drain TOYOTA TERCEL 1996 Service Owner's Guide

AT3320
AX0RX-01
Q06911
Z15036
20 (0.79)
12 (0.47)25 (0.98)
20 (0.79)
AT3329
AX-16
- AUTOMATIC TRANSAXLE (A242L)VALVE BODY ASSEMBLY
798 Author
: Date
:
1996 TERCEL (RM440U)
VALVE BODY ASSEMBLY
ON-VEHICLE REPAIR
1. DRAIN ATF
Remove the drain plug and drain the ATF into the suitable con-
tainer.
Torque: 17 N´m (175 kgf´cm, 13 ft´lbf)
2. REMOVE OIL PAN AND GASKET
NOTICE:
Some fluid will remain in the oil pan. Remove the oil pan
bolts and carefully remove the oil pan assembly. Discard
the gasket.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
3. EXAMINE PARTICLES IN PAN
Remove the magnets and use then to collect any steel chips.
Look at the chips on the magnet carefully to anticipate what
type of wear you will find in the transaxle.
Steel (magnetic) ...... bearing, gear and plate wear
Brass (non-magnetic) ..... bushing wear
4. REMOVE OIL STRAINER AND APPLY PIPE BRACKET
(a) Remove the 3 bolts and oil strainer.
NOTICE:
Be careful as some oil will come out of the strainer.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
(b) Remove the 2 bolts and apply pipe bracket.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
5. REMOVE OIL PIPES
(a) Remove the clamp bolt.
(b) Pry up the both pipe ends with a large screwdriver and re-
move the 4 pipes.
NOTICE:
Be careful not to bend or damage the pipes.

AX0S3-01
Q02133
SST
- AUTOMATIC TRANSAXLE (A242L)DIFFERENTIAL OIL SEAL
AX-23
805 Author
: Date
:
1996 TERCEL (RM440U)
DIFFERENTIAL OIL SEAL
ON-VEHICLE REPAIR
1. DRAIN TRANSAXLE FLUID
2. REMOVE ENGINE UNDER COVER
3. REMOVE LH AND RH DRIVE SHAFTS
(See page SA-18)
4. REMOVE SIDE OIL SEAL
Using SST, drive out the oil seals on both sides.
SST 09308-00010

SA128-02
FA1535
SST
F03986
SA-18
- SUSPENSION AND AXLEFRONT DRIVE SHAFT
1996 TERCEL (RM440U)
REMOVAL
NOTICE:

The hub bearing could be damaged if it is subjected
to the vehicle weight, such as when moving the ve-
hicle with the drive shaft removed. Therefore, if it is
absolutely necessary to place the vehicle weight on
the hub bearing, first support it with SST.
SST 09608-16042 (09608-02021, 09608-02041)

w/ ABS:
After disconnecting the drive shaft from the axle hub,
work carefully so as not to damage the sensor rotor
serrations on the drive shaft.
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. M/T:
REMOVE LH ENGINE UNDER COVER
3. DRAIN TRANSAXLE OIL (M/T) OR ATF (A/T)
4. w/ ABS:
REMOVE BOLT AND ABS SPEED SENSOR
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
5. REMOVE DRIVE SHAFT LOCK NUT
(a) Remove the cotter pin and lock cap.
(b) While applying the brakes, remove the nut.
Torque: 216 N´m (2,200 kgf´cm, 159 ft´lbf)
6. DISCONNECT TIE ROD END FROM STEERING
KNUCKLE (See page SA-10)
7. DISCONNECT LOWER BALL JOINT FROM LOWER
SUSPENSION ARM (See page SA-10)
8. DISCONNECT DRIVE SHAFT FROM AXLE HUB
NOTICE:
Be careful not to damage the drive shaft boot and inner oil
seal.

BR0RQ-05
BR4220
BR-24
- BRAKEFRONT BRAKE CALIPER
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
Install the flexible hose lock securely in the lock hole in the cali-
per.
(b) Use a container to catch the brake fluid as it drains out.
2. REMOVE CALIPER
Remove the 2 installation bolts, and caliper.
Torque: 25 N´m (255 kgf´cm, 18 ft´lbf)
3. REMOVE THESE PARTS:
(a) 2 brake pads with anti-squeal shims.
(b) 4 pad support plates.

N14519
Drain Hose
- AIR CONDITIONINGAIR CONDITIONING SYSTEM
AC-9
1996 TERCEL (RM440U)
3. INSPECT IDLE-UP SPEED
(a) Warm up engine.
(b) Inspect idle-up speed when the these conditions are es-
tablished.
Test conditions:
Blower speed control switch HI
Electrical lood OFF
A/C switch ON
Put gear shift in neutral
Standard idle-up speed: 800 - 900 rpm
If idle speed is not as specified, check the IAC valve and air in-
take system.
4. INSPECT FOR LEAKAGE OF REFRIGERANT
(a) Perform in these conditions:
Stop engine.
Secure good ventilation (If the gas leak detector
may not react to volatile gases which are not refrig-
erant, such as evaporated gasoline and exhaust
gas.)
Repeat the test 2 or 3 times.
Make sure that there is some refrigerant remaining
in the refrigeration system.
When compressor is OFF: approx. 392 - 588 kPa
(4 - 6 kgf/ cm
2, 57 - 85 psi)
(b) Bring the gas leak detector close to the drain hose before
performing the test.
HINT:
After the blower motor has stopped, leave the cooling unit
for more than 15 minutes.
Expose the gas leak detector sensor under the drain
hose.
When bring the gas leak detector close to the drain hose,
make sure that the gas leak detector does not react to the
volatile gases.
If such reaction is unavoidable, the vehicle must be lifted up.
(c) If gas leak is not detected on the drain hose, remove the
power transistor from the cooling unit. Then insert the gas
leak detector sensor into the unit and perform the test.
(d) Disconnect the connector and leave the pressure switch
for approx. 20 minutes. Then bring the gas leak detector
close to the pressure switch and perform the test.
(e) Bring the gas leak detector close to the refrigerant lines
and perform the test.

AC1CG-04
AC2884
Hose Clip
Heater Radiator
Pipe
Water Hose
InsulatorLeft Side
of Vehicle
N12242
AC-32
- AIR CONDITIONINGHEATER UNIT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE COOLING UNIT
(See page AC-27)
2. DRAIN ENGINE COOLANT FROM RADIATOR
HINT:
It is not necessary to drain out all the coolant.
3. DISCONNECT WATER HOSES FROM HEATER RA-
DIATOR PIPES
HINT:

Push the water hose onto the heater radiator pipe as far
as the ridge on the pipe.

Install the hose clip in a position, as shown in the illustra-
tion.
4. REMOVE PIPE GROMMETS
5. REMOVE INSTRUMENT PANEL SAFETY PAD AND
REINFORCEMENT (See page BO-48)
6. REMOVE HEATER UNIT
Remove the 2 nuts and the heater unit.
7. REMOVE HEATER RADIATOR
(a) Remove the screw and clamp.
(b) Pull out the heater radiator.