clock TOYOTA TACOMA 2008 Owners Manual (in English)

5
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
1. Front fog light switch
2. Rear differential lock switch
3. Power outlet main switch
4. Instrument panel light control dial
5. Headlight and turn signal switches
6. Audio remote control switches
7. Wiper and washer switches
8. Front drive control switch knob
9. Audio system
10. Clock
11. Engine immobilizer system indicator light
12. Front passenger ’s seat belt reminder light
13. Front passenger occupant classification indicator lights or passenger airbag on −
off indicator lights
14. Passenger airbag off switch
15. Air conditioning controls
16. Power outlet
17. Emergency flasher switch
18. Cigarette lighter
19. Parking brake lever (manual transmission)
LS11004b

31
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
LS12037
1. To open the fuel filler door, pull thedoor toward out as shown.
When refueling, turn off the engine.
CAUTION
Do not smoke, cause sparks or al-
low open flames when refueling.
The fumes are flammable.
When opening the cap, do not re-
move the cap quickly. In hot weath-
er, fuel under pressure could cause
injury by spraying out of the filler
neck if the cap is suddenly re-
moved.
Do not fill a fuel container in the
bed under any circumstances. A
static electricity charge could cause
a spark and fire hazard. The proper
procedure is to place an approved
fuel container on the ground away
from the truck for filling.
LS12038b
2. To remove the fuel tank cap, turnthe cap counterclockwise by 90 de-
grees (to the pressure point 1), and
then turn it an additional 30 degrees
(to point 2). Pause slightly before
removing it.
It is not unusual to hear a slight swoosh
when the cap is opened.
When installing the cap, turn the cap
clockwise until you hear a click. When
you hear the click, the cap is fully
closed.
If the cap is not tightened securely, the
malfunction indicator lamp comes on.
Make sure the cap is tightened securely.

55
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
LS13141a
Indicator light
The passenger airbag system is
equipped with a off switch and indica-
tor light. Turning the passenger airbag
off switch clockwise to the “AUTO”
position makes the front passenger air-
bag system operational. To disable the
front passenger airbag system, turn the
off switch counterclockwise to the
“OFF” position and remove the key. The
“OFF” indicator light will come on
when the front passenger airbag system
has been disabled.
See “Passenger airbag off switch” on page
70 in this Section for detail.
CAUTION
Do not turn off the passenger air-
bag off switch except when a mem-
ber of a passenger risk group iden-
tified in TABLE 1 is occupying the
front passenger seating position.
When the passenger airbag off
switch is turned off, the front pas-
senger airbag will not inflate in a
collision and turning off the front
passenger airbag can reduce the
occupant protection which your ve-
hicle safety systems can provide to
you in certain accidents and in-
crease the likelihood of death or
serious injuries.

71
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
Operate off switch as follows:
Insert key into the keyhole.
To turn the front passenger airbag
on—Turn the key clockwise to the “AUTO”
position. At this time, the indicator light
condition varies depending on the
occupant in the front passenger seat. (For
details, see “Front passenger occupant
classification system” on page 82 in this
Section.)
To turn the front passenger airbag
off—Turn the key counterclockwise to the
“OFF” position and remove it. At this time,
the “OFF” indicator light comes on. If the
key is removed at any other position than
“OFF”, the switch will automatically return
to the “AUTO” position.
LS13140
The SRS warning light and the passen-
ger airbag onoff indicator light will in-
dicate “OFF” if there is a malfunction
in the passenger airbag off switch.
CAUTION
Do not turn off the passenger air-
bag off switch except when a mem-
ber of a passenger risk group iden-
tified in TABLE 1 is occupying the
front passenger seating position.
When the passenger airbag off
switch is turned off, the front pas-
senger airbag will not inflate in a
collision and turning off the front
passenger airbag can reduce the
occupant protection which your ve-
hicle safety systems can provide to
you in certain accidents and in-
crease the likelihood of death or
serious personal injuries.
For details, see “SRS driver airbag
and front passenger airbag” on page
53 in this Section.

97
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
LS13005
CAUTION
Never install a rearfacing child re-
straint system on the front seat with
the passenger airbag off switch in the
“AUTO” position. In the event of an
accident, the force of the rapid infla-
tion of the front passenger airbag can
cause death or serious injury to the
child if the rearfacing child restraint
system is installed on the front pas-
senger seat.
LS13006a
When you install a rearfacing child re-
straint system which belongs to a pas-
senger risk group on the front passen-
ger seat, turn the passenger airbag off
switch counterclockwise to the “OFF”
position and remove the key. (For de-
tails, see “SRS driver airbag and front
passenger airbag” on page 53 in this
Section.)
The indicator light comes on when the
system is off.
CAUTION
If you must install a rearfacing child
restraint system on the front passen-
ger seat, make sure that the front
passenger airbag off switch is in the
“OFF” position with the key removed
and that the indicator light is on.

101
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
LS13006a
When you install a rearfacing child re-
straint system which belongs to a pas-
senger risk group on the front passen-
ger seat, turn the passenger airbag off
switch counterclockwise to the “OFF”
position and remove the key. (For de-
tails, see “SRS driver airbag and front
passenger airbag” on page 53 in this
Section.)
The indicator light comes on when the
system is off.
CAUTION
If you must install a rearfacing child
restraint system on the front passen-
ger seat, make sure that the passen-
ger airbag off switch is in the “OFF”
position with the key removed and
that the indicator light is on.
CAUTION
Forwardfacing child restraint system:
A forwardfacing child restraint
system which belongs to a passenger
risk group should never be installed
on the front passenger seat with the
passenger airbag off switch in the
“AUTO” position, because the force
of the deploying airbag could cause
death or serious injury to the child in
forward seating position. (For details,
see “SRS driver airbag and front
passenger airbag” on page 53 in this
Section.)

177
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
SHIFTING BETWEEN “H2” AND “H4”
To shift from “H2” to “H4”, reduce the
vehicle speed to less than 100 km/h (62
mph) and turn the front drive control
switch knob fully clockwise.
If the four −wheel drive indicator light con-
tinues to blink when you operate the front
drive control switch knob from the “H2” to
the “H4” position, this reminds you that
the transfer mode is not securely in “H4”
mode. Drive straight ahead while acceler-
ating or decelerating.
If the four −wheel drive indicator light con-
tinues to blink and the buzzer sounds
when you operate the front drive control
switch knob from the “H2” to the “H4”
position, this reminds you that the transfer
mode is not in “H4” mode. Stop the ve-
hicle or reduce the vehicle speed to less
than 100 km/h (62 mph). Operate the
switch knob again.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
To shift from “H4” to “H2”, turn the
front drive control switch knob fully coun-
terclockwise.
This can be done at any speed. You need
not depress the clutch pedal.
If the four −wheel drive indicator light con-
tinues to blink when you operate the front
drive control switch knob from the “H4” to
the “H2” position, this reminds you that
the transfer mode is not securely in “H2”
mode. Drive straight ahead while acceler-
ating or decelerating, or drive forward or
backward in a short distance.
If the indicator light continues to blink
even if doing so, contact your Toyota
dealer as soon as possible. There may be
a trouble in the four −wheel drive system.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
SHIFTING BETWEEN “H4” AND “L4”
To shift from “H4” to “L4”.
(1) Stop the vehicle or reduce the vehicle
speed to less than 3 km/h (2 mph).
(2) Depress the clutch pedal all the way.
(3) Push and turn the front drive control switch knob fully clockwise.
If the four −wheel drive indicator light
flashes and the buzzer sounds, try the
above steps again.
To shift from “L4” to “H4”.
(1) Stop the vehicle or reduce the vehicle
speed to less than 3 km/h (2 mph).
(2) Depress the clutch pedal all the way.
(3) Turn the front drive control switch knob fully counterclockwise.
If the four −wheel drive indicator light
flashes and the buzzer sounds, try the
above steps again.
If the “4LO” (low speed four −wheel drive)
indicator light continues to blink when you
operate the front drive control switch knob
to the “H4” or “L4” position, drive forward
or backward in a short distance, then stop
the vehicle completely, depress the clutch
pedal and operate the switch knob again.
(c) Shifting procedure (with
manual transmission)

178
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
If the indicator continues to blink even if
doing so, contact your Toyota dealer as
soon as possible. There may be a trouble
in the four−wheel drive system.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
SHIFTING BETWEEN “H2” AND “H4”
To shift from “H2” to “H4”, reduce the
vehicle speed to less than 100 km/h (62
mph) and turn the front drive control
switch knob fully clockwise.
If the four −wheel drive indicator light con-
tinues to blink when you operate the front
drive control switch knob from the “H2” to
the “H4” position, this reminds you that
the transfer mode is not securely in “H4”
mode. Drive straight ahead while acceler-
ating or decelerating.
If the four −wheel drive indicator light con-
tinues to blink and the buzzer sounds
when you operate the front drive control
switch knob from the “H2” to the “H4”
position, this reminds you that the transfer
mode is not in “H4” mode. Stop the ve-
hicle or reduce the vehicle speed to less
than 100 km/h (62 mph). Operate the
switch knob again.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
To shift from “H4” to “H2”, turn the
front drive control switch knob fully coun-
terclockwise.
This can be done at any speed.
If the four −wheel drive indicator light con-
tinues to blink when you operate the front
drive control switch knob from the “H4” to
the “H2” position, this reminds you that
the transfer mode is not securely in “H2”
mode. Drive straight ahead while acceler-
ating or decelerating, or drive forward or
backward in a short distance.
If the indicator light continues to blink
even if doing so, contact your Toyota
dealer as soon as possible. There may be
a trouble in the four −wheel drive system.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
(c) Shifting procedure (with
automatic transmission)

179
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
SHIFTING BETWEEN “H4” AND “L4”
To shift from “H4” to “L4”.
(1) Bring the vehicle to a complete stopwith the brake pedal held down with
your foot.
(2) Shift the automatic transmission selec- tor lever into “N”.
(3) Push and turn the front drive control switch knob fully clockwise.
If the four −wheel drive indicator light
flashes and the buzzer sounds, try the
above steps again.
To shift from “L4” to “H4”.
(1) Bring the vehicle to a complete stop with the brake pedal held down with
your foot.
(2) Shift the automatic transmission selec- tor lever into “N”.
(3) Turn the front drive control switch knob counterclockwise.
If the four −wheel drive indicator light
flashes and the buzzer sounds, try the
above steps again. If the “4LO” (low speed four
−wheel drive)
indicator light continues to blink when you
operate the front drive control switch knob
to the “H4” or “L4” position, drive forward
or backward in a short distance, then stop
the vehicle completely, shift the automatic
transmission selector lever securely into
“N” and operate the switch knob again.
If the indicator continues to blink even if
doing so, contact your Toyota dealer as
soon as possible. There may be a trouble
in the four −wheel drive system.
CAUTION
Never operate the front drive control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
The traction control system automatical-
ly helps prevent the spinning of rear
wheels (twowheel drive models) or 4
wheels (fourwheel drive models) when
the vehicle is started or accelerated on
slippery road surfaces.
When the engine switch is turned to “ON”,
the system automatically turns on.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicle and
power to the rear wheels (twowheel
drive models) or 4 wheels (fourwheel
drive models) cannot be maintained,
even though the traction control sys-
tem is in operation. Do not drive the
vehicle under any speed or maneuver-
ing conditions which may cause the
vehicle to lose traction control. In si-
tuations where the road surface is
covered with ice or snow, your ve-
hicle should be fitted with snow tires
or tire chains. Always drive at an ap-
propriate and cautious speed for the
present road conditions.
Traction control system

201
2008 TACOMA from Apr. ’08 Prod. (OM35898U)
When parking, firmly apply the parking
brake to avoid inadvertent creeping.
Pedal type—
To set: Fully depress the parking brake
pedal. For better holding power, first de-
press the brake pedal and hold it while
setting the parking brake.
To release: Depress the parking brake
pedal once again.
Lever type—
To set: Pull out on the lever. For better
holding power, first depress the brake
pedal and hold it while setting the parking
brake.
To release: Press the lock release button
(1), turn the lever clockwise (2), then
push it in (3).
To remind you that the parking brake is
set, the parking brake reminder light in
the instrument panel remains on until you
release the parking brake.
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
The cruise control is designed to main-
tain a set cruising speed without requir-
ing the driver to operate the accelera-
tor. Cruising speed can be set to any
speed above 40 km/h (25 mph).
Within the limits of the engine’s capabili-
ties, cruising speed can be maintained up
or down grades. However, changes in ve-
hicle speed may occur on steeper grades.
CAUTION
To help maintain maximum control
of your vehicle, do not use the
cruise control when driving in
heavy or varying traffic, or on slip-
pery (rainy, icy or snowcovered) or
winding roads.
Avoid vehicle speed increases when
driving downhill. If the vehicle
speed is too fast in relation to the
cruise control set speed, cancel the
cruise control then downshift the
transmission to use engine braking
to slow down.
LS17020b
TURNING THE SYSTEM ON AND OFF
To turn the cruise control on, press the
“ON−OFF” button. The “CRUISE” indicator
light on the instrument panel will come on
to indicate that the cruise control is opera-
tional. Pressing the “ON −OFF” button
again turns the system off.
When the system is turned off, cruising
speed must be reset when the cruise con-
trol is turned on again.
When the engine switch is turned off, the
system is also automatically turned off. To
use the cruise control again, press the
“ON −OFF” button again to turn it on.
Cruise control