engine coolant TOYOTA T100 1996 Factory Service Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: T100, Model: TOYOTA T100 1996Pages: 2062, PDF Size: 43.47 MB
Page 25 of 2062
Downloaded from www.Manualslib.com manuals search engine DTC No.
Indicates the diagnostic trouble code.
Page or Instructions
Indicates the page where the inspection procedure
for each circuit is to be found, or gives instructions
for checking and repairs.
Detection Item
Indicates the system of the problem or
contents of the problem. Trouble Area
Indicates the suspect area of the
problem.
Mass Air Flow Circuit MalfunctionDetection Item
Open or short in mass air flow meter circuit
Mass air flow meter
ECM DTC No.
(See page)Trouble AreaMIL*MemoryP0100
(DI − 26)
P0101
(DI − 31)Mass Air Flow Circuit
Range/Performance Problem Mass air flow meter
P0115
(DI − 37) Open or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM Intake Air Temp. Circuit Malfunction P0110
(DI − 32)
Engine Coolant Temp. Circuit
Range/Performance Problem Open or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM
P0120
(DI − 43)
Throttle/ Pedal Position Sensor/Switch
”A” Circuit Range/Performance
P0116
(DI − 41)
Throttle/Pedal Position Sensor/Switch
”A” Circuit Malfunction
Insufficient Coolant Temp. for Closed Engine coolant temp. sensor
Cooling system Engine Coolant Temp. Circuit
Malfunction
Open or short in throttle position sensor circuit
Throttle position sensor
ECM
Throttle position sensor
Open or short in heated oxygen sensor circuit
Heated oxygen sensor
DTC CHART (SAE Controlled)
HINT: Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check mode, check the circuit for that code listed in the table
below. For details of each code, turn to the page referred to under the ”See page” for the respective ”DTC No.”
in the DTC chart.
IN−22− INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
1996 TOYOTA T100 (RM449U)
4. DIAGNOSTIC TROUBLE CODE CHART
The inspection procedure is shown in the table below. This table permits efficient and accurate troubleshoot-
ing using the diagnostic trouble codes displayed in the diagnostic trouble code check. Proceed with trouble-
shooting in accordance with the inspection procedure given in the diagnostic chart corresponding to the
diagnostic trouble codes displayed. The engine diagnostic trouble code chart is shown below as an example.
Page 34 of 2062
Downloaded from www.Manualslib.com manuals search engine IN02L−01
− INTRODUCTIONTERMS
IN−31
31 Author: Date:
1996 TOYOTA T100 (RM449U)
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti−Lock Brake System
A.D.D.Automatic Disconnecting Differential
A/TAutomatic Transmission
AT FAutomatic Transmission Fluid
BTDCBefore Top Dead Center
Calif.California
CBCircuit Breaker
Diff.LockDifferential Locking System
DPDash Pot
ECUElectronic Control Unit
E/GEngine
ELREmergency Locking Retractor
ESAElectronic Spark Advance
EXExhaust (Manifold, Valve)
FIPGFormed in Place Gasket
FLFusible Link
FPUFuel Pressure Up
FrFront
IGIgnition
INIntake (Manifold, Valve)
J/BJunction Block
LHLeft−Hand
LLCLong Life Coolant (Year Around Coolant)
LSPVLoad Sensing Proportioning Valve
Max.Maximum
Min.Minimum
MPMultipurpose
M/TManual Transmission
O/D, ODOverdrive
OHCOver Head Camshaft
O/SOversize
PCVPositive Crankcase Ventilation
PSPower Steering
RHRight−Hand
RrRear
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
SWSwitch
TDCTop Dead Center
TEMP.Temperature
Page 36 of 2062
Downloaded from www.Manualslib.com manuals search engine IN02M−01
− INTRODUCTIONTERMS
IN−33
1996 TOYOTA T100 (RM449U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE−J1930 terms and abbreviations used in this manual in compliance with SAE rec-
ommendations, as well as their Toyota equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOTA TERMS
( )−−ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal−
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric Pressure−
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection−
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position−
CTOXContinuous Trap Oxidizer−
CTPClosed Throttle Position−
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition−
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode−
ECLEngine Control Level−
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionDistributorless Ignition (DI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control−
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory−
FEPROMFlash Erasable Programmable Read Only Memory−
FFFlexible Fuel−
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
Page 43 of 2062
Downloaded from www.Manualslib.com manuals search engine MA003−05
MA−4
− MAINTENANCEUNDER HOOD
39 Author: Date:
1996 TOYOTA T100 (RM449U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see−through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see−through reservoirs.
7. ENGINE DRIVE BELTS
Check all drive belts for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re−insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 − 80°C, 158 − 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
(a) Visually inspect for cracks, holes or loose supports.
(b) If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, have the cause
located and corrected.
Page 44 of 2062
Downloaded from www.Manualslib.com manuals search engine MA004−03
P08488
Back Front
− MAINTENANCEENGINE
MA−5
40 Author: Date:
1996 TOYOTA T100 (RM449U)
ENGINE
INSPECTION
HINT:
Inspect these items when the engine is cold.
1. (5VZ−FE ENGINE)
REPLACE TIMING BELT
(See page EM−11 )
2. INSPECT DRIVE BELTS
GENERATOR:
(3RZ−FE: See page CH−2)
(5VZ−FE: See page CH−1)
PS:
(3RZ−FE: See page SR−3)
(5VZ−FE: See page SR−3)
A/C:
(3RZ−FE: See page AC−14)
(5VZ−FE: See page AC−14)
3. REPLACE SPARK PLUGS
(3RZ−FE: See page IG−1)
(5VZ−FE: See page IG−1)
4. INSPECT AIR FILTER
(a) Visually check that the air cleaner element is not exces-
sively dirty, damaged or oily.
HINT:
Oiliness may indicate a stuck PCV valve.
If necessary, replace the air cleaner element.
(b) Clean the element with compressed air.
First blow from back side thoroughly, then blow off the
front side of the element.
5. REPLACE AIR FILTER
Replace the used air cleaner element with a new one.
6. REPLACE ENGINE OIL AND OIL FILTER
(3RZ−FE: See page LU−3)
(5VZ−FE: See page LU−3)
7. REPLACE ENGINE COOLANT
(3RZ−FE: See page CO−2)
(5VZ−FE: See page CO−
2)
8. CALIFORNIA, MASSACHUSETTS, MAIN, VERMONT,
RHODE ISLAND and NEW HAMPSHIRE:
INSPECT CHARCOAL CANISTER
(3RZ−FE: See page EC−5)
(5VZ−FE: See page EC−5)
9. REPLACE GASKET IN FUEL TANK CAP
(3RZ−FE: See page EC−5)
(5VZ−FE: See page EC−5)
Page 81 of 2062
Downloaded from www.Manualslib.com manuals search engine PP0GG−01
− PREPARATIONCOOLING (3RZ−FE)
PP−27
1996 TOYOTA T100 (RM449U)
COOLANT
ItemCapacityClassification
Engine coolant
(w/ Heater)8.7 liters (9.2 US qts, 7.7 lmp. qts)Ethylene−glycol base
Page 85 of 2062
Downloaded from www.Manualslib.com manuals search engine PP336−02
− PREPARATIONCOOLING (5VZ−FE)
PP−31
1996 TOYOTA T100 (RM449U)
COOLANT
ItemCapacityClassification
2WD
M/T
A/T
4WD
M/T
A/T
10.0 liters (10.6 US qts, 8.8 lmp. qts)
9.9 liters (10.5 US qts, 8.7 lmp. qts)
10.0 liters (10.6 US qts, 8.8 lmp. qts)
10.2 liters (10.8 US qts, 9.0 lmp. qts)
Ethylene−glycol base
Page 188 of 2062
Downloaded from www.Manualslib.com manuals search engine SS−8
− SERVICE SPECIFICATIONSENGINE MECHANICAL (3RZ−FE)
1996 TOYOTA T100 (RM449U) Oil strainer x Cylinder block
1818513
Oil pan x Cylinder block12.51309
Crankshaft position sensor x Timing chain cover8.58574 in.·lbf
Generator bracket x Cylinder block74.576055
Generator bracket x Timing chain cover1818513
Generator adjusting bar x Timing chain cover63.565047
A/C compressor bracket x Cylinder block4444032
A/C compressor x A/C compressor bracket2525018
Water pump pulley x Water pump2121016
Connecting rod cap x Connecting rod 1st
2nd45
Turn 90°46033
Main bearing cap x Cylinder block 1st
2nd39
Turn 90°40029
No.1 balance shaft x Timing gear3636526
No.2 balance shaft x Timing sprocket3636526
Balance shaft x Cylinder block1818513.4
Rear oil seal retainer x Cylinder block13.51359.7
RH, LH engine mounting bracket x Cylinder block4545034
Oil dipstick guide x LH engine mounting bracket2020014
Oil filter bracket union, Engine coolant drain plug x Cylinder block2525018
Oil filter bracket x Cylinder block2829021
Water bypass pipe x Cylinder block2020014
Knock sensor x Cylinder block3738027
Fuel filter x Cylinder block2020014
Rear end plate x Cylinder block1818513
Rear end plate x Water bypass pipe2020014
Flywheel x Crankshaft 1st
2nd26.5
Turn 90°27019
Front crossmember x Engine rear mounting bracket2526019
Front exhaust pipe clamp x Exhaust manifold6263046
Exhaust support bracket x Transmission3940029
Front exhaust pipe clamp1919514
Front exhaust pipe x TWC3940029
Engine rear mounting bracket x Engine rear mounting insulator1818313
Engine front mounting insulator x Frame3838728
Clutch release cylinder bracket x Transmission3940029
Clutch release cylinder x Transmission131309
Stabilizer bar bracket mounting bolt3030622
Stabilizer bar x Lower suspension arm131309
Intake air connector x Cylinder head1818513
Radiator x Body1818513
Page 192 of 2062
Downloaded from www.Manualslib.com manuals search engine SS00P−11
SS−12
− SERVICE SPECIFICATIONSENGINE MECHANICAL (5VZ−FE)
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
No.1 idler pulley x Oil pump3535026
No.2 idler pulley x No.2 idler pulley bracket4040030
No.1 timing belt cover x Oil pump99080 in.·lbf
Crankshaft pulley x Crankshaft2502,500184
Camshaft timing pulley x Camshaft11 01,10081
Timing belt tensioner x Oil pump2727020
No.2 timing belt cover x No.3 timing belt cover99080 in.·lbf
Oil dipstick guide x Generator bracket88071 in.·lbf
Fluid coupling x Fan bracket5.45448 in.·lbf
Camshaft bearing cap x Cylinder head1616012
Rear plate x Cylinder head88071 in.·lbf
Cylinder head x Cylinder block 12 pointed head 1st
2nd
3rd
Recessed head34
Turn 90°
Turn 90°
18350
Turn 90°
Turn 90°
18525
Turn 90°
Turn 90°
13
Cylinder head cover x Cylinder head66053 in.·lbf
Exhaust manifold x Cylinder head4040030
Exhaust manifold heat insulator x Exhaust manifold88071 in.·lbf
Exhaust crossover pipe x Exhaust manifold4545033
Generator bracket x LH cylinder head18.518514
PS pump bracket x RH cylinder head4444032
Intake manifold x Cylinder head1818013
Intake manifold stay x Intake manifold18.518513
Intake manifold stay x No. 2 idler pulley bracket18.518513
No.3 timing belt cover x Cylinder head99080 in.·lbf
Camshaft position sensor x RH cylinder head88071 in.·lbf
Intake air connector x Intake manifold18.518513
Air intake chamber x Intake air connector18.518513
Air intake chamber stay x LH cylinder head, Air intake chamber4040030
EGR pipe x LH exhaust manifold18.518513
EGR pipe x EGR valve18.518513
EGR pipe x Cylinder head88071 in.·lbf
Engine hanger No.2 x RH cylinder head4040030
Frame crossmember x Engine rear mounting bracket5859043
Engine rear mounting bracket x Engine rear mounting insulator1818513
Engine front mounting insulator x Frame3838728
Connecting rod cap x Connecting rod 1st
2nd25
Turn 90°250
Turn 90°18
Turn 90°
Main bearing cap x Cylinder block 1st
2nd61
Turn 90°625
Turn 90°45
Turn 90°
Rear oil seal retainer x Cylinder block88071 in.·lbf
Oil cooler union x Cylinder block3030022
Oil hole cover plate x Cylinder block6060044
Engine coolant drain cock x Cylinder block3940029
Page 258 of 2062
Downloaded from www.Manualslib.com manuals search engine SS−78
− SERVICE SPECIFICATIONSBODY ELECTRICAL
252 Author: Date:
1996 TOYOTA T100 (RM449U)B − C
Approx. 55.0 Ω
FUEL SENDER GAUGE
Float position mm (in.)Resistance (Ω)
F: Approx. 95 mmApprox. 3.0 Ω
1/2: Approx. 188.0 mmApprox. 32.5 Ω
E: Approx. 283.0 mmApprox. 110.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ Tachometer)Resistance (Ω)
A − BApprox. 150.0 Ω
A − CApprox. 54.0 Ω
B − CApprox. 138.0 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE (w/ o Tachometer)
A − BApprox. 25.0 Ω
OIL PRESSURE RECEIVER GAUGE
A − BApprox. 25.0 Ω
DOOR LOCK CONTROL RELAY (Wire Harness Side)
2 − Ground (Constant)Battery positive voltage
8 − Ground (Ignition Switch LOCK or ACC)No voltage
8 − Ground (Ignition Switch ON)Battery positive voltage
13 − Ground (Key unlock warning switch OFF (Ignition key removed))No voltage
13 − Ground (Key unlock warning switch ON (Ignition key set))Battery positive voltage
CRUISE CONTROL ECU (wire harness side)
24 − 26 (constant)Approx. 2.0 kΩ
25 − 26 (Actuator arm turned)Resistance change even
10 − Ground (Brake pedal position: Released)Approx. 38.0 Ω
10 − Ground (Brake pedal position: Depressed)No continuity
CRUISE CONTROL SWITCH
18 − Ground (Control switch position: OFF)No continuity
18 − Ground (Control switch position: RESUME/ACCEL)Approx. 68.0 Ω
18 − Ground (Control switch position: SET/COAST)Approx. 198.0 Ω
18 − Ground (Control switch position: CANCEL)Approx. 418.0 Ω
14 − Ground (Ignition switch position: LOCK or ACC)No voltage
14 − Ground (Ignition switch position: ON)Battery positive voltage
15 − Ground (Constant)Battery positive voltage
1 − Ground (Constant)Battery positive voltage
16 − Ground (Brake pedal position: Released)No voltage
16 − Ground (Brake pedal position: Depressed)Battery positive voltage
20 − Ground (With ignition switch ON, Speedsensor shaft turned)Valtage changes repeatedly
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2.0 kΩ
2 − 3 (The arm is moving from the closed to open position)Approx. 0.5 to 1.8 kΩ
ANTENNA MOTOR CONTROL RELAY (Wire harness side)
3 − Ground (Constant)Battery positive voltage
5 − Ground (Ignition Switch position: LOCK)No voltage
5 − Ground (Ignition switch position: ACC)Battery positive voltage
7 − Ground (Ignition switch position: LOCK)No voltage