belt TOYOTA TERCEL 1996 Service User Guide

SS0M9-03
- SERVICE SPECIFICATIONSAIR CONDITIONING
SS-43
173 Author
: Date
:
1996 TERCEL (RM440U)
AIR CONDITIONING
SERVICE DATA
Refrigerant charge volume650 ± 50 g (22.93 ± 1.76 oz.)
Drive belt tension New belt
Used belt160 ± 25 lbf
100 ± 20 lbf
Idle-up speed850 ± 50 rpm
Magnetic clutch clearance0.5 ± 0.15 mm (0.02 ± 0.0059 in.)

EM0KA-05
P20168
EM-4
- ENGINE MECHANICALVALVE CLEARANCE
425 Author
: Date
:
1996 TERCEL (RM440U)
VALVE CLEARANCE
INSPECTION
HINT:
Inspect and adjust the valve clearance when the engine is cold.
1. DISCONNECT PCV HOSES FROM CYLINDER HEAD
COVER
2. REMOVE HIGH- TENSION CORDS AND IGNITION
COILS FROM SPARK PLUGS
3. REMOVE CYLINDER HEAD COVER
(a) Remove the oil filler cap.
(b) Remove the 5 cap nuts and seal washers.
(c) Pry out the cylinder head cover, and remove the cover
and gasket.
4. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with the
timing mark º0º of the No.1 timing belt cover.
(b) Check that the valve lifters on the No.1 cylinder are loose
and valve lifters on the No.4 cylinder are tight.
If not, turn the crankshaft 1 complete revolution (360°) and align
the marks as above.
5. INSPECT VALVE CLEARANCE
(a) Check only the valves indicated.
(1) Using a feeler gauge, measure the clearance be-
tween the valve lifter and camshaft.
(2) Record the out-of-specification valve clearance
measurements. They will be used later to determine
the required replacement adjusting shim.
Valve clearance (Cold):
Intake0.15 - 0.25 mm (0.006 - 0.010 in.)
Exhaust0.31 - 0.41 mm (0.012 - 0.016 in.)

P19787
SST(A)
SST(B)
Spark Plug Side
Z07669
B
A
BB
A
B
- ENGINE MECHANICALVALVE CLEARANCE
EM-5
426 Author
: Date
:
1996 TERCEL (RM440U)
(b) Turn the crankshaft pulley 1 revolution (360°) and align
its groove with the timing mark º0º of the No.1 timing belt
cover.
(c) Check only the valves indicated as shown. Measure the
valve clearance (See procedure in step (a)).
6. ADJUST VALVE CLEARANCE
(a) Remove the adjusting shim.
(1) Turn the crankshaft to position the cam lobe of the
camshaft on the adjusting valve points upward.
(2) Position the notch of the valve lifter so that the shim
can be removed with a small screwdriver as shown
in the illustration.
(3) Using SST (A), press down the valve lifter and place
SST (B) between the camshaft and valve lifter
flange. Remove SST (A).
SST 09248-55040 (09248-05410, 09248-05420)
HINT:

Apply SST (B) at slight angle on the side marked with º9º,
at the position shown in the illustration.

Set SST (A) at position A, if position A is too narrow, at
position B, as shown in the illustration.
(4) Remove the adjusting shim with a small screwdriver
and magnetic finger.

EM0K4-05
- ENGINE MECHANICALTIMING BELT
EM-1 1
432 Author
: Date
:
1996 TERCEL (RM440U)
TIMING BELT
COMPONENTS

EM1OD-01
P20154
Oil Pan
P20153
Ground Strap
P20536
Timing Mark
P20159
EM-12
- ENGINE MECHANICALTIMING BELT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE RH ENGINE UNDER COVER
2. w/ A/C and/or w/ PS:
REMOVE DRIVE BELT
3. REMOVE GENERATOR DRIVE BELT
4. SLIGHTY JACK UP ENGINE
5. SLIGHTLY JACK UP ENGINE
Raise the engine enough to remove the weight from the engine
mounting on the right side.
6. REMOVE RH ENGINE MOUNTING INSULATOR
(a) Remove the bolt and disconnect the ground strap.
(b) Remove the through bolt, 2 bolts, nut and mounting insu-
lator.
7. REMOVE NO.2 TIMING BELT COVER
Remove the 4 bolts, timing belt cover and gasket.
8. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with the
timing mark º0º of the No.1 timing belt cover.
NOTICE:
Always turn the crankshaft clockwise.
(b) Check that the hole of the camshaft timing pulley on the
side with the 5E mark is aligned with the timing mark of the
No.1 bearing cap.
If not, turn the crankshaft pulley 1 complete revolution (360°).
9. w/ A/C and/or w/ PS:
REMOVE NO.2 CRANKSHAFT PULLEY
Remove the 4 bolts and No.2 crankshaft pulley.

P20158
SST
P20155
SST
P20745
P20559
P20554
- ENGINE MECHANICALTIMING BELT
EM-13
1996 TERCEL (RM440U)
10. REMOVE CRANKSHAFT PULLEY
(a) Using SST, remove the pulley bolt.
SST 09213-14010, 09330-00021
(b) Using SST, remove the pulley.
SST 09950-50010 (09951-05010, 09952-05010,
09953-05020, 09954-05020)
11. REMOVE NO.3 TIMING BELT COVER
12. REMOVE NO.1 TIMING BELT COVER
Remove the 3 bolts, timing belt cover and gasket.
13. REMOVE TIMING BELT GUIDE
14. REMOVE TIMING BELT
HINT:
When re-using timing belt:
Draw a direction arrow on the timing belt (in direction of engine
revolution), and place matchmarks on the timing belt and pul-
leys as shown in the illustration.
(a) Remove the tension spring.

P20553
P20368
SST
P20741
EM-14
- ENGINE MECHANICALTIMING BELT
1996 TERCEL (RM440U)
(b) Loosen the No.1 idler pulley bolt and push it left as far as
it will go and then temporarily tighten it.
(c) Remove the timing belt.
15. REMOVE CAMSHAFT TIMING PULLEY
Using SST, remove the bolt and timing pulley.
SST 09960-10010 (09962-01000, 09963-01000)
16. REMOVE NO.1 IDLER PULLEY
17. REMOVE NO.2 IDLER PULLEY
18. REMOVE CRANKSHAFT TIMING PULLEY
If the timing pulley cannot be removed by hand, use a plastic-
faced hammer.
NOTICE:
Do not pry the rotor part of the pulley with the screwdriver.

EM0K6-01
EM0126
No!
P20576
EM3385
- ENGINE MECHANICALTIMING BELT
EM-15
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT TIMING BELT
NOTICE:

Do not bend, twist or turn the timing belt inside out.

Do not allow the timing belt to come into contact with
oil, water or steam.

Do not utilize timing belt tension when installing or re-
moving the mounting bolt of the camshaft timing
pulley.
If there are any defects as shown in the illustration, check these
points:
(a) Premature parting

Check for proper installation.

Check the timing cover gasket for damage and
proper installation.
(b) If the belt teeth are cracked or damaged, check to see if
either camshaft or oil pump is locked.
(c) If there is noticeable wear or cracks on the belt face,
check to see if there are nicks on the side of the idler
pulley lock.
(d) If there is wear or damage on only one side of the belt,
check the belt guide and the alignment of each pulley.
(e) If there is noticeable wear on the belt teeth, check the tim-
ing belt cover for damage and check gasket has been
installed correctly and for foreign material on the pulley
teeth.
If necessary, replace the timing belt.
2. INSPECT IDLER PULLEYS
(a) Visually check the seal portion of the idler pulley for oil
leakage.
If leakage is found, replace the idler pulley.
(b) Check that the idler pulley turns smoothly.
If necessary, replace the idler pulley.

P20528
38.4 mm EM-16
- ENGINE MECHANICALTIMING BELT
1996 TERCEL (RM440U)
3. INSPECT TENSION SPRING
(a) Measure the free length of tension spring.
Free length:
38.4 mm (1.512 in.)
If the free length is not as specified, replace the tension spring.
(b) Measure the tension of the tension spring at the specified
installed length.
Installed tension (at 47.4 mm (1.866 in.)):
32 N (3.3 kgf, 7.3 lbf)
If the installed tension is not as specified, replace the tension
spring.

EM1OE-01
P20743
P20742
P20744
P20390SST
P20915
Timing Mark
SST
Installation
Mark
- ENGINE MECHANICALTIMING BELT
EM-17
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL CRANKSHAFT TIMING PULLEY
(a) Align the pulley set key with the key groove of the pulley.
(b) Slide on the timing pulley, facing the rotor side of the
crankshaft position sensor inward.
2. TEMPORARILY INSTALL NO.1 IDLER PULLEY AND
TENSION SPRING
(a) Install the tension spring to the idler pulley.
(b) Align the bracket pin hole with the pivot pin.
(c) Install the idler pulley with the bolt. Do not tighten the bolt
yet.
(d) Pry the idler pulley toward the left as far as it will go and
temporarily tighten the bolt.
(e) Check that the idler pulley moves smoothly.
3. INSTALL NO.2 IDLER PULLEY
(a) Install the idler pulley with the bolt.
Torque: 28 N´m (280 kgf´cm, 20 ft´lbf)
(b) Check that the idler pulley moves smoothly.
4. INSTALL CAMSHAFT TIMING PULLEY
(a) Align the camshaft knock pin with the knock pin groove on
the pulley side with the 5E mark, and slide on the timing
pulley.
(b) Using SST, install the pulley bolt.
SST 09960-10010 (09962-01000, 09963-01000)
Torque: 51 N´m (510 kgf´cm, 37 ft´lbf)
5. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Using SST, align the hole of the camshaft timing pulley on
the side with the 5E mark with the timing mark of the bear-
ing cap.
SST 09960-10010 (09962-01000, 09963-01000)