tires TOYOTA TERCEL 1996 Service Repair Manual

MA001-24
- MAINTENANCEOUTSIDE VEHICLE
MA-1
39 Author
: Date
:
1996 TERCEL (RM440U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts.
If necessary, tighten them.
4. TIRE ROTATION
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and includiing the trunk lid operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

MA03P-02
P19780BootBoot
P19895
- MAINTENANCECHASSIS
MA-7
45 Author
: Date
:
1996 TERCEL (RM440U)
CHASSIS
INSPECTION
1. INSPECT STEERING LINKAGE
(a) Check the steering wheel freeplay (See page SR-10).
(b) Check the steering linkage for looseness or damage.

Check that the tie rod ends do not have excessive
play.

Check that the dust seals and boots are not dam-
aged.

Check that the boot clamps are not loose.
2. INSPECT SRS AIRBAG (See page RS-2)
3. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leakage.
4. INSPECT DRIVE SHAFT BOOTS
Check the drive shaft boots for clamp looseness, leakage or
damage.
5. INSPECT BALL JOINT AND DUST COVERS
(a) Inspect the ball joints for excessive looseness.
(1) Jack up the front of the vehicle and place wooden
blocks with a height of 180 - 200 mm (7.09 - 7.87
in.) under the front tires.
(2) Lower the jack until there is about half a load on the
front coil spring. Place stands under the vehicle for
safety.
(3) Make sure the front wheels are in a straightforward
position and block the wheel with chocks.
(4) Move the lower arm up and down, and check that
the ball joint has no excessive play.
Maximum ball joint vertical play: 0 mm (0 in.)
If there is play, replace the ball joint.

AX0RI-02
(b) Check the idle speed.
(e) Check the shift linkage. (d) Check the throttle cable mark.
(f) Check the park/neutral position switch.
Check the engine and the torque converter clutch. (c) Check the fluid level and fluid condition.
STALL TEST
TIME LAG TEST PRELIMINARY CHECK
ROAD TEST HYDRAULIC TEST
MATRIX CHART (a) Check the tire inflation.
Measure the line pressure and make a basic check of fluid circuit.
Check if trouble lies within automatic transaxle. If noise or vibration occurs, the possible cause could
be with the compressor, engine, drive shaft and tires, etc. Check the automatic transaxle (each clutch, brake and gear) for wear.
(See page AX-10) AX-2
- AUTOMATIC TRANSAXLE (A132L)AUTOMATIC TRANSAXLE SYSTEM (A132L)
1996 TERCEL (RM440U)
TROUBLESHOOTING
1. GENERAL INFORMATION
(a) Troubles occurring with the automatic transaxle can be caused by either the engine or the transaxle
itself. These two areas should be checked before proceeding with troubleshooting.
(b) Troubleshooting should begin with the simplest operation, working up in order of difficulty, but first de-
termine whether the trouble lies within the engine or transaxle.
(c) Proceed with the inspection as follows:

AX-8
- AUTOMATIC TRANSAXLE (A132L)AUTOMATIC TRANSAXLE SYSTEM (A132L)
1996 TERCEL (RM440U)
EVALUATION
ProblemPossible cause
If governor pressure defect.
 Line pressure defect
 Fluid leakage in governor pressure circuit
 Governor valve operation defect
Vehicle speed (Reference)Governor pressure
30 km/h (19 mph)59 - 137 kPa (0.6 - 1.4 kgf/cm2, 9 - 20 psi)
60 km/h (37 mph)186 - 365 kPa (1.9 - 2.7 kgf/cm2, 27 - 38 psi)
90 km/h (56 mph)353 - 431 kPa (3.6 - 4.4 kgf/cm2, 51 - 63 psi)
6. ROAD TEST
NOTICE:
Do this test at normal fluid temperature 50 - 80 °C (122 - 176 °F).
(a) D position test.
Shift into the D position and while driving with the accelerator pedal held constant at the throttle valve
fully open, check on the following points:
(1) Check to seethat the 1"2 and 2"3 up-shifts take placeand also that the shift points conform
to those shown in the automatic shift schedule (See page SS-28).
EVALUATION
ProblemPossible cause
If there is no 1 - 2 up-shift. Governor valve is defective
 1 - 2 shift valve is stuck
If there is no 2 - 3 up-shift. 1 - 2 shift valve is stuck
If the shift point is defective.Throttle cable out of adjustment
 Throttle valve, 1 - 2 shift valve, 2 - 3 shift valve, etc. are defective
(2) In the same way, check the shock and slip at 1 " 2 and 2 " 3 up-shifts.
EVALUATION
ProblemPossible cause
If the shock is severe.
 Line pressure is too high
 Accumulator is defective
 Check ball is defective
(3) Run in the 3rd gear of the D position, check the abnormal noise and vibration.
HINT:
Check for the cause of abnormal noise and vibration must be made with extreme care as they could also
be due to imbalance in the drive shaft, differential, tires and torque converter clutch, etc.
(4) While running in the 3rd gear of the D position, check that the possible kick-down vehicle speed
limits for the 3 " 1 and 3 " 2 kick-down conform to those indicated in the automatic shift sched-
ule (See page SS-28).
EVALUATION
ProblemPossible cause
If the possible kick-down vehicle speed limit is defective. Throttle cable out of adjustment
 Throttle valve, 1 - 2 shift valve, 2 - 3 shift valve, etc. are defective
(5) Check the abnormal shock and slip at kick-down.
(6) While running at about 60 km/h (37 mph) in the 3rd gear of the D position, release your foot from
the accelerator pedal and shift into the L position. Then check if the 2 "1 down-shift point con-
forms to that indicated in the automatic shift schedule (See page SS-28).
(b) Inspect the lock-up mechanism.
(1) Drive in the D position at a steady speed (Lock-up ON) of about 65 km/h (40 mph).
(2) Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

AX0RV-02
(b) Check the idle speed.
(e) Check the shift linkage. (d) Check the throttle cable mark.
(f) Check the park/neutral position switch.
Check the engine and the torque converter clutch. (c) Check the fluid level and fluid condition.
STALL TEST
TIME LAG TEST PRELIMINARY CHECK
ROAD TEST HYDRAULIC TEST
MATRIC CHART (a) Check the tire inflation.
Measure the line pressure and make a basic check of fluid circuit.
Check if trouble lies within automatic transaxle. If noise or vibration occurs, the possible cause could
be with the compressor, engine, and drive shaft tires, etc. Check the automatic transaxle (each clutch, brake and gear) for wear.
(See page AX-13) AX-2
- AUTOMATIC TRANSAXLE (A242L)AUTOMATIC TRANSAXLE SYSTEM (A242L)
1996 TERCEL (RM440U)
TROUBLESHOOTING
1. GENERAL INFORMATION
(a) Troubles occurring with the automatic transaxle can be caused by either the engine or the transaxle
itself. These 2 areas should be checked before proceeding with troubleshooting.
(b) Troubleshooting should begin with the simplest operation, working up in order of difficulty degree but
first determine whether the trouble lies within the engine or the transaxle.
(c) Proceed with the inspection as follows:

AX-8
- AUTOMATIC TRANSAXLE (A242L)AUTOMATIC TRANSAXLE SYSTEM (A242L)
1996 TERCEL (RM440U)
EVALUATION
ProblemPossible cause
If there is no 1 - 2 up-shift.
Governor valve is defective

1 - 2 shift valve is stuck
If there is no 2 - 3 up-shift.
1 - 2 shift valve is stuck
If there is no 3 - O/D up-shift
(throttle valve operating less than 86%).
3 - O/D shift valve is stuck

Solenoid valve or circuit defective
If the shift point is defective.

Throttle cable out of adjustment

Throttle valve, 1 - 2 shift valve, 2 - 3 shift valve, 3 - O/D shift valve etc. are
defective
(2) In the same way, check the shock and slip at 1 " 2, 2 " 3 and 3 "O/D up-shifts.
EVALUATION
ProblemPossible cause
If the shock is severe.

Line pressure is too high

Accumulator is defective

Check ball is defective
(3) Run in the 3rd gear or O/D of the D position, check the abnormal noise and vibration.
HINT:
Check for the cause of abnormal noise and vibration must be made with extreme care as they could also
be due to unbalance in the drive shaft, differential, tires and torque converter clutch, etc.
(4) While running in the 3rd gear or O/D of the D position, check that the possible kick-down vehicle
speed limits for the 3 " 1, 3 " 2 and O/D "2 kick-down conform to those indicated in the auto-
matic shift schedule (See page SS-30).
EVALUATION
ProblemPossible cause
If the possible kick-down vehicle speed limit is defective.

Throttle cable out of adjustment

Throttle valve, 1 - 2 shift valve, 2 - 3 shift valve, 3 - O/D shift valve etc. are
defective
(5) Check the abnormal shock and slip at kick-down.
(6) While running at about 60 km/h (37 mph) in the O/D of the D position, release your foot from the
accelerator pedal and shift into the L position. Then check if the 2 "1 down-shift point conforms
to that indicated in the automatic shift schedule (See page SS-30).
(b) Inspect the lock-up mechanism.
(1) Drive in the D position at a steady speed (Lock-up ON) of about 70 km/h (43 mph).
(2) Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
If there is a big jump in engine RPM, there is no lock-up.
(c) 2 position test.
(1) While running in the 2nd gear of the 2 position, release the accelerator pedal and check the en-
gine braking effect.
EVALUATION
ProblemPossible cause
If these is no engine braking effect.
2nd coast brake is defective.
(2) Check the abnormal noise during acceleration and deceleration.
(3) Check the shock during up-shift and down-shift.
(d) L position test.
(1) While running in the L position, check that there is no up-shift to 2nd gear.
(2) While running in the L position, release the accelerator pedal and check the engine braking ef-
fect.

SA110-03
R03031
R15157
Front
R07928
SA-2
- SUSPENSION AND AXLETIRE AND WHEEL
818 Author
: Date
:
1996 TERCEL (RM440U)
TIRE AND WHEEL
INSPECTION
1. INSPECT TIRE
(a) Check the tires for wear and for the proper inflation pres-
sure.
Cold inflation pressure
Tire sizeFront
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
155SR13 AS240 (2.4, 34)225 (2.25, 32)
(b) Check the tire runout.
Tire runout: 1.4 mm (0.055 in.) or less
2. ROTATING TIRES
HINT:
See the illustration for where to rotate each tire.
3. INSPECT WHEEL BALANCE
(a) Check and adjust the Off-the-car balance.
(b) If necessary, check and adjust the On-the-car balance.
Unbalance after adjustment: 8.0 g (0.018 lb) or less

SR05N-06
SR-2
- STEERINGTROUBLESHOOTING
922 Author
: Date
:
1996 TERCEL (RM440U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in the order shown. If necessary, repair or replace these parts.
SymptomSuspect AreaSee page
Hard steering
1. Tires (Improperly inflated)
2. Power steering fluid level (Low)
3. Drive belt (Loose)
4. Front wheel alignment (Incorrect)
5. Steering system joints (Worn)
6. Suspension arm ball joints (Worn)
7. Steering column (Binding)
8. Power steering gearSA-2
SR-6
SR-3
SA-4
-
SA-36
-
SR-46
Poor return
1. Tires (Improperly inflated)
2. Front wheel alignment (Incorrect)
3. Steering column (Binding)
4. Power steering gearSA-2
SA-4
-
SR-46
Excessive play
1. Steering system joints (Worn)
2. Suspension arm ball joints (Worn)
3. Intermediate shaft, Sliding yoke (Worn)
4. Front wheel bearing (Worn)
5. Power steering gear-
SA-36
-
SA-10
SR-46
Abnormal noise
1. Power steering fluid level (Low)
2. Steering system joints (Worn)
3. Power steering gearSR-6
-
SR-46

SR4208
Maximum
Freeplay
30 mm (1.18 in.)SR05R-1 1
R12030
SR-10
- STEERINGSTEERING WHEEL
930 Author
: Date
:
1996 TERCEL (RM440U)
STEERING WHEEL
INSPECTION
1. CHECK STEERING WHEEL FREEPLAY
With the vehicle stopped and tires pointed straight ahead, rock
the steering wheel gently back and forth with light finger pres-
sure.
Freeplay should not exceed the maximum.
Maximum freeplay: 30 mm (1.18 in.)
2. CHECK STEERING EFFORT
(a) Center the steering wheel.
(b) Remove the steering wheel pad (See page SR-13).
(c) Start the engine and run it at idle.
(d) Measure the steering effort in both directions.
Reference: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
HINT:
Be sure to consider the tire type, pressure and contact surface
before making your diagnosis.
(e) Torque the steering wheel set nut.
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
(f) Install the steering wheel pad (See page SR-20).

R05752
SST
AB0164
R04211
Tires
(3 or more)Inner Diam.
Width RS-16
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
1996 TERCEL (RM440U)
(d) Install the SST.
CAUTION:
Place the disc wheel on level ground.
Connect the SST connector to the steering wheel pad
connector.
SST 09082-00700
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, pro-
vide some slack for the SST wire harness inside the disc
wheel.
(e) Cover the steering wheel pad with cardboard box or tires.

Covering method using cardboard box:
Cover the steering wheel pad with the cardboard
box and weight the cardboard box down in 4 places
with at least 190 N (20 kg, 44 lb).
Size of cardboard box:
Must exceed the following dimensions:
x= 460 mm (18.11 in.)
When dimension y of the cardboard box exceeds the
diameter of the disc wheel with tire to which the steer-
ing wheel pad is tied -
x= 460 mm (18.11 in.) + width of tire
y= 650 mm (25.59 in.)
NOTICE:
If a cardboard box smaller than the specified size is used,
the cardboard box will be broken by the shock of the airbag
deployment.

Covering method using tires:
Place at least 3 tires without disc wheel on top of the
disc wheel with tire to which the steering wheel pad
is tied.
Tire size: Must exceed the following dimensions-
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:
Do not use tires with disc wheels.