egr TOYOTA TERCEL 1996 Service User Guide

A15708
- DIAGNOSTICSENGINE
DI-67
1996 TERCEL (RM440U)
TOYOTA hand-held tester:
1 Check connection of vacuum hose, EGR hose (See page EC-2).
NG Repair or replace.
OK
2 Check VSV for EGR.
PREPARATION:
Select the ACTIVE TEST mode on the TOYOTA hand-held tes-
ter.
CHECK:
Check operation of VSV, when it is operated by the TOYOTA
hand-held tester.
OK:
EGR system is OFF:
Air from pipe E is flowing out through the air filter.
EGR system is ON:
Air from pipe E is flowing out through pipe F.
OK Go to step 4.
NG
3 Check operation of VSV for EGR (See page EC-7).
NG Replace VSV for EGR.
OK
Check for open and short in harness and con-
nector between J/B No.2 and ECM
(See page IN-26).

DI-68
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
4 Check EGR vacuum modulator (See page EC-7).
NG Repair or replace.
OK
5 Check EGR valve (See page EC-7).
NG Repair or replace.
OK
6 Check manifold absolute pressure sensor (See page DI-23).
NG Repair or replace.
OK
Check and replace ECM (See page IN-26).
OBD II scan tool (excluding TOYOTA hand-held tester):
1 Check connection of vacuum hose, EGR hose (See page EC-2).
NG Repair or replace.
OK

A15709
- DIAGNOSTICSENGINE
DI-69
1996 TERCEL (RM440U)
2 Check VSV for EGR.
PREPARATION:
(a) Turn up the floor mat on the passenger side.
(b) Remove the 2 bolts for ECM.
(c) Disconnect the ºE5º or ºE8º connector of ECM.
(d) Turn the ignition switch ON.
CHECK:
Check VSV function
(1) Connect terminal EGR of the ECM connector and
the body ground (ON).
(2) Disconnect terminal EGR of the ECM connector
and the body ground (OFF).
OK:
(1) VSV is ON:
Air from pipe E is flowing out through pipe F.
(2) VSV is OFF:
Air from pipe E is flowing out through the air filter.
OK Go to step 4.
NG
3 Check operation of VSV for EGR (See page DI-65, step 3).
NG Replace VSV for EGR.
OK
Check for open and short in harness and
connector between J/B No.2 and ECM
(See page IN-26).
4 Check EGR vacuum modulator (See page EC-7).
NG Repair or replace.
OK

DI-70
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
5 Check EGR valve (See page EC-7).
NG Repair or replace.
OK
6 Check manifold absolute pressure sensor (See page DI-23).
NG Repair and replace.
OK
Check and replace ECM (See page IN-26).

- DIAGNOSTICSENGINE
DI-71
1996 TERCEL (RM440U)
DTC P0402 Exhaust Gas Recirculation Flow Excessive
Detected
CIRCUIT DESCRIPTION
Refer to DTC P0402 on page DI-65.
DTC No.DTC Detection ConditionTrouble Area
P0402
After the engine is warmed up, conditions (a) and (b) continue
(a) The intake manifold absolute pressure is larger than the
value calculated by the ECM while the EGR system is ON
(b) Misfiring is detected during idling
(2 trip detection logic)
EGR valve stuck open

Vacuum or EGR hose is connected to wrong post

Manifold absolute pressure sensor

ECM
INSPECTION PROCEDURE
HINT:

If DTC P0105 and/or P0106 and P0402 are output simultaneously, perform troubleshooting of DTC
P0105 first.

If DTC P0401 and P0402 are output simultaneously, perform troubleshooting of DTC P0402 first.
1 Check connection of vacuum hose, EGR hose (See page EC-2).
NG Repair or replace.
OK
2 Check EGR valve (See page EC-7).
NG Repair or replace.
OK
3 Check VSV for EGR (See page DI-65).
OK Go to step 5.
NG
DI95Q-01

DI-72
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
4 Check operation of the for EGR (See page EC-7).
NG Replace VSV for EGR.
OK
Check for open and short in harness and con-
nector between engine room R/B and ECM
(See page IN-26).
5 Check EGR vacuum modulator (See page EC-7).
NG Repair or replace.
OK
6 Check manifold absolute pressure sensor (See page DI-23).
NG Repair or replace.
OK
Check and replace ECM (See page IN-26).

EM18U-02
P19776
CO/HC Meter
- ENGINE MECHANICALCO/HC
EM-1
422 Author
: Date
:
1996 TERCEL (RM440U)
CO/HC
INSPECTION
HINT:
This check is used only to determine whether or not the idle CO/
HC complies with regulations.
1. INITIAL CONDITIONS
(a) Engine coolant at normal operating temperature.
(b) Air cleaner installed.
(c) All pipes and hoses of air induction system connected.
(d) All accessories switched OFF.
(e) All vacuum lines properly connected.
HINT:
All vacuum hoses for EGR systems, etc. should be properly
connected.
(f) SFI system wiring connectors fully plugged.
(g) Ignition timing set correctly.
(h) Transmission in neutral position.
(i) CO/HC meter calibrated by hand.
2. START ENGINE
3. RACE ENGINE AT 2,500 RPM FOR APPROX. 180 SE-
CONDS
4. INSERT CO/HC METER TESTING PROBE AT LEAST
40 cm (1.3 ft) INTO TAILPIPE DURING IDLING
5. IMMEDIATELY CHECK CO/HC CONCENTRATION AT
IDLE AND/OR 2,500 RPM
HINT:
When doing the 2 mode (2,500 rpm and idle) test, follow the
measurement order prescribed by the applicable local regula-
tions.

EM0494
P20156
SST(A)
SST(B)
EM-6
- ENGINE MECHANICALVALVE CLEARANCE
427 Author
: Date
:
1996 TERCEL (RM440U)
(b) Determine the replacement adjusting shim size by the fol-
lowing Formula or Charts on the next 2 pages:
(1) Using a micrometer, measure the thickness of the
removed shim.
(2) Calculate the thickness of a new shim so that the
valve clearance comes within specified value.
T ....... Thickness of removed shim
A ....... Measured valve clearance
N ....... Thickness of new shim
Intake:
N = T + (A - 0.20 mm (0.008 in.))
Exhaust:
N = T + (A - 0.36 mm (0.014 in.))
Select a new shim with a thickness as close as possible
to the calculated value.
HINT:
Shims are available in 17 increments of 0.05 mm (0.0020 in.),
from 2.50 mm (0.0984 in.) to 3.30 mm (0.1299 in.).
(c) Install a new adjusting shim.
(1) Place a new adjusting shim on the valve lifter.
(2) Using SST (A), press down the valve lifter and re-
move SST (B).
SST 09248-55040 (09248-05410, 09248-05020)
(d) Recheck the valve clearance.
7. REINSTALL CYLINDER HEAD COVER
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing:
Part No. 08826-00080 or equivalent
(b) Install the gasket to the cylinder head cover.
(c) Install the cylinder head cover with the 5 seal washers and
cap nuts.
Torque: 7.0 N´m (70 kgf´cm, 61 in.´lbf)
(d) Install oil filler cap.
8. REINSTALL IGNITION COILS AND HIGH-TENSION
CORDS
9. RECONNECT EGR VACUUM MODULATOR
10. RECONNECT PCV HOSES TO CYLINDER HEAD COV-
ER

EM18V-02
EM-10
- ENGINE MECHANICALIDLE SPEED
431 Author
: Date
:
1996 TERCEL (RM440U)
IDLE SPEED
INSPECTION
1. INITIAL CONDITIONS
(a) Engine coolant at normal operating temperature.
(b) Air cleaner installed.
(c) All pipes and hoses of air induction system connected.
(d) All accessories switched OFF.
(e) All vacuum lines properly connected.
HINT:
All vacuum hoses for EGR system, etc. should be properly connected.
(f) SFI system wiring connectors fully plugged.
(g) Ignition timing set correctly.
(h) Transmission in neutral position.
2. CONNECT TOYOTA HAND-HELD TESTER OR OBDII SCAN TOOL (See page EM-9)
3. INSPECT IDLE SPEED
(a) Race the engine speed at 2,500 rpm for approx. 90 seconds.
(b) Check the idle speed.
Idle speed:
750 ± 50 rpm
(w/ Cooling fan OFF and transmission in neutral position)
If the idle speed is not as specified, check the IAC valve and air intake system.
4. DISCONNECT TOYOTA HAND-HELD TESTER OR OBDII SCAN TOOL

EG0023
EM-24
- ENGINE MECHANICALCYLINDER HEAD
1996 TERCEL (RM440U)
9. w/ A/C and w/o PS:
REMOVE IDLER PULLEY BRACKET
(a) Loosen the idler pulley mounting nut and adjusting bolt,
and remove the drive belt.
(b) Remove the 3 bolts and idler pulley bracket.
10. REMOVE IGNITION COILS AND SPARK PLUGS
11. DISCONNECT VACUUM HASES
(a) Disconnect the vacuum hose from the EGR valve.
(b) Disconnect the 3 vacuum hoses from the throttle body.
(c) Disconnect the vacuum hose from the TVV (to charcoal
canister).
(d) Disconnect the vacuum hose from the TVV (to throttle
body).
(e) Disconnect the vacuum hose from the EGR VSV.
12. REMOVE THROTTLE BODY (See page MF-28)
13. REMOVE EGR PIIPE
Loosen the union nut, and remove the 2 nuts, EGR pipe and
gasket.
14. REMOVE EGR VALVE AND VACUUM MODULATOR
(a) Remove the bolt and disconnect the vacuum modulator.
(b) Remove the 2 nuts, EGR valve, EGR vacuum modulator
with the bracket and gasket.
15. REMOVE EGR VSV AND CAMSHAFT POSITION SEN-
SOR
(a) Disconnect the EGR VSV and camshaft position sensor
connector.
(b) Remove the bbolt and EGR VSV.
(c) Remove the bolt, camshaft position sensor and O-ring.