wheel torque TOYOTA TERCEL 1996 Service Repair Manual

MA02M-05
- MAINTENANCEBODY
MA-9
47 Author
: Date
:
1996 TERCEL (RM440U)
BODY
INSPECTION
1. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten the front seat-to-body mounting bolts.
Torque: 37 N´m (375 kgf´cm, 27 ft´lbf)
(b) Under Severe Conditions:
In addition to the above maintenance items, check for
loose or missing nuts and bolts on the steering system,
drive train, suspension system, fuel tank mounts, engine
mounts, etc.
2. FINAL INSPECTION
(a) Check the operation of the body parts:

Hood:
Auxiliary catch operates properly
Hood locks securely when closed

Front and rear doors:
Door lock operates properly
Doors close properly

Luggage compartment door:
Door lock operates properly

Seats:
Seat adjusts easily and locks securely in any posi-
tion
Front seat back locks securely in any position
Folding-down rear seat backs lock securely
(b) Road test:

Check the engine and chassis for abnormal noises.

Check that the vehicle does not wander or pull to
one side.

Check that the brakes work properly and do not
drag.
(b) Be sure to deliver a clean car.
Especially check the steering wheel, shift lever knob, all
switch knobs, door handles and seats.

PP0MS-07
PP-72
- PREPARATIONSUPPLEMENTAL RESTRAINT SYSTEM
1996 TERCEL (RM440U)
EQUIPMENT
Torque wrench
Bolt
Length: 35 mm (1.38 in.)
Pitch: 1.0 mm (0.039 in.)
Diam: 6.0 mm (0.236 in.)Airbag disposal
Tire
Width: 185 mm (7.28 in.)
Inner diam: 360 mm (14.17 in.)Airbag disposal
Tire with disc wheel
Width: 185 mm (7.28 in.)
Inner diam: 360 mm (14.17 in.)Airbag disposal
Vinyl bagAirbag disposal

SS0N6-04
SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Cylinder head cover x Cylinder head7.07061 in.´lbf
No. 2 idler pulley x Cylinder head2828020
Camshaft timing pulley x Camshaft5151037
No. 1 idler pulley x Cylinder block18.518513
Crankshaft pulley x Crankshaft1551,55011 2
No. 2 crankshaft pulley x Crankshaft pulley1919514
RH engine mounting insulator x RH engine mounting bracket6465047
RH engine mounting insulator x Body7374054
No. 1 engine hanger x Cylinder head2121015
No. 2 engine hanger x Cylinder head5353038
Cylinder head x Cylinder block 1st
2nd45
Turn 90°450
Turn 90°33
Turn 90°
Camshaft bearing cap x Cylinder head131309
Intake manifold x Cylinder head19.519514
Intake manifold stay x Intake manifold2020015
Intake manifold stay x Cylinder block2020015
Exhaust manifold x Cylinder head4848035
Exhaust manifold stay x Cylinder block4040029
Exhaust manifold stay x Exhaust manifold4040029
Exhaust manifold heat insulator x Exhaust manifold8.08069 in.´lbf
Water outlet housing x Cylinder head3030022
Camshaft position sensor x Cylinder head8.08069 in.´lbf
EGR VSV x Cylinder head17.517513
EGR valve x Cylinder head17.517513
EGR pipe x EGR valve4040029
EGR pipe x Intake manifold3030022
PS ump bracket x Cylinder head4344032
Fuel inlet hose x Fuel filter2930022
Front exhaust pipe x Exhaust manifold6263049
Connecting rod cap x Connecting rod4040029
Crankshaft bearing cap x Cylinder block5858042
Rear oil seal retainer x Cylinder block7.57565 in.´lbf
Oil filter union x Cylinder block2525018
Oil pressure switch x Cylinder block131309
RH engine mounting bracket x Cylinder block5959043
Knock sensor x Cylinder block4545033
Generator bracket x Cylinder block2424018
Rear end plate x Cylinder block101007
Flywheel x Crankshaft9090065
Drive plate x Crankshaft9090065
Drive plate x Torque converter clutch2525018
A/C compressor bracket x Cylinder block2728020
PS pump adjusting strut x Cylinder block2121015

SS0KS-01
SS-24
- SERVICE SPECIFICATIONSCLUTCH
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Clutch line union1515511
Master cylinder installation nut121209
Bleeder plug8.38574 in.´lbf
Clutch cover x Flywheel1919514
Release cylinder installation bolt121209

SS0LK-02
SS-28
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A132L)
158 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE (A132L)
SERVICE DATA
Governor pressure Vehicle speed reference
30 km/h (19 mph)
60 km/h (37 mph)
90 km/h (56 mph)
59 - 137 kPa (0.6 - 1.4 kgf/cm2, 9 - 20 psi)
186 - 265 kPa (1.9 - 2.7 kgf/cm2, 27 - 38 psi)
353 - 431 kPa (3.6 - 4.4 kgf/cm2, 51 - 63 psi)
Line pressure (Wheel locked)
Engine Idling D position
R position
AT stall (Throttle valve fully opened) D position
R position
363 - 422 kPa (3.7 - 4.3 kgf/cm2, 53 - 61 psi)
530 - 706 kPa (5.4 - 7.2 kgf/cm2, 77 - 102 psi)
902 - 1,049 kPa (9.2 - 10.7 kgf/cm2, 131 - 152 psi)
1,412 - 1,647 kPa (14.4 - 16.8 kgf/cm2, 205 - 239 psi)
Engine stall revolution D and R positions2,300 ± 200 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF) N position750 ± 50 rpm
Throttle cable adjustment (Throttle valve fully opened)
Between boot end face and inner cable stopper
0 - 1 mm (0 - 0.04 in.)
Torque converter clutch installation distance
Drive plate runoutMax.
Torque converter clutch runout Max.More than 13.0 mm (0.512 in.)
0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
Differential oil seal drive in depth0 ± 0.5 mm (0 ± 0.020 in.)
Speedometer driven gear oil seal drive in depth19 mm (0.75 in.)
Shift Point
D position
Throttle valve fully opened 1 "2
2 " 3
3 " 2
2 " 1
L position
Throttle valve fully closed 2 " 1
47 - 62 km/h (29 - 39 mph)
91 - 107 km/h (57 - 66 mph)
85 - 104 km/h (53 - 65 mph)
36 - 46 km/h (22 - 29 mph)
39 - 49 km/h (24 - 30 mph)
Lock-up point
D position
Throttle valve fully closed Lock-up ON
Lock-up OFF
63 - 72 km/h (39 - 45 mph)
59 - 68 km/h (37 - 42 mph)

SS0LI-04
SS-30
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
160 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE (A242L)
SERVICE DATA
Governor pressure Vehicle speed reference
30 km/h (19 mph)
60 km/h (37 mph)
90 km/h (56 mph)
59 - 137 kPa (0.6 - 1.4 kgf/cm2, 9 - 20 psi)
196 - 275 kPa (2.0 - 2.8 kgf/cm2, 28 - 40 psi)
363 - 441 kPa (3.7 - 4.5 kgf/cm2, 53 - 64 psi)
Line pressure (Wheel locked)
Engine Idling D position
R position
AT stall (Throttle valve fully opened) D position
R position
373 - 422 kPa (3.8 - 4.3 kgf/cm2, 54 - 61 psi)
549 - 706 kPa (5.6 - 7.2 kgf/cm2, 80 - 102 psi)
902 - 1,049 kPa (9.2 - 10.7 kgf/cm2, 131 - 152 psi)
1,638 - 1,902 kPa (16.7 - 19.4 kgf/cm2, 238 - 276 psi)
Engine stall revolution D and R positions2,300 ± 200 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF) N position750 ± 50 rpm
Throttle cable adjustment (Throttle valve fully opened)
Between boot end face and inner cable stopper
0 - 1 mm (0 - 0.04 in.)
Torque converter clutch installation distance
Drive plate runoutMax.
Torque converter clutch runout Max.More than 13.0 mm (0.512 in.)
0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
Differential oil seal drive in depth LH side
RH side5.3 ± 0.5 mm (0.209 ± 0.020 in.)
3.1 ± 0.5 mm (0.122 ± 0.020 in.)
Speedometer driven gear oil seal drive in depth25.0 mm (0.98 in.)
Shift Point
D position
Throttle valve fully opened 1 "2
2 " 3
3 " 2
2 " 1
Throttle valve fully closed 3 O/D
L position
Throttle valve fully closed 2 " 1
45 - 61 km/h (28 - 38 mph)
89 - 106 km/h (55 - 66 mph)
83 - 102 km/h (52 - 63 mph)
83 - 43 km/h (19 - 27 mph)
19 - 33 km/h (12 - 21 mph)
44 - 56 km/h (27 - 35 mph)
Lock-up point
D position
Throttle valve fully closed Lock-up ON
Lock-up OFF
65 - 76 km/h (40 - 47 mph)
61 - 72 km/h (38 - 45 mph)

SS0LO-07
SS-32
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
162 Author
: Date
:
1996 TERCEL (RM440U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire inflationTire sizeCold tire inflation
pressure
Tire size
155SR13 ASFront240 kPa (2.4 kgf/cm2, 34 psi)ressure 155SR13 AS Front
Rear
240 kPa (2.4 kgf/cm, 34 si)
225 kPa (2.25 kgf/cm2, 32 psi)
Vehicle heightTire size
155SR13 ASFront
Rear
187.9 mm (7.40 in.)
253.2 mm (9.97 in.)
Front wheel align-
mentToe-in (Total)
Tie rod end left-right error0.1° ± 0.2° (1 ± 2 mm, 0.04 ± 0.08 in.)
1.5 mm (0.059 in.) or less
ment
Camber
Left-right error-0°20' ± 45'
45' or less
Caster
Left-right error1°20' ± 45'
45' or less
Steering axis inclination
Left-right error12°10' ± 45'
45' or less
Wheel angle Inside wheel
Outside wheel35°55' ± 2°
32°10' (Reference)
Rear wheel align-Toe-in (Total)0.3° ± 0.3° (3 ± 3 mm, 0.12 ± 0.12 in.)Rear wheel align-
ment
Camber
Left-right error-0°30' ± 45'
45' or less
Front axleAxle bearing backlash0.05 mm (0.0020 in.) or lessFront axle
Axle hub deviation0.05 mm (0.0020 in.) or less
Front suspensionLower ball joint turning torque0.8 - 2.5 N´m (8 - 25 kgf´cm, 7 - 22 in.´lbf)
Rear axleBearing preload (turning)Add frictional force plus 0 - 11.8 N (0 - 1.2 kgf, 0 - 2.6 lbf)Rear axle
Axle hub axial play0.05 mm (0.0020 in.) or less

SS0LP-06
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-33
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT:
Disc brake dust cover x Steering knuckle8.38574 in.´lbf
Lower ball joint x Steering knuckle981,00072
Steering knuckle x Shock absorber2452,500181
Lower ball joint x Lower suspension arm8082059
Tie rod end lock nut4748035
Tie rod end x Steering knuckle4950036
Disc brake caliper x Steering knuckle8890065
Drive shaft lock nut2162,200159
Piston rod x Suspension support4747534
Suspension support x Body3940029
Flexible hose x Shock absorber2930022
Lower suspension arm x BodyFront side1421,450105Lower sus ension arm x Body Front side
Rear side
142
74
1,450
750
105
55
Hub nut1031,05076
ABS speed sensor x Steering knuckle7.88069 in.´lbf
REAR:
Piston rod x Suspension support3435025
Suspension support x Body3940029
Shock absorber x Axle beam6869050
Backing plate x Axle beam7071051
Parking brake cable x Backing plate7.88069 in.´lbf
Brake line x Wheel cylinder1515511
Body x Axle beam1421,450105
Lateral control rod x Axle beam8385061
Lateral control rod x Body11 31,15083
ABS speed sensor x Axle beam7.88069 in.´lbf
ABS speed sensor wire x Axle beam5.45548 in.´lbf

SS0M3-10
- SERVICE SPECIFICATIONSBRAKE
SS-35
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Master cylinder x Piston stopper bolt101007
Master cylinder x Reservoir1.717.515.2 in.´lbf
Master cylinder x Brake booster131309
Brake line union nut1515511
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket1414510
Front disc brake caliper installation bolt2525518
Bleeding plug8.38574 in.´lbf
Front disc brake torque plate x Steering knuckle8890065
Front disc brake caliper x Flexible hose3031022
Rear drum brake wheel cylinder x Backing plate101007
ABS actuator assembly x Body1919514
ABS actuator x ABS actuator bracket assembly5.45548 in.´lbf
ABS actuator x ABS actuator No. 3 bracket1919514
Front speed sensor x Steering knuckle8.08271 in.´lbf
Front speed sensor wire harness clamp installation bolt5.05144 in.´lbf
Rear speed sensor x Axle beam8.08271 in.´lbf
Rear speed sensor wire harness clamp installation bolt5.05144 in.´lbf

SS0N1-03
SS-36
- SERVICE SPECIFICATIONSSTEERING
166 Author
: Date
:
1996 TERCEL (RM440U)
STEERING
SERVICE DATA
ON-VEHICLE INSPECTION
Steering wheel freeplayMaximum30 mm (1.18 in.)
Drive belt tension New belt140 - 180 lbf Drive belt tension New belt
Used belt
140 180 lbf
80 - 120 lbf
Maximum rise of oil level5 mm (0.20 in.)
Oil pressure at idle speed with valve closed Minimum6,374 kPa (65 kgf/cm2, 925 psi)
Steering effort at idle speedMaximum7.8 N´m (80 kgf´cm, 69 in.lbf)
PS VANE PUMP
Rotor shaft bushing oil clearance STD0.01 - 0.03 mm (0.0004 - 0.0012 in.) Rotor shaft bushing oil clearance STD
Maximum
0.01 0.03 mm (0.0004 0.0012 in.)
0.07 mm (0.0028 in.)
Vane plate heightMinimum8.0 mm (0.315 in.)
Vane plate thickness Minimum1.77 mm (0.0697 in.)
Vane plate lengthMinimum14.97 mm (0.5894 in.)
Vane plate to rotor groove clearanceMaximum0.03 mm (0.0012 in.)
Vane plate length Pump rotor and cam ring mark Vane late length Pum rotor and cam ring mark
None14.996 - 14.998 mm (0.59039 - 0.59047 in.)None
1
14.996 - 14.998 mm (0.59039 - 0.59047 in.)
14.994 - 14.996 mm (0.59032 - 0.59039 in.)1
2
14.994 14.996 mm (0.59032 0.59039 in.)
14.992 - 14.994 mm (0.59024 - 0.59032 in.)2
3
14.992 14.994 mm (0.59024 0.59032 in.)
14.990 - 14.992 mm (0.59016 - 0.59024 in.)3
4
14.990 14.992 mm (0.59016 0.59024 in.)
14.988 - 14.990 mm (0.59008 - 0.59016 in.)
Spring free length36 - 38 mm (1.42 - 1.49 in.)
Vane pump rotating torqueMaximum0.3 N´m (2.8 kgf´cm, 2.4 in.´lbf) or less
MANUAL STEERING GEAR
Steering rack runout Maximum0.30 mm (0.0118 in.)
Pinion preload Turning0.23 - 0.32 N´m (2.3 - 3.3 kgf´cm, 2.0 - 2.9 in.lbf)
Total preload Turning0.6 - 1.2 N´m (6 - 12 kgf´cm, 5.2 - 10.4 in.´lbf)
PS GEAR
Steering rack runout Maximum0.30 mm (0.0118 in.)
Measure oil clearance STD0.050 - 0.083 mm (0.00197 - 0.00327 in.) Measure oil clearance STD
Maximum
0.050 0.083 mm (0.00197 0.00327 in.)
0.125 mm (0.00492 in.)
Total preload Turning0.8 - 1.4 N´m (8 - 14 kgf´cm, 6.9 - 12.2 in.´lbf)