water pump TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine IN02M−01
− INTRODUCTIONTERMS
IN−33
1996 TOYOTA T100 (RM449U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE−J1930 terms and abbreviations used in this manual in compliance with SAE rec-
ommendations, as well as their Toyota equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOTA TERMS
( )−−ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal−
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric Pressure−
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection−
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position−
CTOXContinuous Trap Oxidizer−
CTPClosed Throttle Position−
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition−
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode−
ECLEngine Control Level−
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionDistributorless Ignition (DI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control−
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory−
FEPROMFlash Erasable Programmable Read Only Memory−
FFFlexible Fuel−
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)

Downloaded from www.Manualslib.com manuals search engine PP0G6−01
PP−2
− PREPARATIONENGINE MECHANICAL (3RZ−FE)
51 Author: Date:
1996 TOYOTA T100 (RM449U)
ENGINE MECHANICAL (3RZ−FE)
SST (Special Service Tools)
09032−00100Oil Pan Seal Cutter
09201−10000Valve Guide Bushing Remover &
Replacer Set
(09201−01060)Valve Guide Bushing Remover &
Replacer 6
09202−70020Valve Spring Compressor
09207−76010Rocker Arm Bushing
09213−54015Crankshaft Pulley Holding Tool
09223−15030Oil Seal & Bearing ReplacerCrankshaft rear oil seal
09223−50010Crankshaft Front oil Seal
Replacer
09236−00101Water Pump Overhaul Tool Set
(09236−15010)Bearing StayValve stem oil seal
09248−55040Valve Clearance Adjust Tool Set
(09248−05410)Valve Lifter Press

Downloaded from www.Manualslib.com manuals search engine PP3K3−01
− PREPARATIONSTEERING
PP−103
152 Author: Date:
1996 TOYOTA T100 (RM449U)
STEERING
SST (Special Service Tools)
09223−46011Crankshaft Front Oil Seal
ReplacerIdler arm
09236−00101Water Pump Overhaul Tool Set
(09237−00010)Water Pump Bearing Remover &
ReplacerPS gear (2WD)
09608−04031Front Hub Inner Bearing Cone
ReplacerPS vane pump (3RZ−FE)
09610−20012Pitman Arm PullerSteering linkage
09611−22012Tie Rod End PullerSteering linkage
09612−00012Rack & Pinion Steering Rack
Housing StandPS gear (2WD)
09612−22011Tilt Handle Bearing ReplacerPS gear (2WD)
09612−24014Steering Gear Housing Overhaul
Tool Set
(09613−22011)Steering Rack Shaft Bushing
PullerPS gear (2WD)
09612−65014Steering Worm Bearing Puller
(09612−01030)Claw ”C”PS gear (4WD)

Downloaded from www.Manualslib.com manuals search engine SS093−02
− SERVICE SPECIFICATIONSENGINE MECHANICAL (3RZ−FE)
SS−7
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Throttle body x Air intake chamber2020014
Spark plug x Cylinder head1920014
Cylinder head x Cylinder block 1st
2nd
3rd39
Turn 90°
Turn 90°
40029
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head15.516012
Camshaft timing gear x Camshaft73.575054
Distributor gear x Camshaft4646534
Chain tensioner x Cylinder head2121015
Engine hanger x Cylinder head4242030
Exhaust manifold x Cylinder head4950036
Heat insulator x Exhaust manifold5.55548 in.·lbf
Front exhaust pipe x Exhaust manifold6263046
No.1 support bracket x Transmission3940029
No.1 support bracket clamp bolt1919514
Front exhaust pipe x TWC3940029
Intake manifold x Cylinder head2930022
Delivery pipe x Intake manifold2121015
Fuel inlet tube x Fuel filter2930022
Fuel inlet tube x Delivery pipe2930022
EGR valve x Air intake chamber, EGR pipe1919514
EGR vacuum modulator x Air intake chamber8.58574 in.·lbf
EGR pipe x Exhaust manifold2020015
EGR pipe x Cylinder head1818514
Cylinder head rear cover x Cylinder head13.513510
Water outlet x Cylinder head2020014
PS pump bracket x Cylinder head2020014
PS pump bracket x PS pump5859043
PS pump x PS pump pulley4344032
PS pump idler pulley x Cylinder head2020014
Balance shaft drive gear x Balance shaft2525018
No.2 chain tensioner, No.3 vibration damper x Cylinder block1818513
No.2 vibration damper x Cylinder block2727020
No.1 vibration damper x Cylinder block1818513
No.1 timing chain tensioner slipper x Cylinder block2727020
Timing chain cover x Cylinder block Bolt A
Bolt B
Bolt C
Nut D20
24.5
44
20200
250
440
20014
18
32
14
Timing chain cover mounting bolt1818513
No.1 water bypass pipe mounting nut2020014
Crankshaft pulley x Crankshaft2602,650193
No.2 and No.3 crankshaft pulley x Crankshaft pulley2525018

Downloaded from www.Manualslib.com manuals search engine SS−8
− SERVICE SPECIFICATIONSENGINE MECHANICAL (3RZ−FE)
1996 TOYOTA T100 (RM449U) Oil strainer x Cylinder block
1818513
Oil pan x Cylinder block12.51309
Crankshaft position sensor x Timing chain cover8.58574 in.·lbf
Generator bracket x Cylinder block74.576055
Generator bracket x Timing chain cover1818513
Generator adjusting bar x Timing chain cover63.565047
A/C compressor bracket x Cylinder block4444032
A/C compressor x A/C compressor bracket2525018
Water pump pulley x Water pump2121016
Connecting rod cap x Connecting rod 1st
2nd45
Turn 90°46033
Main bearing cap x Cylinder block 1st
2nd39
Turn 90°40029
No.1 balance shaft x Timing gear3636526
No.2 balance shaft x Timing sprocket3636526
Balance shaft x Cylinder block1818513.4
Rear oil seal retainer x Cylinder block13.51359.7
RH, LH engine mounting bracket x Cylinder block4545034
Oil dipstick guide x LH engine mounting bracket2020014
Oil filter bracket union, Engine coolant drain plug x Cylinder block2525018
Oil filter bracket x Cylinder block2829021
Water bypass pipe x Cylinder block2020014
Knock sensor x Cylinder block3738027
Fuel filter x Cylinder block2020014
Rear end plate x Cylinder block1818513
Rear end plate x Water bypass pipe2020014
Flywheel x Crankshaft 1st
2nd26.5
Turn 90°27019
Front crossmember x Engine rear mounting bracket2526019
Front exhaust pipe clamp x Exhaust manifold6263046
Exhaust support bracket x Transmission3940029
Front exhaust pipe clamp1919514
Front exhaust pipe x TWC3940029
Engine rear mounting bracket x Engine rear mounting insulator1818313
Engine front mounting insulator x Frame3838728
Clutch release cylinder bracket x Transmission3940029
Clutch release cylinder x Transmission131309
Stabilizer bar bracket mounting bolt3030622
Stabilizer bar x Lower suspension arm131309
Intake air connector x Cylinder head1818513
Radiator x Body1818513

Downloaded from www.Manualslib.com manuals search engine SS099−01
SS−22
− SERVICE SPECIFICATIONSCOOLING (3RZ−FE)
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Cylinder block x Drain plug2425018
Fluid coupling x Fan5.55549 in.·lbf
Water pump x Cylinder block expect bolt A
for bolt A8.9
24.590
25078 in.·lbf
18
Water inlet x Water inlet housing2020015
Radiator support x Radiator tank M/T
A/T13
5.5130
569
49 in.·lbf
Radiator mounting bolt3131023

Downloaded from www.Manualslib.com manuals search engine SS00Z−06
SS−24
− SERVICE SPECIFICATIONSCOOLING (5VZ−FE)
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Fan x Fan pulley bracket5.45548 in.·lbf
Water pump x Cylinder block − Short bolt2020014
Water inlet x Water pump2020014
Radiator support x Body121208.7

Downloaded from www.Manualslib.com manuals search engine EM06Z−03
P14842
Adjusting Bolt
Lock Bolt
Pivot Bolt
P14935
P14907A03721
P14953
EM−14
− ENGINE MECHANICAL (3RZ−FE)TIMING CHAIN
1996 TOYOTA T100 (RM449U)
REMOVAL
1. DRAIN ENGINE OIL
2. DRAIN ENGINE COOLANT
3. REMOVE CYLINDER HEAD
(See page EM−28)
4. REMOVE ENGINE UNDER COVER
Remove the 4 bolts and engine under cover.
5. w/ A/C:
REMOVE A/C COMPRESSOR DRIVE BELT
Loosen the idler pulley nut and adjusting bolt, and remove the
drive belt.
6. REMOVE DRIVE BELT, FAN WITH FLUID
COUPLING, WATER PUMP PULLEY AND FAN
SHROUD
(a) Stretch the belt and loosen the water pump pulley mount-
ing nuts.
(b) Loosen the lock, pivot and adjusting bolts of the genera-
tor, and remove the drive belts.
(c) Remove the 4 water pump pulley mounting nuts.
(d) Pull out the fan with fluid coupling and water pump pulley.
(e) Remove the No.2 fan shroud.
(f) Remove the 4 bolts and No.1 fan shroud.
7. w/ A/C:
DISCONNECT A/C COMPRESSOR AND BRACKET
(a) Remove the 4 mounting bolts, and disconnect the com-
pressor from the bracket.
HINT:
Put a side the compressor, and suspend it.
(b) Remove the 4 bolts and A/C compressor bracket.
8. REMOVE GENERATOR, ADJUSTING BAR AND
BRACKET
(a) Remove the lock, pivot bolts and the generator.
(b) Remove the bolt and adjusting bar.
(c) Remove the 3 bolts and bracket.
9. REMOVE CRANKSHAFT POSITION SENSOR
(a) Remove the 2 bolts and crankshaft position sensor.
(b) Remove the O−ring from the crankshaft position sensor.

Downloaded from www.Manualslib.com manuals search engine P14907A03766
P14935
P14842
Adjusting Bolt
Lock Bolt
Pivot Bolt
− ENGINE MECHANICAL (3RZ−FE)TIMING CHAIN
EM−25
1996 TOYOTA T100 (RM449U)
(c) Install the generator with the pivot bolt and lock bolt.
13. w/ A/C:
INSTALL A/C COMPRESSOR AND BRACKET
(a) Install the A/C compressor bracket with the 4 bolts.
Torque: 44 N·m (440 kgf·cm, 32 ft·lbf)
(b) Install the A/C compressor with the 4 bolts.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
14. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN
WITH FLUID COUPLING AND DRIVE BELT
(a) Place the fan with fluid coupling, water pump pulley and
fan shroud in position.
(b) Temporarily install the water pump pulley mounting nuts.
(c) Install the No.1 fan shroud with the 4 bolts.
(d) Install the No.2 fan shroud with the 2 clips.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belt tight and tighten the 4 water pump pulley
mounting nuts.
Torque: 21 N·m (210 kgf·cm, 16 ft·lbf)
(g) Adjust the drive belts.
15. w/ A/C:
INSTALL A/C COMPRESSOR DRIVE BELT
Install and adjust the drive belt (See page CH−2).
16. INSTALL ENGINE UNDER COVER
Install the engine under cover with the bolts.
17. INSTALL CYLINDER HEAD (See page EM−50)
18. START ENGINE AND CHECK FOR LEAKS

Downloaded from www.Manualslib.com manuals search engine P15813
P15755SST
P14841
Adjusting Bolt
Look Bolt
P24651
− ENGINE MECHANICAL (3RZ−FE)CYLINDER HEAD
EM−59
1996 TOYOTA T100 (RM449U)
ECT sensor connector
Oil pressure sensor connector
w/ A/C:
A/C compressor connector
28. INSTALL THROTTLE BODY (See page MF−30)
29. INSTALL WATER OUTLET
(a) Install a new gasket and water outlet with the 2 bolts.
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(b) Connect the ECT sender gauge connector.
(c) Connect the radiator inlet hose.
30. INSTALL IGNITION COIL.
31. INSTALL NO.1 AND NO.2 PCV HOSES
32. INSTALL PS PUMP AND BRACKET
(a) Install the PS pump bracket with the 4 bolts.
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(b) Connect the PS pump to the bracket with the 2 bolts.
Torque: 58 N·m (590 kgf·cm, 43 ft·lbf)
(c) Connect the 2 air hoses to the intake chamber.
(d) Using SST, install the PS pump pulley with the nut.
SST 09960−10010 (09962−01000, 09963−01000)
Torque: 43 N·m (440 kgf·cm, 32 ft·lbf)
33. INSTALL PS PUMP DRIVE BELT AND IDLER
PULLEY
(a) Install the idler pulley with the 3 bolts.
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(b) Install and adjust drive belt (See page CH−2).
34. INSTALL AIR INTAKE CONNECTOR
(a) Install the air intake connector with the 2 bolts and hose
clamp.
(b) Connect the 2 air hoses.
35. M/T:
CONNECT ACCELERATOR CABLE TO THROTTLE
BODY
36. A/T:
CONNECT THROTTLE AND ACCELERATOR CABLES
TO THROTTLE BODY