oil pressure TOYOTA TERCEL 1996 Service Repair Manual

MA001-24
- MAINTENANCEOUTSIDE VEHICLE
MA-1
39 Author
: Date
:
1996 TERCEL (RM440U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts.
If necessary, tighten them.
4. TIRE ROTATION
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and includiing the trunk lid operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

- PREPARATIONENGINE MECHANICAL
PP-3
50 Author
: Date
:
1996 TERCEL (RM440U)
(09248-05410)Valve Lifter Press
(09248-05420)Valve Lifter Stopper
09309-37010Transmission Bearing ReplacerCrankshaft front oil seal
09330-00021Companion Flange Holding ToolCrankshaft pulley
09550-10012Replacer Set ºBº
(09252-10010)No. 1 Replacer HandleValve guide bushing
Spark plug tube gasket
(09556-10010)Differential Drive Pinion Front
Bearing RemoverSpark plug tube gasket
09816-30010Oil Pressure Switch SocketKnock sensor
Oil pressure switch
09843-18020Diagnosis Check Wire
09950-50010Puller C Set
(09951-05010)Hanger 150Crankshaft pulley
(09952-05010)Slide ArmCrankshaft pulley
(09953-05020)Center Bolt 150Crankshaft pulley

PP18T-03
- PREPARATIONENGINE MECHANICAL
PP-7
1996 TERCEL (RM440U)
SSM (Special Service Materials)
08826-00080Seal Packing Black or equivalent
(FIPG)Camshaft bearing cap (No. 1 and
No. 2)
Cylinder head cover
Rear oil seal retainer
08826-00100Seal Packing 1282B,
THREE BOND 1282B or equivalent
(FIPG)Water outlet housing
08833-00070Adhesive 1324,
THREE BOND 1324 or equivalentSpark plug tube
Flywheel or drive plate bolt
08833-00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentOil pressure switch

PP3IT-01
- PREPARATIONMFI
PP-1 1
58 Author
: Date
:
1996 TERCEL (RM440U)
MFI
SST (Special Service Tools)
09268-41046Injection Measuring Tool Set
(09268-41091)NO.7 Union
(90405-09015)No.1 Union
09268-45012EFI Fuel Pressure Gauge
09631-22020Power Steering Hose Nut
14 x 17 mm Wrench SetFuel line flare nut
09816-30010Oil Pressure Switch SocketKnock sensor
09842-30070Wiring ºFº EFI Inspection
09843-18020Diagnosis Check Wire

PP195-01
- PREPARATIONLUBRICATION
PP-21
1996 TERCEL (RM440U)
EQUIPMENT
Oil pressure gauge
Straight edgeOil pump
Torque wrench

PP197-01
- PREPARATIONLUBRICATION
PP-23
1996 TERCEL (RM440U)
SSM (Special Service Materials)
08826-00080Seal Packing Black or equivalent
(FIPG)Oil pump
Oil pan
08833-00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentOil pressure switch

PP3IX-01
PP-42
- PREPARATIONAUTOMATIC TRANSAXLE (A132L)
89 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE (A132L)
SST (Special Service Tools)
09201-10000Valve Guide Bushing Remover &
Replacer SetSpeedometer driven gear oil seal
(09201-01080)Valve Guide Bushing Remover &
Replacer 8
09308-00010Oil Seal PullerSide gear shaft oil seal
09350-32014TOYOTA Automatic Transmission
Tool Set
(09351-32010)One-way Clutch Test Tool
(09351-32020)Stator Stopper
(09351-32130)Handle
(09351-32150)Oil Seal Replacer
09921-00010Spring Tension ToolSpeedometer driven gear oil seal
09992-00095Automatic Transmission Oil
Pressure Gauge SetLine pressure

PP3IY-01
- PREPARATIONAUTOMATIC TRANSAXLE (A242L)
PP-47
94 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE (A242L)
SST (Special Service Tools)
09201-10000Valve Guide Bushing Remover &
Replacer SetSpeedometer driven gear oil seal
(09201-01080)Valve Guide Bushing Remover &
Replacer 8
09308-00010Oil Seal PullerSide gear shaft oil seal
09350-32014TOYOTA Automatic Transmission
Tool Set
(09351-32010)One-way Clutch Test Tool
(09351-32020)Stator Stopper
(09351-32130)Handle
(09351-32150)Oil Seal Replacer
09921-00010Spring Tension ToolSpeedometer driven gear oil seal
09992-00095Automatic Transmission Oil
Pressure Gauge SetLine pressure

SS0N5-03
- SERVICE SPECIFICATIONSENGINE MECHANICAL
SS-5
135 Author
: Date
:
1996 TERCEL (RM440U)
ENGINE MECHANICAL
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,275 kPa (13.0 kgf/cm2, 185 psi) or more
981 kPa (10.0 kgf/cm2, 142 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Valve clearanceat cold Intake
Exhaust
Adjusting shim (for repair part) No. 02
04
06
08
10
12
14
16
18
20
22
24
26
28
30
32
340.15 - 0.25 mm (0.006 - 0.010 in.)
0.31 - 0.41 mm (0.012 - 0.016 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC110° BTDC @ idle
Idle speed-750 ± 50 rpm
Idler pulley tension
springFree length
Installed load at 47.4 mm (1.866 in.)38.4 mm (1.512 in.)
32 N (3.3 kgf, 7.3 lbf)
Cylinder headWarpage
Cylinder block side Maximum
Manifold sideMaximum
Valve guide bore diameter STD
O/S 0.05
Valve seat
Refacing angleIntake
Exhaust
Contacting angle
Contacting width
0.05 mm (0.0020 in.)
0.05 mm (0.0020 in.)
11.000 - 11.027 mm (0.4331 - 0.4342 in.)
11.050 - 11.077 mm (0.4350 - 0.4361 in.)
30°, 45°, 60°, 75°
30°, 45°, 75°
45°
1.0 - 1.4 mm (0.039 - 0.055 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD
O/S 0.056.010 - 6.030 mm (0.2366 - 0.2374 in.)
11.048 - 11.059 mm (0.4350 - 0.4354 in.)
11.098 - 11.109 mm (0.4369 - 0.4374 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum93.45 mm (3.6791 in.)
93.89 mm (3.6965 in.)
92.95 mm (3.6594 in.)
93.39 mm (3.6768 in.)
44.5°
5.970 - 5.985 mm (0.2350 - 0.2356 in.)
5.965 - 5.980 mm (0.2348 - 0.2354 in.)
0.025 - 0.060 mm (0.0010 - 0.0024 in.)
0.030 - 0.065 mm (0.0012 - 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
0.8 - 1.2 mm (0.031 - 0.047 in.)
0.5 mm (0.020 in.)

SS0N6-04
SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Cylinder head cover x Cylinder head7.07061 in.´lbf
No. 2 idler pulley x Cylinder head2828020
Camshaft timing pulley x Camshaft5151037
No. 1 idler pulley x Cylinder block18.518513
Crankshaft pulley x Crankshaft1551,55011 2
No. 2 crankshaft pulley x Crankshaft pulley1919514
RH engine mounting insulator x RH engine mounting bracket6465047
RH engine mounting insulator x Body7374054
No. 1 engine hanger x Cylinder head2121015
No. 2 engine hanger x Cylinder head5353038
Cylinder head x Cylinder block 1st
2nd45
Turn 90°450
Turn 90°33
Turn 90°
Camshaft bearing cap x Cylinder head131309
Intake manifold x Cylinder head19.519514
Intake manifold stay x Intake manifold2020015
Intake manifold stay x Cylinder block2020015
Exhaust manifold x Cylinder head4848035
Exhaust manifold stay x Cylinder block4040029
Exhaust manifold stay x Exhaust manifold4040029
Exhaust manifold heat insulator x Exhaust manifold8.08069 in.´lbf
Water outlet housing x Cylinder head3030022
Camshaft position sensor x Cylinder head8.08069 in.´lbf
EGR VSV x Cylinder head17.517513
EGR valve x Cylinder head17.517513
EGR pipe x EGR valve4040029
EGR pipe x Intake manifold3030022
PS ump bracket x Cylinder head4344032
Fuel inlet hose x Fuel filter2930022
Front exhaust pipe x Exhaust manifold6263049
Connecting rod cap x Connecting rod4040029
Crankshaft bearing cap x Cylinder block5858042
Rear oil seal retainer x Cylinder block7.57565 in.´lbf
Oil filter union x Cylinder block2525018
Oil pressure switch x Cylinder block131309
RH engine mounting bracket x Cylinder block5959043
Knock sensor x Cylinder block4545033
Generator bracket x Cylinder block2424018
Rear end plate x Cylinder block101007
Flywheel x Crankshaft9090065
Drive plate x Crankshaft9090065
Drive plate x Torque converter clutch2525018
A/C compressor bracket x Cylinder block2728020
PS pump adjusting strut x Cylinder block2121015