Block TOYOTA TERCEL 1996 Service Manual Online

BR0RF-06
BR5036
Soft Jaws
BR5037
Soft Jaws
R12236
A
- BRAKEBRAKE MASTER CYLINDER
BR-1 1
1996 TERCEL (RM440U)
DISASSEMBLY
1. REMOVE RESERVOIR
(a) Remove the set screw and pull out the reservoir.
Torque: 1.7 N´m (17.5 kgf´cm, 15.2 in.´lbf)
(b) Remove the cap and strainer from the reservoir.
2. REMOVE 2 GROMMETS
3. PLACE CYLINDER IN VISE
4. REMOVE PISTON STOPPER BOLT
Using a screwdriver, push the pistons in all the way and remove
the piston stopper bolt and gasket.
HINT:
Tape the screwdriver tip before use.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
5. REMOVE PISTONS
(a) Push in the piston with a screwdriver and remove the
snap ring with snap ring pliers.
(b) Remove the No.1 piston and spring by hand, pulling
straight out, not at an angle.
NOTICE:

If pulled out and installed at an angle, there is a possi-
bility that the cylinder bore could be damaged.

Be careful not to damage the rubber lips on the pis-
tons.
(c) Place a rag and 2 wooden blocks on the work table and
lightly tap the cylinder flange against the block edges until
the No.2 piston drops out of the cylinder.
HINT:
Make sure the distance (A) from the rag to the top of the blocks
is at least 100 mm (3.94 in.).

R12213
A
B
Matchmarks
Manual Steering: SR-14
- STEERINGNON-TIL T STEERING COLUMN
1996 TERCEL (RM440U)
4. REMOVE CENTER UPPER INSTRUMENT CLUSTER
FINISH PANEL
(a) Remove the screw.
(b) Remove the 3 clips.
5. REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 6 screws.
6. REMOVE FRONT DOOR SCUFF PLATE AND COWL
SIDE TRIM
Remove the clip and trim.
7. REMOVE LOWER INSTRUMENT COVER AND
INSTRUMENT PANEL LOWER PAD INSERT
(a) Remove the 2 opening covers from the instrument cover.
(b) Remove the 2 screws and disconnect the hood lock re-
lease lever from the instrument cover.
(c) Remove the 4 panel cover set bolts.
(d) Remove the lower pad insert from the instrument cover.
8. REMOVE NO.2 HEATER TO REGISTER DUCT
(a) Disconnect the junction block No.1 with the 3 screws.
(b) Remove the clip.
9. REMOVE COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Disconnect the 3 connectors.
(b) w/ Airbag:
Disconnect the airbag connector.
(c) w/ Airbag:
Remove the 3 screws.
10. REMOVE SPIRAL CABLE (See page BE-14)
NOTICE:
Do not disassemble the cable or apply oil to it.
11. REMOVE COLUMN HOLE COVER
Remove the 4 nuts.
12. DISCONNECT SLIDING YOKE
(a) Place matchmarks on the yoke and steering pinion shaft/
control valve shaft.
(b) Loosen bolt A and remove bolt B.

SR17V-02
R12213
A
B
Matchmarks
Manual Steering: SR-20
- STEERINGNON-TIL T STEERING COLUMN
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL STEERING COLUMN ASSEMBLY
(a) Torque the 4 column assembly set nuts.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(b) Connect the connector.
2. CONNECT SLIDING YOKE
(a) Align the matchmarks on the sliding yoke and steering
pinion shaft/control valve shaft.
(b) Torque the bolt B.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(c) Torque the bolt A.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
3. INSTALL COLUMN HOLE COVER
Torque the 4 nuts.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
4. w/ Airbag:
INSTALL SPIRAL CABLE (See page BE-14)
5. INSTALL COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Tighten the 3 screws.
(b) w/ Airbag:
Connect the airbag connector.
(c) Connect the 3 connectors.
6. INSTALL NO.2 HEATER TO REGISTER DUCT
(a) Install the clip.
(b) Connect the junction block No.1 with the 3 screws.
7. INSTALL LOWER INSTRUMENT COVER AND
INSTRUMENT PANEL LOWER PAD INSERT
(a) Install the pad insert to cover.
(b) Tighten the 4 panel set bolts.
(c) Connect the hood lock release lever with the 2 screws.
(d) Install the 2 opening covers.
8. INSTALL FRONT DOOR SCUFF PLATE AND COWL
SIDE TRIM
Install the clip and trim.
9. INSTALL UPPER AND LOWER COLUMN COVERS
Tighten the 6 screws.
10. INSTALL CENTER UPPER INSTRUMENT CLUSTER
FINISH PANEL
(a) Connect the connector.
(b) Tighten screw.

N12792
N12793
Junction Block Side BE-12
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCH
1996 TERCEL (RM440U)
(f) Connect the negative (-) lead from the battery to terminal
8.
(g) Disconnect the negative (-) lead from the battery to termi-
nal 4.
(h) Check that the chime stops sounding.
If operation is not as specified, replace the relay.
4. INSPECT INTEGRATION RELAY CIRCUIT
Remove the relay from the instrument panel junction block and
inspect the connectors on the junction block side.
Tester connectionConditionSpecified condition
4 - GroundKey unlock warning switch OFFNo continuity
4 - GroundKey unlock warning switch ONContinuity
5 - GroundBuckle switch OFF
(Seat belt unfastened)No continuity
5 - GroundBuckle switch ON
(Seat belt fastened)Continuity
7 - GroundConstantContinuity
8 - GroundDriver's door courtesy switch OFFNo continuity
8 - GroundDriver's door courtesy switch ONContinuity
11 - GroundLight control switch OFFNo continuity
11 - GroundLight control switch TAIL or HEADContinuity
2 - GroundIgnition switch LOCK or ACCNo voltage
2 - GroundIgnition switch ONBattery positive voltage
3 - GroundConstantBattery positive voltage
9 - GroundIgnition switch LOCK or ACCNo voltage
9 - GroundIgnition switch ONBattery positive voltage
12 - GroundConstantBattery positive voltage
If the circuit is as specified, try replacing the relay with a new
one.
If the circuit is not as specified, inspect the circuits connected
to other parts.

BO47Z-01
BO5841
N12299
BO5232
BO1689
BO-34
- BODYWINDSHIELD
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE WIPER ARMS AND COWL LOUVER (See
page BO-27)
2. REMOVE FRONT PILLAR GARNISHES
Remove the garnishes by pulling.
3. REMOVE INNER REAR VIEW MIRROR
Remove the 2 bolts and the inner rear view mirror.
4. REMOVE WINDSHIELD MOULDING
Using a knife, cut off the moulding as shown.
NOTICE:
Do not damage the body with the knife.
5. REMOVE WINDSHIELD GLASS
(a) Push piano wire through between the body and glass
from the interior.
(b) Tie both wire ends to wooden blocks or like object.
HINT:
Apply adhesive tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating, take care not to damage the paint and in-
terior and exterior ornaments. To prevent scratching the
safety pad when removing the windshield, place a plastic
sheet between the piano wire and safety pad.
(c) Cut the adhesive by pulling the piano wire around it.
(d) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.

BO342-01
Z16117
: 4 Clips
Z16118
: 2 Clips
: 5 Clips
N12584
N12581
N12585
- BODYQUARTER WINDOW GLASS
BO-39
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE REAR SEAT CUSHION
2. REMOVE REAR SEATBACK
3. REMOVE FRONT SEAT OUTER BELT
4. REMOVE PACKAGE TRAY TRIM SIDE COVER
5. REMOVE REAR SEAT OUTER BELT
6. REMOVE QUARTER TRIM BOARD
7. REMOVE FRONT DOOR SCUFF PLATE
8. REMOVE ROOF SIDE INNER GARNISH
9. REMOVE QUARTER WINDOW GLASS
(a) Push piano wire through between body and glass from
the interior.
(b) Tie both wire ends to wooden blocks or similar object.
HINT:
Apply adhesive tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating the glass, take care not to damage the
paint and exterior.
(c) Cut the adhesive by pulling the piano wire around it.
HINT:
Cut the adhesive areas as shown in the illustration, leaving the
adhesive where the pins are.
(d) Using piano wire, as shown in the illustration, cut off the
rest of the adhesive.
(e) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.

BO347-01
N12292
N12291
N12055
BO-48
- BODYINSTRUMENT PANEL
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE FRONT PILLAR GARNISHES
2. REMOVE COWL SIDE TRIMS
3. REMOVE FRONT DOOR SCUFF PLATES
4. REMOVE STEERING WHEEL (See page SR-13)
5. REMOVE LOWER INSTRUMENT COVER
(a) Remove the 2 screws and the hood lock release lever.
(b) Remove the 2 hole covers.
(c) Remove the 4 bolts and the lower cover.
6. REMOVE INSTRUMENT PANEL LOWER PAD
7. REMOVE CENTER UPPER CLUSTER FINISH PANEL
8. REMOVE STEERING COLUMN COVERS
9. REMOVE COMBINATION SWITCH
10. REMOVE COMBINATION METER
11. REMOVE LOWER CENTER FINISH PANEL
(a) Remove the 4 bolts and 3 screws.
(b) Remove the instrument finish panel by pulling.
12. DISCONNECT FRONT PASSENGER AIRBAG CON-
NECTOR (See page RS-21)
13. REMOVE SHIFTING HOLE BEZEL
14. REMOVE CONSOLE BOX
15. REMOVE LOWER CENTER FINISH PANEL
16. REMOVE CENTER CLUSTER FINISH PANEL
17. REMOVE ASH RECEPTACLE BOX
18. REMOVE RADIO ASSEMBLY
19. REMOVE HEATER CONTROL PANEL (See page
AC-70)
20. REMOVE JUNCTION BLOCK NO. 1
Remove the 3 screws and J/B No. 1.

I01387
Condition : Periodically cools and then fails to cool
I01388
Condition: Insufficient cooling
- AIR CONDITIONINGAIR CONDITIONING SYSTEM
AC-5
1996 TERCEL (RM440U)
(2) Moisture present in refrigeration system.
Symptom seen in
refrigeration systemProbable causeDiagnosisRemedy
During operation, pressure on low
pressure side sometimes become
a vacuum and sometime normal
Moisture entered in refrigeration
system freezes at expansion valve
orifice and temporarily stops cycle,
but normal state is restored after a
time when the ice melts Drier in oversaturated state
 Moisture in refrigeration system
freezes at expansion valve orifice
and blocks circulation of refriger-
ant(1) Replace condenser
(2) Remove moisture in cycle
through repeatedly evacuating air
(3) Charge proper amount of new
refrigerant
(3) Insufficient cooling
Symptom seen in
refrigeration systemProbable causeDiagnosisRemedy
 Pressure low on both low and
high pressure sides
 Bubbles seen in sight glass con-
tinuously
 Insufficient cooling performance
Gas leakage at some place in re-
frigeration system Insufficient refrigerant in system
 Refrigerant leaking
(1) Check for gas leakage with gas
leak detector and repair if neces-
sary
(2) Charge Proper amount of re-
frigerant
(3) If indicated pressure value is
near 0 when connected to gauge,
create the vacuum after inspecting
and repairing the location of the
leak

AC1CX-02
- AIR CONDITIONINGCONDENSER
AC-49
1201 Author
: Date
:
1996 TERCEL (RM440U)
CONDENSER
ON-VEHICLE INSPECTION
1. INSPECT CONDENSER FINS FOR BLOCKAGE OR DAMAGE
If the fins are clogged, wash them with water and dry with compressed air.
NOTICE:
Be careful not to damage the fins.
If the fins are bent, straighten them with a screwdriver or pliers.
2. INSPECT CONDENSER AND FITTINGS FOR LEAKAGE
Repair as necessary.

AC2X0-02
AC-52
- AIR CONDITIONINGEVAPORATOR
1204 Author
: Date
:
1996 TERCEL (RM440U)
EVAPORATOR
INSPECTION
1. REMOVE EVAPORATOR (See page AC-27)
2. INSPECT FINS FOR BLOCKAGE
If the fins are clogged, clean them with compressed air.
NOTICE:
Never use water to clean the evaporator.
3. INSPECT FITTINGS FOR CRACKS OR SCRATCHES
Repair as necessary.
4. REINSTALL EVAPORATOR (See page AC-30)