drain plug TOYOTA TERCEL 1996 Service Repair Manual

SS0NA-03
SS-14
- SERVICE SPECIFICATIONSCOOLING
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Drain plug x Cylinder block2525018
Water pump x Cylinder block17.517513
Oil dipstick guide x RH engine mounting bracket18.518514
Water inlet pipe x Cylinder block7.57565 in.´lbf
Intake manifold stay x Cylinder block2020015
Water inlet x Water outlet housing5.05043 in.´lbf
Radiator upper support x Body121209
Oil cooler x Radiator lower tank Nut A
Nut B, C15.0
8.5150
8511
75 in.´lbf
No. 1 cooling fan x Radiator7.07061 in.´lbf
No. 2 cooling fan x Radiator7.07061 in.´lbf

SS0NC-01
SS-16
- SERVICE SPECIFICATIONSLUBRICATION
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Clutch release cylinder x Transaxle case M/T only121209
Drain plug x Oil pan2525018
Oil pump x Oil pump pulley3737027
Oil pump x Cylinder block7.57565 in.´lbf
Pressure regulator valve x Cylinder block3030022
Oil strainer x Cylinder block101007
Oil pan x Cylinder block1313010
Oil pan x Oil pump1313010
Front exhaust pipe x Exhaust manifold6263046
Compressor mounting bracket x Cylinder block2727020
A/C compressor x Compressor mounting bracket2525018

SS0KQ-04
- SERVICE SPECIFICATIONSMANUAL TRANSAXLE
SS-27
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head
14 mm head
10 mm head64
46
7.4650
470
7547
34
65 in.´lbf
Engine left mounting bracket x Insulator4849036
Engine rear mounting insulator x Body7880058
Engine rear mounting insulator x Bracket B bolt
C bolt64
90650
92047
67
Front exhaust pipe clamp set bolt1919014
Front exhaust pipe x Exhaust manifold6263046
Starter x Transaxle3940029
Clutch release cylinder x Transaxle121209
Shift lever assembly x Body121209
Grommet retainer x Body4.95043 in.´lbf
Retainer x Body4.95043 in.´lbf
Output shaft front bearing lock plate set bolt1111 58
Transmission case x Transaxle case2930022
Reverse shift arm bracket1717513
Straight screw plug (Reverse restrict pin) (C151)
Straight screw plug13
13130
1309
9
Straight screw plug (Shift fork shaft)2525018
Straight screw plug (Lock ball assembly) (C151)
Straight screw plug (C141)39
39400
40029
29
Reverse idler gear shaft lock bolt2930022
Rear bearing retainer2728020
Output shaft lock nut11 81,20087
Shift fork and shift head x Shift fork shaft1616012
Shift and select lever assembly2020014
Transmission case x Transmission case cover1818513
Back-up light switch4041030
Filler and drain plugs3940029
Ring gear x Differential case1241,26091
Speedometer driven gear1111 58
Control lever housing support bracket x Transmission case1111 58
Selecting bellcrank assembly x Transmission case2525018
Shift and select lever shaft assembly lock bolt2930022
Transaxle case receiver x Transaxle case1111 58
No. 1 and No. 2 oil receiver pipe1717513

SS0LL-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A132L)
SS-29
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug4950036
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C
Bolt D7.4
25
46
6475
250
470
65065 in.´lbf
18
34
47
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

SS0LJ-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
SS-31
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug1717513
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C7.4
64
4675
650
47065 in.´lbf
47
34
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

CO0HR-04
P20196
Drain Plug
Drain Plug
CO-2
- COOLINGCOOLANT
1996 TERCEL (RM440U)
REPLACEMENT
1. DRAIN ENGINE COOLANT
(a) Remove the radiator cap.
CAUTION:
To avoid the danger of being burned, do not remove the ra-
diator cap while the engine and radiator are still hot, as fluid
and steam can be blown out under pressure.
(b) Loosen the radiator drain plug (on the right side of the ra-
diator lower tank) and engine drain plug (on the left front
of the cylinder block), and drain the coolant.
(c) Close the drain plugs.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
2. FILL ENGINE COOLANT
(a) Slowly fill the system with coolant.

Use a good brand of ethylene-glycol base coolant
and mix it according to the manufacturer's direc-
tions.

Using coolant which includes more than 50 % ethyl-
ene-glycol (but not more than 70 %) is recom-
mended.
NOTICE:

Do not use an alcohol type coolant.

The coolant should be mixed with demineralized wa-
ter or distilled water.
Capacity (w/ Heater):
M/T4.9 liters (5.2 US qts, 4.3 lmp. qts)
A/T5.3 liters (5.6 US qts, 4.7 lmp. qts)
(b) Install the radiator cap.
(c) Start the engine, and bleed the cooling system.
(d) Refill the radiator reservoir with coolant until it reaches the
ºFULLº line.
3. CHECK ENGINE COOLANT FOR LEAKS

CO0HT-04
P21028
(b)
(c)
(a)
P21132
(2)(1)(b)
(a)
P21130
P21029
CO-4
- COOLINGWATER PUMP
1996 TERCEL (RM440U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE GENERATOR
3. REMOVE INTAKE MANIFOLD STAY
(a) Disconnect the engine wire clamps from the intake man-
ifold stay.
(b) Remove the bolt, nut and intake manifold stay.
4. REMOVE WATER INLET PIPE
(a) Disconnect the water inlet hose.
(b) Disconnect the heater inlet hose.
(c) Disconnect the water bypass hose.
(d) Remove the bolt, water inlet pipe and O-ring.
5. REMOVE OIL DIPSTICK GUIDE AND GENERATOR
ADJUSTING BAR
(a) Disconnect the engine wire clamp.
(b) Disconnect the connector clamp for crankshaft position
sensor.
(c) Remove the oil dipstick.
(d) Remove the mounting bolt of the dipstick guide clamp and
generator adjusting bar.
(e) Pull out the dipstick guide. Plug the guide installation hole
of the oil pump.
(f) Remove the O-ring from the dipstick guide.
6. REMOVE WATER PUMP
Remove the bolt, 2 nuts and water pump.

CO0Y2-02
(b)
(a)
P20609
(c)(d)
P20754
Plug
(e)
P20755
A/T
(A)
P20610
Radiator Lower Hose
Radiator Lower Support CO-16
- COOLINGRADIATOR
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE ENGINE UNDER COVERS
2. DRAIN ENGINE COOLANT
3. REMOVE RADIATOR RESERVOIR TANK ASSEMBLY
4. REMOVE RADIATOR ASSEMBLY
(a) Disconnect the No.1 cooling fan connector.
(b) w/ A/C:
Disconnect the No.2 cooling fan connector.
(c) Disconnect the radiator upper hose from the radiator.
(d) Disconnect the radiator lower hose from the water inlet.
(e) Disconnect the 2 A/T oil cooler hoses from the radiator.
HINT:
Plug the hose to prevent oil from escaping.
(f) Remove the 2 bolts and 2 upper radiator supports.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
HINT:
(A/T only):
After installation, check that the rubber cushion (A) of the sup-
port is not depressed.
(g) Remove the radiator assembly.
(h) Remove the 2 radiator lower supports and the lower ra-
diator hose.

P21775
H
P21097
SST
CO0766
Clearance
Lock
Plate
O-Ring
- COOLINGRADIATOR
CO-21
1996 TERCEL (RM440U)
(b) Check the lock plate height (H) after completing the caulk-
ing.
Plate height: 7.75 - 8.25 mm (0.305 - 0.325 in.)
If not within the specified height, adjust the stopper bolt of the
handle again and perform the caulking again.
6. INSPECT FOR WATER LEAKS
(a) Tighten the drain plug.
(b) Plug the inlet and outlet pipes of the radiator with SST.
SST 09230-01010
(c) Using a radiator cap tester, apply pressure to the radiator.
Test pressure: 177 kPa (1.8 kgf/cm
2, 26 psi)
(d) Inspect for leaks.
HINT:
On radiators with resin tanks, there is a clearance between the
tank and lock plate where a minute amount of air will remain,
giving the appearance of an air leak when the radiator is sub-
merged in water. Therefore, before performing the water leak
test, first move radiator around in the water until all air bubbles
disappear.
7. PAINT LOCK PLATES
HINT:
If the water leak test checks out okay, allow the radiator to com-
pletely dry and then paint the lock plates.

LU08B-04
P20919
SST
LU0490
SST
- LUBRICATIONOIL AND FILTER
LU-3
1996 TERCEL (RM440U)
REPLACEMENT
CAUTION:

Prolonged and repeated contact with mineral oil will
result in the removal of natural fats from the skin,
leading to dryness, irritation and dermatitis. In addi-
tion, used engine oil contains potentially harmful
contaminants which may cause skin cancer. Ade-
quate means of skin protection and washing facilities
should be provided.

Care should be taken, therefore, when changing en-
gine oil, to minimize the frequency and length of time
your skin is exposed to used engine oil. Protective
clothing and gloves, that cannot be penetrated by oil,
should be worn. Wash your skin throughly with soap
and water, or use waterless hand cleaner, to remove
any used engine oil. Do not use gasoline, thinners, or
solvents.

In order to preserve the environment, used oil must
be disposed of only at designated disposal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug and drain the oil into a contain-
er.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter.
SST 09228-06501
(b) Clean the filter contact surface on the filter mounting.
(c) Lubricate the filter rubber gasket with engine oil.
(d) Tighten filter until the gasket contacts seat of the filter
mounting. Then using SST, give it an additional 3/4 turn
to seat the filter.
SST 09228-06501
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
(b) Fill the engine with new oil.
Oil grade: See step 1 in oil oressure check
Oil capacity:
Drain and refill w/ Oil filter change
w/o Oil filter change2.8 liters (3.0 US qts, 2.5 lmp. qts)
2.6 liters (2.7 US qts, 2.3 lmp. qts)
Dry fill3.7 liters (3.9 US qts, 3.3 lmp. qts)