Timing TOYOTA TERCEL 1996 Service Owner's Guide

EG0010
Timing Mark
P20369
Timing Mark
EXIN
Other Timing Mark
P20377
8
6
13 4
2
57
P20248
Seal Packing EM-46
- ENGINE MECHANICALCYLINDER HEAD
1996 TERCEL (RM440U)
(e) Apply engine oil to thrust portion of the exhaust camshaft.
(f) Engage the exhaust camshaft gear to the intake cam-
shaft gear by matching the timing marks on each gear.
NOTICE:
There are also assembly reference marks on each gear as
shown in the illustration. Do not use these marks.
(g) Roll down the exhaust camshaft onto the bearing journals
while engaging gears with each other.
HINT:
The above angle allows the No.2 and No.4 cylinder cam lobes
of the exhaust camshaft to push their valve lifters evenly.
(h) Lightly push the exhaust camshaft gear without applying
excessive force.
(i) Install the 4 bearing caps in their proper locations.
(j) Temporarily tighten the bearing cap bolts uniformly and
alternately, in several passes, in the sequence shown un-
til the bearing caps are snug with the cylinder head.
(k) Remove the service bolt.
(l) Clean the installed surfaces of the No.2 bearing cap and
cylinder head with cleaner.
(m) Apply seal packing to the No.2 bearing cap as shown.
Seal packing:
Part No. 08826-00080 or equivalent

P20410
P20366
8
6
13 4
2
57
9 10
P20369
Timing Mark
EXIN
Other Timing Mark
P20557
P20363
EM-48
- ENGINE MECHANICALCYLINDER HEAD
1996 TERCEL (RM440U)
(v) Place the No.1 bearing cap in its proper location. When
doing this, check that there is no gap between the cylinder
head and the contact surface of bearing cap.
(w) Temporarily tighten the bearing cap bolts, alternately
tightening the left and right bolts uniformly.
(x) Install and uniformly tighten the 10 bearing cap bolts, in
several passes, in the sequence shown.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)
(y) Turn the camshaft 1 revolution and check that the timing
marks of the camshaft gears are aligned.
5. CHECK AND ADJUST VALVE CLEARANCE (See page
EM-4)
6. INSTALL CAMSHAFT TIMING PULLEY
(a) Align the camshaft knock pin with the knock pin groove on
the pulley side with the 5E mark, and slide the pulley.
(b) Secure the hexagonal portion of the camshaft, and install
and torque the bolt.
Torque: 51 N´m (510 kgf´cm, 37 ft´lbf)
7. INSTALL NO.2 IDLER PULLEY
Install the idler pulley with the bolt. Torque the bolt.
Torque: 28 N´m (280 kgf´cm, 20 ft´lbf)
HINT:
Remove any oil or water on the idler pulley and keep it clean.

P20948
P20953
Timing Mark
Installation
Mark
P20746
P20748
P20749
- ENGINE MECHANICALCYLINDER HEAD
EM-49
1996 TERCEL (RM440U)
8. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with timing
mark º0º of the No.1 timing belt cover.
(b) Turn the camshaft, and align the hole of the camshaft tim-
ing pulley on the side with the 5E mark with the timing
mark of the bearing cap.
9. INSTALL TIMING BELT
(a) Starting from the right hand side of the pulley and instal-
ling the belt counterclockwise.
(b) Loosen the No.1 idler pulley mounting bolt until the pulley
is moved slightly by the spring tension.
(c) Turn the crankshaft pulley 2 revolutions from TDC to TDC.
NOTICE:
Always turn the crankshaft clockwise.

P20538
Timing Mark
Installation Mark
P20361
P20286
Seal Packing
P20406
EM-50
- ENGINE MECHANICALCYLINDER HEAD
1996 TERCEL (RM440U)
(d) Check that each pulley aligns with the timing marks as
shown in the illustration.
If the timing marks do not align, remove the timing belt and rein-
stall it.
(e) Tighten the mounting bolt of the No.1 idler pulley.
Torque: 18.5 N´m (185 kgf´cm, 13 ft´lbf)
10. INSTALL NO.3 TIMING BELT COVER
11. INSTALL GENERATOR DRIVE BELT (See page
CH-2)
12. INSTALL NO.2 TIMING BELT COVER
(a) Install the gasket to the belt cover.
(b) Install the belt cover with the 4 bolts.
13. INSTALL CHARCOAL CANISTER (See page EM-17)
14. INSTALL CYLINDER HEAD COVER
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing:
Part No. 08826-00080 or equivalent
(b) Install the gasket to the cylinder head cover.
(c) Install the cylinder head cover with the 5 seal washers and
nuts.
Torque: 7.0 N´m (70 kgf´cm, 61 in.´lbf)
(d) Install the oil filler cap.
15. INSTALL INTAKE MANIFOLD
(a) Install air pipe a new gasket and the intake manifold with
the 2 bolts and 3 nuts.
Torque: 19.5 N´m (195 kgf´cm, 14 ft´lbf)

EM0JQ-06
EM9411
EM9412
P20480
SST
P20478
SST
P20477
12 mm
Hexagon
Wrench EM-70
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
DISASSEMBLY
1. M/T:
REMOVE CLUTCH COVER AND DISC
2. REMOVE FLYWHEEL (M/T) OR DRIVE PLATE (A/T)
3. REMOVE REAR END PLATE
4. INSTALL ENGINE TO ENGINE STAND FOR DIS-
ASSEMBLY
5. REMOVE TIMING BELT AND PULLEYS
6. REMOVE CYLINDER HEAD
7. REMOVE OIL DIPSTICK GUIDE AND GENERATOR
ADJUSTING BAR
8. REMOVE WATER PUMP WITH WATER INLET PIPE
9. REMOVE GENERATOR BRACKET
10. REMOVE KNOCK SENSOR
Using SST, remove the knock sensor.
SST 09816-30010
11. REMOVE RH ENGINE MOUNTING BRACKET
12. REMOVE OIL FILTER
13. REMOVE OIL PRESSURE SWITCH
Using SST, remove the oil pressure switch.
SST 09816-30010
14. REMOVE OIL PUMP AND PRESSURE REGULATOR
VA LV E
15. REMOVE OIL FILTER UNION
Using a 12 mm hexagon wrench, remove the oil filter union.

P20750
P20480
SST
P20545
EM9412
EM7333
EM-90
- ENGINE MECHANICALCYLINDER BLOCK
1996 TERCEL (RM440U)
15. INSTALL RH ENGINE MOUNTING BRACKET
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
16. INSTALL KNOCK SENSOR
Using SST, install the knock sensor.
SST 09816-30010
Torque: 45 N´m (450 kgf´cm, 33 ft´lbf)
17. INSTALL GENERATOR BRACKET
Torque: 24 N´m (240 kgf´cm, 18 ft´lbf)
18. INSTALL WATER PUMP WITH WATER INLET PIPE
19. INSTALL OIL DIPSTICK GUIDE AND GENERATOR AD-
JUSTING BAR
20. INSTALL CYLINDER HEAD
21. INSTALL TIMING BELT AND PULLEYS
22. REMOVE ENGINE STAND
23. INSTALL REAR END PLATE
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
24. M/T:
INSTALL FLYWHEEL
(a) Apply adhesive to 2 or 3 threads of new mounting bolt
end.
Adhesive:
Part No. 08833-00070, THREE BOND 1324 or
equivalent

LU08D-05
P20907
EM9278
EM9755
P20160
- LUBRICATIONOIL PUMP
LU-7
1996 TERCEL (RM440U)
REMOVAL
HINT:
When repairing the oil pump, the oil pan and strainer should be
removed and cleaned.
1. REMOVE HOOD
2. REMOVE OIL DIPSTICK
3. DRAIN ENGINE OIL
4. REMOVE TIMING BELT (See page EM-12)
5. SUSPEND ENGINE WITH ENGINE SLING DEVICE
6. REMOVE CRANKSHAFT TIMING PULLEY(See page
EM-12)
7. w/ A/C:
REMOVE A/C COMPRESSOR AND MOUNTING
BRACKET
(a) Disconnect the compressor connector.
(b) Remove the 4 compressor mounting bolts.
HINT:
Put a side compressor, and suspend it.
(c) Remove the 4 bolts and compressor mounting
bracket.
8. DISCONNECT FRONT EXHAUST PIPE
(a) Remove the 2 bolts and the 2 compresson springs.
(b) Disconnect the exhaust pipe.

LU-16
- LUBRICATIONOIL PUMP
1996 TERCEL (RM440U)
(a) Place a new gasket on the exhaust pipe.
(b) Connect the exhaust pipe to the exhaust manifold with 2
compresson springs and 2 bolts.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
6. w/ A/C:
INSTALL A/C COMPRESSOR AND MOUNTING
BRACKET
(a) Install the compressor mounting bracket with the 4 bolts.
Torque: 27 N´m (270 kgf´cm, 20 ft´lbf)
(b) Install the A/C compressor to the bracket with the 4 bolts.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
(c) Connect the A/C compressor connector.
7. INSTALL CRANKSHAFT TIMING PULLEY (See page
EM-17)
8. INSTALL TIMING BELT (See page EM-17)
9. INSTALL OIL DIPSTICK
10. FILL WITH ENGINE OIL
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK ENGINE OIL LEVEL
13. INSTALL HOOD

IG08M-04
P21254
Connector Clamp
P21034
- IGNITIONCRANKSHAFT POSITION SENSOR
IG-13
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT CRANKSHAFT POSITION SENSOR
CONNECTOR AND CLAMP
2. REMOVE RH ENGINE UNDER COVER
3. REMOVE NO.2 TIMING BELT COVER (See page
EM-12)
4. REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and disconnect the crankshaft position sensor.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)