wheel alignment TOYOTA TERCEL 1996 Service User Guide

SA12B-02
- SUSPENSION AND AXLEFRONT DRIVE SHAFT
SA-23
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page SA-18).
HINT:
After installation, check ABS speed sensor signal and front wheel alignment (See page DI-1 11 and
SA-4).

SA11F-02
SA-30
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page SA-25).
HINT:
After installation, check front wheel alignment (See page SA-2).

SA11I-02
- SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
SA-33
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page SA-32).
HINT:
After installation, check front wheel alignment (See page SA-4).

SR05N-06
SR-2
- STEERINGTROUBLESHOOTING
922 Author
: Date
:
1996 TERCEL (RM440U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in the order shown. If necessary, repair or replace these parts.
SymptomSuspect AreaSee page
Hard steering
1. Tires (Improperly inflated)
2. Power steering fluid level (Low)
3. Drive belt (Loose)
4. Front wheel alignment (Incorrect)
5. Steering system joints (Worn)
6. Suspension arm ball joints (Worn)
7. Steering column (Binding)
8. Power steering gearSA-2
SR-6
SR-3
SA-4
-
SA-36
-
SR-46
Poor return
1. Tires (Improperly inflated)
2. Front wheel alignment (Incorrect)
3. Steering column (Binding)
4. Power steering gearSA-2
SA-4
-
SR-46
Excessive play
1. Steering system joints (Worn)
2. Suspension arm ball joints (Worn)
3. Intermediate shaft, Sliding yoke (Worn)
4. Front wheel bearing (Worn)
5. Power steering gear-
SA-36
-
SA-10
SR-46
Abnormal noise
1. Power steering fluid level (Low)
2. Steering system joints (Worn)
3. Power steering gearSR-6
-
SR-46

SR0KW-02
- STEERINGMANUAL STEERING GEAR
SR-45
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL MANUAL STEERING GEAR ASSEMBLY
Install the gear assembly from the LH of the vehicle.
2. INSTALL 2 GROMMETS AND BRACKETS
Torque the 2 bolts and nuts.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
3. CONNECT SLIDING YOKE (See page SR-20)
4. INSTALL COLUMN HOLE COVER
Torque the 4 nuts.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
5. CONNECT RH AND LH TIE ROD ENDS (See page SA-10)
6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
HINT:
Do it with the front of the vehicle jacked up.
7. w/ Airbag:
CENTER SPIRAL CABLE (See page SR-20)
8. INSTALL STEERING WHEEL
(a) Install the wheel at straight-ahead position.
(b) Temporarily tighten the wheel set nut.
(c) Connect the connector.
9. CHECK STEERING WHEEL CENTER POINT
10. w/ Airbag:
TORQUE STEERING WHEEL SET NUT
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
11. w/ Airbag:
INSTALL STEERING WHEEL PAD (See page SR-20)
12. CHECK FRONT WHEEL ALIGNMENT (See page SA-4)

- STEERINGPOWER STEERING GEAR
SR-63
1996 TERCEL (RM440U)
9. INSTALL FRONT EXHAUST PIPE
(a) Connect the 2 rings.
(b) Install the bolt and clamp over a new gasket.
Torque: 19 N´m (190 kgf´cm, 14 ft´lbf)
(c) Install the 2 bolts and compression springs over a new
gasket.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
10. INSTALL OXYGEN SENSOR
Install the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
11. CONNECT SLIDING YOKE (See page SR-20)
12. INSTALL COLUMN HOLE COVER
Torque the 2 bolts and nut.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
13. CONNECT RH AND LH TIE ROD ENDS
(See page SA-10)
14. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
HINT:
Do it with the front of the vehicle jacked up.
15. w/ Airbag:
CENTER SPIRAL CABLE (See page SR-20)
16. w/ Airbag:
INSTALL STEERING WHEEL
(a) Install the wheel at straight-ahead position.
(b) Temporarily tighten the wheel set nut.
(c) Connect the connector.
17. BLEED POWER STEERING SYSTEM
(See page SR-5)
18. CHECK STEERING WHEEL CENTER POINT
19. w/ Airbag:
TORQUE STEERING WHEEL SET NUT
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
20. w/ Airbag:
INSTALL STEERING WHEEL PAD (See page SR-20)
21. CHECK FRONT WHEEL ALIGNMENT
(See page SA-4)