four wheel drive TOYOTA TACOMA 2001 Owners Manual (in English)

’01 Tacoma U (L/O 0009)
72001 TACOMA (OM35766U)
∗1: For details, see Service reminder indicators and warning
buzzers" in Section 1−5.
∗2: If this light flashes, see Cruise control" in Section 1−6. Cruise control indicator light
∗
2
Rear differential lock indicator light
Four−wheel drive indicator light

’01 Tacoma U (L/O 0009)
1212001 TACOMA (OM35766U)
OPERATION OF INSTRUMENTS AND
CONTROLS
Ignition switch, Transmission and Parking brake
Ignition switch with steering lock122
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission 123
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
.
Manual transmission 128
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . .
Four−wheel drive system 130
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
Rear differential lock system 134
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake 136
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . .
Cruise control 137
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . .
Clutch start cancel switch 139
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
SECTION 1− 6

’01 Tacoma U (L/O 0009)
1242001 TACOMA (OM35766U)
(b) Overdrive switch
You can select either third gear (with
overdrive off) or fourth gear (with over-
drive on) by pushing this switch.
To turn the overdrive off, push the switch.
The O/D OFF" indicator light should come
on. To turn the overdrive on again, push
the switch again. The O/D OFF" indicator
light should go off.
Always drive your vehicle with the over-
drive on for better fuel economy and
quieter driving.
If the engine is turned off when the over-
drive is off and restarted, the overdrive
will be on automatically.Vehicles with cruise controlWhen the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking will not be enabled because the
cruise control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise control" in this section.
(c) Normal driving
1. Start the engine as instructed in How to start the engine" in Section 3. The
transmission must be in P" or N".
When the front drive control lever is in
L4" (low−speed position, four−wheel
drive), the driving pattern selector setting
has no effect on gear shift timing. (See
Four−wheel drive system" in this section
for information of the front drive control
lever.)
2. With your foot holding down the brake pedal, shift the selector lever to D".
When the lever is in the D" position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc. Always turn the overdrive switch on for
better fuel economy and quieter driving. If
the engine coolant temperature is low or
when the front drive control lever is in
L4" (low−speed position, four−wheel
drive), the transmission will not shift into
the overdrive gear even with the overdrive
on. (See Four−wheel drive system" in this
section for information of the front drive
control lever.)
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.
(d) Using engine braking
To use engine braking, you can downshift
the transmission as follows:
Push the overdrive switch. The O/D
OFF" indicator light will come on and
the transmission will downshift to third
gear.

’01 Tacoma U (L/O 0009)
1252001 TACOMA (OM35766U)
Shift into the 2" position. The trans-
mission will downshift to second gear
when the vehicle speed drops down to
or lower than the following speed, and
stronger engine braking will be en-
abled.
Two−wheel drive models except Pre
Runner2RZ−FE engine 105 km/h (65 mph)
. . . . . . . . . . . . .
Four−wheel drive models and Pre Run-
ner Front drive control lever in H2" and
H4"3RZ−FE engine 106 km/h (66 mph)
. . . . . . . . . . . . .
5VZ−FE engine
114 km/h (71 mph)
. . . . . . . . . . . . .
Front drive control lever in L4" 3RZ−FE engine 36 km/h (22 mph)
. . . . . . . . . . . . . .
5VZ−FE engine 38 km/h (24 mph)
. . . . . . . . . . . . . . Shift into the L" position. The trans-
mission will downshift to first gear
when the vehicle speed drops down to
or lower than the following speed, and
maximum engine braking will be en-
abled.
Two−wheel drive models except Pre
Runner
2RZ−FE engine 55 km/h (34 mph)
. . . . . . . . . . . . . .
Four−wheel drive models and Pre Run-
ner Front drive control lever in H2" and
H4"3RZ−FE engine 51 km/h (32 mph)
. . . . . . . . . . . . . .
5VZ−FE engine
55 km/h (34 mph)
. . . . . . . . . . . . . .
Front drive control lever in L4" 3RZ−FE engine 9 km/h (6 mph)
. . . . . . . . . . . . . . . . . .
5VZ−FE engine 10 km/h (6 mph)
. . . . . . . . . . . . . . . . .
Vehicles with cruise controlWhen the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking is not enabled because the cruise
control is not cancelled. For ways to decrease the vehicle speed,
see Cruise control" in this section.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
(e) Using 2" and L" positions
The 2" and L" positions are used for
strong engine braking as described pre-
viously.
With the selector lever in 2" or L", you
can start the vehicle in motion as with the
lever in D".
With the selector lever in 2", the vehicle
will start in first gear and automatically
shift to the second gear.
With the selector lever in L", the trans-
mission is engaged in first gear.

’01 Tacoma U (L/O 0009)
1262001 TACOMA (OM35766U)
NOTICE
Be careful not to over−rev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The approximate maximum al-
lowable speed for each position is
given below for your reference:
Two−wheel drive models except Pre
Runner 2RZ−FE engine 2" 122 km/h (75 mph) . . . . . . . .
L" 64 km/h (39 mph) . . . . . . . .
Four−wheel drive models Front drive control lever in H2" or
H4"
3RZ−FE engine2" 113 km/h (70 mph) . . . . . . . .
L" 62 km/h (38 mph) . . . . . . . .
5VZ−FE engine 2" 119 km/h (73 mph) . . . . . . . .
L" 65 km/h (40 mph) . . . . . . . .
Front drive control lever in L4"
3RZ−FE engine2" 44 km/h (27 mph) . . . . . . . . .
L" 24 km/h (14 mph) . . . . . . . . .
5VZ−FE engine 2" 65 km/h (40 mph) . . . . . . . . .
L" 25 km/h (16 mph) . . . . . . . . .
Pre Runner models
3RZ−FE engineRegular cab2" 119 km/h (73 mph) . . . . . .
L" 65 km/h (40 mph) . . . . . .
Xtra−cab and double cab 2" 113 km/h (70 mph) . . . . . .
L" 62 km/h (38 mph) . . . . . .
5VZ−FE engine 2" 119km/h (73 mph) . . . . . . . .
L" 65 km/h (40 mph) . . . . . . . .
 Do not continue hill climbing for a
long time in the 2" or L" posi-
tion. This may cause severe auto-
matic transmission damage from
overheating. To prevent such dam-
age, use D" position for hill climb-
ing or hard towing.(f) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the
R" position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(g) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever fully to securely apply the parking brake.
3. With the brake pedal pressed down, shift the selector lever to the P" posi-
tion.
CAUTION
Never attempt to move the selector
lever into P" position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.

’01 Tacoma U (L/O 0009)
1272001 TACOMA (OM35766U)
(h) Good driving practice
If the transmission repeatedly shifts up
and down between third gear and over-
drive when climbing a gentle slope, the
overdrive should be turned off. Be sure
to turn the switch on immediately after-
ward.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.
CAUTION
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.
NOTICE
Do not hold the vehicle on an up-
grade with the accelerator pedal. It
can cause the transmission to over-
heat. Always use the brake pedal or
parking brake.
(i) Driving in POWER" mode (four−wheel drive models and Pre
Runner)
In the POWER" mode, the transmission
is shifted up and down at a higher vehicle
speed than in the NORMAL" mode and a
more powerful acceleration is achieved. To
set the POWER" mode, push in the driv-
ing pattern selector button. The POWER
mode indicator light comes on.
For ordinary driving, Toyota recommends
using the NORMAL" mode to improve fuel
economy. (j) Rocking your vehicle if stuck
CAUTION
If your vehicle becomes stuck in
snow, mud, sand, etc., then you may
attempt to rock the vehicle free by
moving it forward and backward. Do
not attempt this procedure if people
or objects are anywhere near the ve-
hicle. During the rocking operation
the vehicle may suddenly move for-
ward or backward as it becomes un-
stuck, causing injury or damage to
nearby people or objects.

’01 Tacoma U (L/O 0009)
1292001 TACOMA (OM35766U)
3RZ−FE engineUpshifting gear km/h(mph)
1 to 2 24(15)
2 to 3 40(25)/58(36)
∗
3 to 4 64(40)/72(45)∗
4 to 5 72(45)/85(53)∗
Downshifting gear km/h(mph)
2 to 1 24(15)
3 to 2 40(25)
4 to 3 64(40)
5 to 4 72(45)
∗: Applicable under heavy acceleration
conditions.
5VZ−FE engine
gear km/h(mph)
1 to 2 or 2 to 1 24(15)
2 to 3 or 3 to 2 40(25)
3 to 4 or 4 to 3 64(40)
4 to 5 or 5 to 4 72(45)
Downshift to the appropriate gear if accel-
eration is needed when you are cruising
below the above downshifting speeds. Upshifting too soon or downshifting too
late will cause lugging, and possibly ping-
ing. Regularly revving the engine to maxi-
mum speed in each gear will cause ex-
cessive engine wear and high fuel
consumption.
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
Two−wheel drive models
2RZ−FE engine gear km/h(mph)1 48(29)
2 89(55)
3 137(85)
4 165(103)
5VZ−FE engine gear km/h(mph)
1 54(33)
2 101(62)
3 146(90)
4 180(111)\b Four−wheel drive models
3RZ−FE engine
gear km/h(mph)
H2" and H4" L4"
1 46(28) 17(10)
2 85(52) 33(20)
3 132(81) 51(31)
4 165(102) 70(43)
5VZ−FE engine gear km/h(mph) H2" and H4" L4"
1 47(29) 18(11)
2 88(54) 34(21)
3 127(78) 49(30)
4 165(102) 70(44)
NOTICE
Do not downshift if you are going
faster than the maximum allowable
speed for the next lower gear.

’01 Tacoma U (L/O 0009)
1302001 TACOMA (OM35766U)
Good driving practice
If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use fifth gear.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
NOTICE
Make sure the vehicle is completely
stopped before shifting into reverse.
Use the front drive control lever to se-
lect the following transfer modes.
H2" (high speed position, two−wheel
drive): Lever at H2"
Use this for normal driving on dry hard−
surfaced roads. This position gives greater
economy, quietest ride and least wear.
H4" (high speed position, four−wheel
drive): Lever at H4"
Use this for normal driving on wet, icy or
snow−covered roads. This position pro-
vides greater traction than two−wheel
drive. N" (neutral position):
Lever at N"
No power is delivered to the wheels. The
vehicle must be stopped.
L4" (low speed position, four−wheel
drive): Lever at L4"
Use this for maximum power and traction.
Use L4" for climbing or descending steep
hills, off−road driving, and hard pulling in
sand, mud or deep snow.
The four−wheel drive indicator light comes
on when the H4", N" or L4" mode is
selected.
See (c) Shifting procedure (lever type)"
for further instructions.
Four−wheel drive system
(a) Front drive control
(lever type)

’01 Tacoma U (L/O 0009)
1312001 TACOMA (OM35766U)
Use the front drive control lever and
4WD" button to select the following
transfer modes.
H2" (high speed position, two−wheel
drive): Lever at H", 4WD" button left out
Use this for normal driving on dry hard−
surfaced roads. This position gives greater
economy, quietest ride and least wear.
H4" (high speed position, four−wheel
drive): Lever at H", 4WD" button pushed
in.
Use this for normal driving on wet, icy or
snow−covered roads. This position pro-
vides greater traction than two−wheel
drive. N" (neutral position):
Lever at N"
No power is delivered to the wheels. The
vehicle must be stopped.
L4" (low speed position, four−wheel
drive): Lever at L4"
Use this for maximum power and traction.
Use L4" for climbing or descending steep
hills, off−road driving, and hard pulling in
sand, mud or deep snow.
The four−wheel drive indicator light comes
on when the H4", N" or L4" mode is
selected.
See (c) Shifting procedure (lever/button
type)" for further instructions.Ty p e A
Ty p e B
(a) Front drive control
(lever/button type) (b) A.D.D. (automatic
disconnecting differential)

’01 Tacoma U (L/O 0009)
1322001 TACOMA (OM35766U)
Ty p e C
The A.D.D. can be engaged or disen-
gaged by the shifting operations de-
scribed in (c) Shifting procedure".
You should drive in four−wheel drive for
at least 16 km (10 miles) each month.
This will assure that the front drive com-
ponents are lubricated.SHIFTING BETWEEN H2" AND H4"
To shift from H2" to H4",
reduce your
speed to less than 80 km/h (50 mph) and
move the front drive control lever. You
need not depress the clutch pedal.
If you have trouble shifting in cold weath-
er, reduce your speed or stop the vehicle
and reshift.
CAUTION
Never move the front drive control
lever if wheels are slipping. Stop the
slipping or spinning before shifting.
To shift from H4" to H2", simply move
the front drive control lever.
This can be done at any vehicle speed.
You need not depress the clutch pedal.
If the indicator light does not go off when
you shift the transfer into H2", drive
straight ahead while accelerating or decel-
erating, or drive in reverse. SHIFTING BETWEEN H4" AND L4"
To shift from H4" to L4",
stop the
vehicle or reduce your speed to less than
8 km/h (5 mph). With your foot off the
accelerator pedal, depress the clutch ped-
al and move the front drive control lever.
To shift from L4" to H4", depress the
clutch pedal and move the front drive con-
trol lever.
This can be done at any vehicle speed.
(c) Shifting procedure
(lever type with manual
transmission)