instrument panel TOYOTA TERCEL 1996 Service User Guide

A15689
FI7052
DI-34
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTC P0105, P0110, P0120 are output simultaneously, E2 (sensor ground) may be open.
1 Connect OBD II scan tool or TOYOTA hand-held tester and read throttle valve
opening percentage.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tes-
ter to the DLC3.
(c) Turn the ignition switch ON and OBD II scan tool or TOY-
OTA hand-held tester main switch ON.
CHECK:
Read the throttle valve opening percentage.
OK:
Throttle valveThrottle valve opening
position expressed as percentage
Fully openApprox. 70 %
Fully closedApprox. 10 %
OK Check for intermittent problems
(See page DI-3).
NG

A15693
- DIAGNOSTICSENGINE
DI-39
1996 TERCEL (RM440U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Connect OBD II scan tool or TOYOTA hand-held tester and read value for volt-
age output of heated oxygen sensor.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up the engine to the normal operating temperature.
CHECK:
Read the voltage output of the heated oxygen sensor (bank 1 sensor 1) when the engine is suddenly raced.
HINT:
Perform quick racing to 4,000 rpm 3 times using accelerator pedal.
OK:
Heated oxygen sensor output a RICH signal (0.45 V or more) at least once.
OK Check and replace ECM (See page IN-26).
NG
2 Check for open and short in harness and connector between ECM and oxygen
sensor (See page IN-26).
NG Repair or replace harness or connector.

DI-42
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check for open and short in harness and connector between ECM and oxygen
sensor (See page IN-26).
NG Repair or replace harness or connector.
OK
2 Check for oxygen sensor data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up engine to normal operating temperature.
CHECK:
Read the oxygen sensor output voltage and short-term fuel trim.
RESULT:
PatternOxygen sensor output voltageShort-term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about +20 %
2Rich condition (Changes at 0.4 V or more)Changes at about -20 %
3Except 1 and 2
1, 2 Check fuel trim system (See page DI-49).
3

DI-46
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
3 Check output voltage of heated oxygen sensor (bank 1 sensor 2).
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) After warming up the engine, race the engine at 2,500 rpm for 3 minutes.
CHECK:
Read the output voltage of the heated oxygen sensor (bank 1 sensor 2) when racing the engine after 3 min-
utes have elapsed.
OK:
Heated oxygen sensor output voltage: Alternates from 0.4 V or less to 0.5 V or more.
OK Check that each connector is properly
connected.
NG
Replace heated oxygen sensor.

DI-50
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check air induction system (See page MF-1).
NG Repair or replace.
OK
2 Check for heated oxygen sensor data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up engine to normal operating temperature.
CHECK:
Read the oxygen sensor output voltage and short-term fuel trim.
RESULT:
PatternOxygen sensor output voltageShort-term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about + 20 %
2RIch condition (Changes at 0.4 V or more)Changes at about - 20 %
3Except 1 and 2
3 Check for oxygen sensor
(See page DI-41).
1, 2
3 Check fuel pressure (See page MF-1).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter. (See page MF-5)
OK

A15740
DI-106
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
A/C Cut Control Circuit
CIRCUIT DESCRIPTION
This circuit cuts air conditioning operation during vehicle acceleration in order to increase acceleration per-
formance. During acceleration with the vehicle speed at 25 km/h (16 mph) or less, engine speed at 1,200
rpm or less and throttle valve opening angle at 50° or more, the A/C magnet switch is turned OFF for several
seconds.
WIRING DIAGRAM
INSPECTION PROCEDURE
TOYOTA hand-held tester:
1 Connect TOYOTA hand-held tester and check operation of air conditioning cut
control.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand-held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand-held tester main switch ON.
(d) Start the engine and air conditioning switch ON.
HINT:
A/C magnet clutch is turned ON.
(e) Select the ACTIVE TEST mode on the TOYOTA hand-held tester.
CHECK:
Check operation of A/C magnet clutch cut when air conditioning cut control is operated by the TOYOTA
hand-held tester.
OK:
A/C magnet clutch is turned OFF
OK Proceed to next circuit inspection shown on
matrix chart (See page DI-19).
DI1EK-09

DI4M8-01
N12263
Front Passenger
Airbag Assembly Steering Wheel Pad
(With Airbag)
Spiral Cable
Airbag Sensor Assembly
Instrument Panel
Junction BlockSRS Warning Light
DI-152
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TERCEL (RM440U)
PARTS LOCATION

DI4MR-02
N20816
BatteryEngine Room
Relay BlockInstrument Panel
Junction BlockTheft Deterrent ECU
+B1
T41
1D8
1K11
L-Y L-Y
2
MAIN FL
EA2BDOME 1
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
DI-197
1996 TERCEL (RM440U)
CIRCUIT INSPECTION
ECU Power Source Circuit (w / Theft deterrent System)
CIRCUIT DESCRIPTION
This circuit provides power to operate the theft deterrent and door lock ECU.
WIRING DIAGRAM

N20817
BatteryInstrument Panel
Junction BlockTheft Deterrent ECU
(Door Lock Control Relay)
1J2
W-G
MAIN FLEA2
F7 F6 221A3
D6 (8)
T39
D6 (16)
T34
A A
IEJ3
JUNCTION
CONNECTOR A
AW-B
ALT AM1POWER
2 1L
W-B B W-G
( ): w/o Theft Deterrent System+B2
(B)
E
B-R B-R2JUNCTION
CONNECTOR J6
J/B No.2
11J/B No.7 DI-200
- DIAGNOSTICSPOWER DOOR LOCK CONTROL SYSTEM
1996 TERCEL (RM440U)
Actuator Power Source Circuit
CIRCUIT DESCRIPTION
This circuit provides power to drive the door lock motor.
WIRING DIAGRAM
DI4MS-01

N20822
Battery MAIN FL 1
F6 F7ALT B-R
Taillight
LH Taillight
RH 2
EA2B-R
G 1J1Instrument Panel Junction Block
Taillight Control Relay
TAIL4
1E
8
1L
G G LGTheft Deterrent ECU
23
T4 TAIL
1
B
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
DI-235
1996 TERCEL (RM440U)
Taillight Control Relay Circuit
CIRCUIT DESCRIPTION
When the theft deterrent system is activated, it causes the Tr in the ECU to switch on and off at approximately
0.4 sec. intervals. This switches the taillight control relay on and off, thus flashing the taillights (See the wiring
diagram below).
In this condition, if any of the following operations is done, the Tr in the ECU goes off and the taillight control
relay switches off, thus stopping the taillights flashing:
(1) Unlock the front LH or RH door with key.
(2) Turn the ignition switch to ACC or ON position.
(3) Unlock the doors with the wireless door lock control system.
(4) Wait for approximately 60 seconds.
WIRING DIAGRAM
DI4N9-01