ESP TOYOTA TERCEL 1996 Service User Guide

FI2553
SST
FI4429
Plug MF-2
- MFIMFI SYSTEM
526 Author
: Date
:
1996 TERCEL (RM440U)
(b) When installing the battery, be especially careful not to in-
correctly connect the positive (+) and negative (-) cables.
(c) Do not permit parts to receive a severe impact during re-
moval or installation. Handle all MFI parts carefully, espe-
cially the ECM.
(d) Do not be careless during troubleshooting as there are
numerous transistor circuits and contact with terminals
can cause further trouble.
(e) Do not open the ECM cover.
(f) When inspecting during rainy weather, take care to pre-
vent the entry of water. Also, when washing the engine
compartment, prevent water from getting on the MFI parts
and wiring connectors.
(g) Parts should be replaced as an assembly.
(h) Care is required when pulling out and inserting wiring con-
nectors.
(i) Release the lock and pull out the connector, pulling on the
connectors.
(j) Fully insert the connector and check that it is locked.
(k) When inspecting a connector with a volt/ohmmeter.
(l) Carefully take off the water-proofing rubber if it is a wa-
ter-proof type connector.
(m) Insert the tester probe into the connector from the wiring
side when checking the continuity, amperage or voltage.
(n) Do not apply unnecessary force to the terminal.
(o) After checking, install the water-proofing rubber securely
on the connector.
(p) Use SST for inspecting or testing the injector or its wiring
connector.
SST 09842-30070
8. FUEL SYSTEM
(a) When disconnecting the high fuel pressure line, a large
amount of gasoline will spill out, so observe these proce-
dures:
(1) Disconnect the fuel pump connector.
(2) Start the engine. After the engine has stopped on
its own, turn the ignition switch.
(3) Put a container under the connection.
(4) Slowly loosen the connection.
(5) Disconnect the connection.
(6) Plug the connection with a rubber plug.
(7) Reconnect the fuel pump connector.

ST0J1-01
P13459
Terminal 50
Terminal C
Battery
P13460
Terminal C
Battery
Disconnect
P13461
Battery
Disconnect
P13462
Battery
Ammeter Terminal 50
Terminal 30
- STARTINGSTARTER (Reduction Type)
ST-13
1996 TERCEL (RM440U)
TEST
NOTICE:
These tests must be performed within 3 to 5 seconds to
avoid burning out the coil.
1. DO HOLD-IN TEST
(a) Disconnect the field coil lead wire from terminal C.
(b) Connect the battery to the magnetic switch as shown.
Check that the clutch pinion gear moves outward.
2. DO HOLD-IN TEST
With battery connected as above with the clutch pinion gear
out, disconnect the negative (-) lead from terminal C. Check
that the pinion gear remains out.
3. INSPECT CLUTCH PINION GEAR RETURN
Disconnect the negative (-) lead from the switch body.
Check that the clutch pinion gear returns inward.
4. DO NO-LOAD PERFORMANCE TEST
(a) Connect the battery and ammeter to the starter as shown.
(b) Check that the starter rotates smoothly and steadily with
the pinion gear moving out. Check that the ammeter the
current specified in the respective repair manual.

N00173
SST
SST
CM0061
MT0092
SST
- MANUAL TRANSAXLEDIFFERENTIAL CASE
MX-39
1996 TERCEL (RM440U)
3. INSTALL SIDE BEARING
(a) Install the speedometer drive gear to the RH side.
(b) Using SST and a press, install new side bearings to the
both sides of the case.
SST 09350-32014 (09351-32090, 09351-32120)
4. INSPECT DIFFERENTIAL SIDE BEARING PRELOAD
(a) Install the differential case assembly to the transaxle
case.
(b) Install the transmission case.
(c) Install and torque the case bolts.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
(d) Using SST and a torque wrench, measure the preload.
SST 09564-3201 1
Preload (at starting):
New bearing
0.8 - 1.6 N´m (8 - 16 kgf´cm, 6.9 - 13.9 in.´lbf)
Reused bearing
0.5 - 1.0 N´m (5 - 10 kgf´cm, 4.3 - 8.7 in.´lbf)
If the preload is not within the specification, remove the trans-
mission case side outer race of the side bearing with SST (See
page MX-36).
(e) Select another shim.
HINT:
The preload will change by approx. 0.3 - 0.4 N´m (3 - 4 kgf´cm,
2.6 - 3.5 in.´lbf) corresponding to a change of 0.05 mm in shim
thickness.
MarkThickness mm (in.)MarkThickness mm (in.)
A2.10 (0.0827)L2.60 (0.1024)
B2.15 (0.0846)M2.65 (0.1043)
C2.20 (0.0866)N2.70 (0.1063)
D2.25 (0.0886)P2.75 (0.1083)
E2.30 (0.0906)Q2.80 (0.1102)
F2.35 (0.0925)R2.85 (0.1122)
G2.40 (0.0945)S2.90 (0.1142)
H2.45 (0.0965)T2.95 (0.1161)
J2.50 (0.0984)U3.00 (0.1181)
K2.55 (0.1004)--

V06938
ED
A
G
BC
F
H Code Shape Size
ù = 8
(0.31)
L = 15
(0.59)Code Shape Size Code Shape Size
ù = 5
(0.20)
L = 16
(0.63)
ù = 8
(0.31)ù = 5
(0.24)
L = 22
(0.87)
ù = 5
(0.20)
L = 14
(0.55)
ù = 6
(0.24)ù = 6
(0.24)
L = 20
(0.55)
ù = 5
(0.20)
L = 12
(0.47)mm (in.)
- BODYINSTRUMENT PANEL
BO-47
1141 Author
: Date
:
1996 TERCEL (RM440U)
HINT:
Screw shapes and sizes are indicated in the table below. The codes (A-H) correspond to those indicated
on the previous pages.