with the cutouts of the mounting
hole.
RIGHT SIDE HEADLIGHT: Install the air
cleaner cover securely.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.