door lock TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine MA001−28
− MAINTENANCEOUTSIDE VEHICLE
MA−1
36 Author: Date:
1996 TOYOTA T100 (RM449U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts.
If necessary, tighten them.
4. TIRE ROTATION
Check the owner’s manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

Downloaded from www.Manualslib.com manuals search engine MA0568
B02099
B02100
− MAINTENANCECHASSIS
MA−13
48 Author: Date:
1996 TOYOTA T100 (RM449U)
12. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten these parts:
Seat mounting bolts
Torque:
37 N·m (375 kgf·cm, 27 ft·lbf)

2WD:
Strut bar bracket−to−frame mounting bolts
Torque: 52 N·m (530 kgf·cm, 38 ft·lbf)
Leaf spring U−bolt mounting nuts
Torque: 133 N·m (1,350 kgf·cm, 98 ft·lbf )
(b) Under Severe Conditions:
In addition to the above maintenance items, check for
loose or missing bolts and nuts on the following.
Steering system
Drive train
Suspension system
Fuel tank mounts
Engine mounts, etc.
13. FINAL INSPECTION
(a) Check operation of body parts:
Hood:
Auxiliary catch operates properly
Hood locks securely when closed
Doors:
Door locks operate properly
Doors close properly
Seats:
Seat adjusts easily and locks securely in any
positions
Seat backs lock securely at any angle
Fold−down seat backs lock securely
(b) Road test:
Engine and chassis parts do not have abnormal
noises.
Vehicle does not wander or pull to one side.
Brakes work properly and do not drag.

Downloaded from www.Manualslib.com manuals search engine SS−78
− SERVICE SPECIFICATIONSBODY ELECTRICAL
252 Author: Date:
1996 TOYOTA T100 (RM449U)B − C
Approx. 55.0 Ω
FUEL SENDER GAUGE
Float position mm (in.)Resistance (Ω)
F: Approx. 95 mmApprox. 3.0 Ω
1/2: Approx. 188.0 mmApprox. 32.5 Ω
E: Approx. 283.0 mmApprox. 110.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ Tachometer)Resistance (Ω)
A − BApprox. 150.0 Ω
A − CApprox. 54.0 Ω
B − CApprox. 138.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ o Tachometer)
A − BApprox. 25.0 Ω
OIL PRESSURE RECEIVER GAUGE
A − BApprox. 25.0 Ω
DOOR LOCK CONTROL RELAY (Wire Harness Side)
2 − Ground (Constant)Battery positive voltage
8 − Ground (Ignition Switch LOCK or ACC)No voltage
8 − Ground (Ignition Switch ON)Battery positive voltage
13 − Ground (Key unlock warning switch OFF (Ignition key removed))No voltage
13 − Ground (Key unlock warning switch ON (Ignition key set))Battery positive voltage
CRUISE CONTROL ECU (wire harness side)
24 − 26 (constant)Approx. 2.0 kΩ
25 − 26 (Actuator arm turned)Resistance change even
10 − Ground (Brake pedal position: Released)Approx. 38.0 Ω
10 − Ground (Brake pedal position: Depressed)No continuity
CRUISE CONTROL SWITCH
18 − Ground (Control switch position: OFF)No continuity
18 − Ground (Control switch position: RESUME/ACCEL)Approx. 68.0 Ω
18 − Ground (Control switch position: SET/COAST)Approx. 198.0 Ω
18 − Ground (Control switch position: CANCEL)Approx. 418.0 Ω
14 − Ground (Ignition switch position: LOCK or ACC)No voltage
14 − Ground (Ignition switch position: ON)Battery positive voltage
15 − Ground (Constant)Battery positive voltage
1 − Ground (Constant)Battery positive voltage
16 − Ground (Brake pedal position: Released)No voltage
16 − Ground (Brake pedal position: Depressed)Battery positive voltage
20 − Ground (With ignition switch ON, Speedsensor shaft turned)Valtage changes repeatedly
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2.0 kΩ
2 − 3 (The arm is moving from the closed to open position)Approx. 0.5 to 1.8 kΩ
ANTENNA MOTOR CONTROL RELAY (Wire harness side)
3 − Ground (Constant)Battery positive voltage
5 − Ground (Ignition Switch position: LOCK)No voltage
5 − Ground (Ignition switch position: ACC)Battery positive voltage
7 − Ground (Ignition switch position: LOCK)No voltage

Downloaded from www.Manualslib.com manuals search engine SS08Y−02
SS−80
− SERVICE SPECIFICATIONSBODY
254 Author: Date:
1996 TOYOTA T100 (RM449U)
BODY
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
FRONT BUMPER−−−
Front bumper arm x Body6162045
Bumper side support x Bumper arm131309
HOOD−−−
Hood hinge x Hood1414510
Hood lock x Body1919514
FRONT DOOR−−−
Door hinge x Body2526019
Door hinge x Door panel2526019
Door lock x Door panel5.96052 in.·lbf
Window regulator x Door panel5.45548 in.·lbf
FRONT WIPER AND WASHER−−−
Wiper arm x Wiper link2020415
TAIL GATE−−−
Tail gate lock striker x Body121209
Tail gate lock x Tail gate121209
Tail gate hinge x Tail gate1818513
FRONT SEAT (Bench Type)−−−
Seat track x Body3737527
Seat track x Seatback1818513
Outer track x Seat cushion frame1818513
Inner track x Seat cushion frame1818513
FRONT SEAT (Split Bench Type)−−−
Seat track x Body3737527
Seat adjuster x Seatback1818513
Outer track x Seat cushion frame1818513
Inner track x Seat cushion frame1818513
Seat adjuster x Seat cushion frame1818513
Inner track x Seat back frame12.51309.5
REAR SEAT−−−
Back panel trim x Body9.81007
Seat cushion x Body9.81007
SEAT BELT−−−
Front Seat Belt−−−
Adjustable anchor x Body4344032
Shoulder anchor x Adjustable anchor4344032
ELR x Body4344032
Lap outer anchor x Body4344032
Inner belt x Body4344032
Rear Seat Belt−−−
Shoulder anchor x Body4344032
ELR x Body4344032

Downloaded from www.Manualslib.com manuals search engine W03127
AT:
For 2WDParking Lock Cable
Steering Wheel
Steering Wheel Torx Screw
Steering Wheel Lower
No.2 CoverPad Control Shaft Column Upper
Cover
Lever
 Locking
Wire
Column Hole
CoverSteering Column Assembly
Steering Wheel Lower
No.3 Cover
Torx Screw
Combination Switch
(w/ Spiral Cable)
Column Lower Cover
Light Control Rheostat
Front Door Scuff
Plate Sliding w/ Shaft York
Sub−Assembly
Lower Finish Panel No.1
Intermediate
Shaft Assembly
Engine Hood Release
Lever
Duct Heater to
Register No.2
Intermediate
Shaft Assembly
Cowl Side Trim
 Non−reusable partControl Shaft Assembly
x35 (360, 26)
25 (260, 19)
35 (360, 26)
35 (360, 26)
35 (360, 26)
: Specified torque
N·m (kgf·cm, ft·lbf)
9.0 (90, 78 in.·lbf)
9.0 (90, 78 in.·lbf)
SR076−01
SR−10
− STEERINGNON−TILT STEERING COLUMN
1684 Author: Date:
1996 TOYOTA T100 (RM449U)
NON−TILT STEERING COLUMN
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine Q02574
Matchmarks
Cap Nut SR−14
− STEERINGNON−TILT STEERING COLUMN
1996 TOYOTA T100 (RM449U)
3. A/T:
REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 6 screws.
4. M/T:
REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 7 screws.
5. REMOVE LOWER FINISH PANEL NO.1
(a) Remove the 2 screws and disconnect the engine hood re-
lease lever from the panel.
(b) Remove the 4 screws and front door scuff plate.
(c) Remove the clip and cowl side trim.
(d) Remove the 4 panel set bolts.
(e) Remove the light control rheostat and lock nut.
6. REMOVE DUCT HEATER TO REGISTER NO.2
Remove the screw.
7. REMOVE COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Remove the 2 screws.
(b) Disconnect the connectors.
(c) Disconnect the airbag connector.
(d) Remove the 4 screws.
8. REMOVE SPIRAL CABLE
(See page BE−15)
NOTICE:
Do not disassemble the cable or apply oil to it.
9. A/T:
DISCONNECT PARKING LOCK CABLE
(a) Place the matchmarks on the cap nut and parking lock
cable.
(b) Loosen the cap nut.
(c) Disconnect the parking lock cable.

Downloaded from www.Manualslib.com manuals search engine R07644Red Mark
R07660
Torx ScrewScrew Case
− STEERINGNON−TILT STEERING COLUMN
SR−21
1996 TOYOTA T100 (RM449U)
9. INSTALL COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Install the 4 screws.
(b) Connect the airbag connector.
(c) Connect the connectors.
(d) Install the 2 screws.
10. INSTALL DUCT HEATER TO REGISTER NO.2
Install the screw.
11. INSTALL LOWER FINISH PANEL NO.1
(a) Install the lock nuts and light control rheostat.
(b) Tighten the 4 panel set bolts.
(c) Install the cowl side trim and clip.
(d) Install the front door scuff plate with the 4 screws.
(e) Install the engine hood release lever with the 2 screws.
12. A/T:
INSTALL UPPER AND LOWER COLUMN COVERS
Install the 6 screws.
13. M/T:
INSTALL UPPER AND LOWER COLUMN COVERS
Install the 7 screws.
14. CENTER SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Turn the spiral counterclockwise by hand until it becomes
harder to turn the cable.
(c) Then turn the spiral cable clockwise about 3 turns to align
the red mark.
HINT:
The spiral cable turns clockwise about 3 turns to either left or
right of the center.
15. INSTALL STEERING WHEEL
(a) Align the matchmarks on the wheel and main shaft.
(b) Torque the set nut.
Torque: 35 N·m (360 kgf·cm, 26 ft·lbf)
(c) Connect the connector.
16. INSTALL STEERING WHEEL PAD
NOTICE:
Make sure the wheel pad is installed to the specified
torque.
If the wheel pad has been dropped, or there are
cracks, dents in the case or connector, replace the
wheel pad with a new one.
When installing the wheel pad, take care that the wir-
ings do not interfere with other parts and are not
pinched between other parts.

Downloaded from www.Manualslib.com manuals search engine W03156
Column UpperParking Lock Cable
Torx Screw
Steering Wheel Lower
No.2 Cover
Control Shaft AssemblySteering Wheel
Steering Wheel
Steering Wheel Lower
No.3 Cover
Torx Screw
Combination Switch
(w/ Spiral Cable)
Column lower Cover
Light Control Rheostat
Front Door Scuff Steering Column
Assembly Control Shaft
 Locking
Column Hole
Sliding w/ Shaft York
Sub−Assembly
Lower Finish Panel No.1
Engine Hood Release Intermediate
Shaft Assembly
Register No.2 Duct Heater toPlatePad
Lever Cover
Wire
Cover
Lever AT:
For 2WD
Intermediate
Shaft Assembly
Cowl Side Trimx6
Non−reusable part35 (360, 26)
9.0 (90, 78 in.·lbf)
35 (360, 26)
35 (360, 26)
35 (360, 26)
35 (360, 26)
: Specified torque
N·m (kgf·cm, ft·lbf)
25 (260, 19)
25 (260, 19)
9.0 (90, 78 in.·lbf)
SR07C−01
− STEERINGTILT STEERING COLUMN
SR−23
1697 Author: Date:
1996 TOYOTA T100 (RM449U)
TILT STEERING COLUMN
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine BE – BODY ELECTRICAL

BODY ELECTRICAL SYSTEM BE-1
POWER SOURCE BE-10
IGNITION SWITCH AND KEY UNLOCK
WARNING SWITCH BE-11
HEADLIGHT AND TAILLIGHT SYSTEM BE-14
TURN SIGNAL AND HAZARD
WARNING SYSTEM BE-22
INTERIOR LIGHT SYSTEM BE-24
BACK-UP LIGHT SYSTEM BE-26
STOP LIGHT SYSTEM BE-29
WIPER AND WASHER SYSTEM BE-31
COMBINATION METER BE-35
POWER WINDOW CONTROL SYSTEM BE-46
POWER DOOR LOCK CONTROL
SYSTEM BE-50
POWER MIRROR CONTROL SYSTEM BE-56
AUDIO SYSTEM BE-59
ANTENNA BE-81
CLOCK BE-83

Downloaded from www.Manualslib.com manuals search engine BE01F−10
BE−2
− BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TOYOTA T100 (RM449U)
PROBLEM SYMPTOMS TABLE
The table below will be useful for you in troubleshooting these electrical problems. The most likely causes
of the malfunction are shown in the order of their probability. Inspect each part in the order shown, and re-
place the part when it is found to be faulty.
USA:
HEADLIGHT AND TAILLIGHT SYSTEM
SymptomSuspect AreaSee page
Headlight does not light up
(Taillight is normal)
1. HEAD Fuse (Relay Block)
2. Light Control Switch
3. Headlight Dimmer Switch
4. Headlight BulbBE−14
BE−17
BE−17
BE−17
Headlight does not light up
(Taillight does not light up)
1. Light Control Switch
2. Headlight Dimmer Switch
3. Wire Harness
4. Headlight BulbBE−17
BE−17
−
−
Only one light comes on
1. HEAD Fuse (Relay Block)
2. Wire Harness
3. Headlight BulbBE−14
−
−
”Lo−Beam” does not light up
1. Headlight Control Relay
2. Headlight Dimmer Relay
3. Headlight Dimmer Switch
4. Wire Harness
5. Headlight BulbBE−17
BE−17
BE−17
−
−
”Hi−Beam” does not light up
1. Headlight Control Relay
2. Headlight Dimmer Relay
3. Headlight Dimmer Switch
4. Wire Harness
5. Headlight BulbBE−17
BE−17
BE−17
−
−
”Flash” does not light up
1. Headlight Control Relay
2. Headlight Dimmer Relay
3. Headlight Dimmer Switch
4. Wire Harness
5. Headlight BulbBE−17
BE−17
BE−17
−
−
Taillight does not light up
(Headlight does not light up)
1. TAIL Fuse (Junction Block No.1)
2. Light Control Switch
3. Wire Harness
4. Headlight BulbBE−17
BE−17
−
−
Taillight does not light up
(Headlight is normal)
1. TAIL Fuse (Junction Block No.1)
2. Light Control Switch
3. Taillight Control Relay
4. Wire Harness
5. Taillight BulbBE−14
BE−17
BE−17
−
−
Only one light goes out or does not light up1. Wire Harness
2. Taillight Bulb−
−
Rear Combination light does not light up
1. TAIL Fuse (Junction Block No.1)
2. Wire Harness
3. Taillight BulbBE−14
−
−
”Light−on warning system” does not operate.
1. Integration Relay
2. DOME Fuse (Relay Block)
3. GAUGE Fuse (Junction Block No.1)
4. Door Courtesy Switch
5. Wire HarnessBE−17
BE−14
BE−14
BE−25
−