Egr TOYOTA TERCEL 1996 Service Service Manual

N12798
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-19
1996 TERCEL (RM440U)
(e) Connect the positive (+) lead from the battery to terminal
9.
(f) Check that the chime stops sounding.
HINT:
Check the chime within a period of 4 to 8 seconds.
If operation is not as specified, replace the relay.
10. INSPECT INTEGRATION RELAY CIRCUIT
(See page BE-1 1)

BE0RA-02
I05953
Combination Meter

Meter CircuitDoor Lock Control Relay or Theft Deterrent ECU
ECM
Ignition Switch Rheostat Light Control Volume
ABS ECUBrake Fluid Level Warning Switch
Engine Room R/B

DOME Fuse
I/P J/B

Integration Relay

GAUGE Fuse

IGN Fuse

TURN Fuse

TAIL FuseAirbag Sensor Assembly
Parking Brake Switch
- BODY ELECTRICALCOMBINATION METER
BE-33
1996 TERCEL (RM440U)
LOCATION

N12807
N12808
BE1348
OFFBright
(0 W)
Dark
(10 W)
- BODY ELECTRICALCOMBINATION METER
BE-43
1996 TERCEL (RM440U)
18. INSPECT INTEGRATION RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminals
3 and 9.
(b) Connect the terminal 2 to terminal 9 through the 3.4 W test
bulb.
(c) Connect the negative (-) lead from the battery to terminal
7.
(d) Check that the bulb lights and the chime sounds for 4 -
8 seconds.
(e) Return to step (a), and operate the chime again.
(f) Connect the negative (-) lead from the battery to terminal
3.
(g) Check that the chime stops sounding.
HINT:
Check the chime within a period of 4 to 8 seconds.
If operation is not as specified, replace the relay.
19. INSPECT INTEGRATION RELAY CIRCUIT
(See page BE-1 1)
20. INSPECT LIGHT CONTROL RHEOSTAT
(a) Turn the rheostat knob OFF, and check that there is no
continuity between terminals.(Rheostat knob turned to
fully counterclockwise.)
(b) Gradually, turn the rheostat knob from the dark side to
bright side, and check that the resistance decreases from
10 to 0 W .(Rheostat knob turned to clockwise.)
If operation is not as specified, replace the rheostat.

N15573
4-Door:
Door Glass RunFront Door Belt Moulding
Outside Handle Door Lock Cylinder
Door Glass
Rear View Mirror
Inner Cover
Door Hinge Control Link Door Lock
Front Lower
Frame
Service Hole Cover
Window Regulator
Inside Handle
Snap Ring Armrest Door Trim
Armrest Cover w/ Power Window:
w/ Power Window: w/ Power Door Lock:
Speaker
Plate Door Trim

Precoated partRegulator HandleGrommetDoor Hinge Door Checker Door Lock
Window Regulator

Armrest Panel
BO-10
- BODYFRONT DOOR
1104 Author
: Date
:
1996 TERCEL (RM440U)

BO34E-01
BO0632
BO0633
15°
45°
- BODYSEAT BELT
BO-57
1996 TERCEL (RM440U)
INSPECTION
CAUTION:
Replace the seat belt assembly (outer belt, inner belt, bolts
or nuts and sill-bar) if it has been used in a severe impact.
The entire assembly should be replaced even if damage is
not obvious.
Emergency Locking Retractor (ELR) and Automatic Lock-
ing Retractor (ALR) type
1. All seat belt:
RUNNING TEST (IN SAFE AREA)
(a) Fasten the front seat belts.
(b) Drive the car at 10 mph (16 km/h) and make a very hard
stop.
(c) Check that the belt is locked and cannot be extended at
this time.
HINT:
Conduct this test in a safe area. If the belt does not lock, remove
the belt mechanism assembly and conduct the following static
check. Also, whenever installing a new belt assembly, verify the
proper operation before installation.
2. Driver 's seat belt (ELR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
(c) Tilt the retractor slowly.
(d) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out at over 45 degrees
of tilt.
If a problem is found, replace the assembly.
3. Except driver's seat belt (ALR/ ELR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
(c) Pull out the whole belt and measure the length of the
whole belt. Then retract the belt slightly and pull it out
again.
(d) Make sure that the belt cannot be extended further.
If a problem is found, replace the assembly.