engine TOYOTA TUNDRA 2008 2.G Owner's Manual

40
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
XS12001
Indicator light
XS12027a
Glass breakage sensor (on some models)
SETTING THE SYSTEM
1. Turn the key to the “LOCK” position and remove it.
The indicator light will start flashing when
the key is removed from the engine
switch. (See “Engine immobilizer system”
on page 21 in this Section for details.) 2. Have all passengers get out of the vehicle.
3. Close and lock all the doors and hood.
The indicator light will remain on when all
the doors and hood are closed and
locked.
The system will automatically be set after
30 seconds. When the system is set, the
indicator light will start flashing again. 4. After making sure the indicator light starts flashing, you may leave the ve-
hicle.
Never leave anyone in the vehicle when
you set the system, because unlocking
from the inside will activate the system. WHEN THE SYSTEM IS SET
Activating the system
The system will sound the alarm under
the following conditions:
If any of the doors is unlocked or
opened without the key or wireless re-
mote control transmitter, or if the hood
is forcibly opened
If the battery terminal is disconnected
and then reconnected
Vehicles with the glass breakage sensor—
The side windows are tapped or bro-
ken.
The indicator light will come on when the
system is activated.
If the alarm has been activated and the
key is not in the engine switch, all the
doors will re −lock automatically.
After one minute, the alarm will automati-
cally stop and the indicator light will start
flashing again.

41
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
Reactivating the alarm
Once set, the system automatically resets
the alarm after the alarm stops.
The alarm will activate again under the
same circumstances described in
“Activating the system”.
Stopping the alarm
The alarm will be stopped by the following
two ways:
Turn the engine switch from the
“LOCK” to “ON” position.
Unlock any of the doors with the key
or wireless remote control transmitter.
These ways cancel the system at the
same time. TESTING THE SYSTEM
1. Open all the windows.
2. Set the system as described above. The side doors should be locked with
the key or wireless remote control
transmitter. Be sure to wait until the
indicator light goes off or starts flash-
ing.
3. Unlock any door from the inside. The system s hould activate the alarm.
4. Stop the alarm as described above.
5. Repeat this operation for the other doors and hood. When testing the
hood, also check that the system is
activated when the battery terminal is
disconnected and then reconnected.
If the system does not work properly,
have it checked by your Toyota dealer.
XS12038c
This indicates that the fuel filler door
is on the left side of your vehicle.
Fuel tank cap

42
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
XS12020a
1. To open the fuel filler door, pull the
door toward out as shown.
When refueling, turn off the engine.
CAUTION
Do not smoke, cause sparks or al-
low open flames when refueling.
The fumes are flammable.
When opening the cap, do not re-
move the cap quickly. In hot weath-
er, fuel under pressure could cause
injury by spraying out of the filler
neck if the cap is suddenly re-
moved.
Do not fill a fuel container in the
bed under any circumstances. A
static electricity charge could cause
a spark and fire hazard. The proper
procedure is to place an approved
fuel container on the ground away
from the truck for filling.
XS12021a
2. To remove the fuel tank cap, turnthe cap slowly counterclockwise,
then pause slightly before removing
it. After removing the cap, hang it
on the cap hanger.
It is not unusual to hear a slight swoosh
when the cap is opened.
When installing the cap, turn it clock-
wise until one click is heard, in order
to fully close it. The cap returns slight-
ly when your hand is released from the
cap after closure, however this does
not cause any problems.
If the cap is not tightened securely, the
malfunction indicator lamp comes on.
Make sure the cap is tightened securely.

43
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
The indicator lamp goes off after driving
several times. If the indicator lamp does
not go off, contact your Toyota dealer as
soon as possible.
CAUTION
Make sure the cap is installed se-
curely to prevent fuel spillage in
the event of an accident.
Use only a genuine Toyota fuel tank
cap for replacement. It is designed
to regulate fuel tank pressure.
XS12058a
Sliding operation
XS12059
Tilting operation
To operate the moon roof, use the
switches on the overhead console.
The moon roof works when the engine
switch is in the “ON” position.
The sun shade can be opened or closed
by hand.
Sliding operation—
To open: Push and hold the “SLIDE”
switch for 1 second on the “
” (rear)
side.
The roof will fully open automatically. To
stop the roof partway, push one of the
moon roof switches briefly.
When you quickly push and release the
switch, the moon roof will open while the
switch is being pushed and stop when
released.
The sun shade will be opened together
with the roof.
When the moon roof is opened fully, the
deflector will raise to reduce the entering
of the strong wind. The angle of the de-
flector will be adjusted according to the
vehicle speed.
To close: Push and hold the “SLIDE”
switch for 1 second on the “
” (front)
side.
Electric moon roof (on some
Crew Max models)

44
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
The roof will fully close automatically. To
stop the roof partway, push one of the
moon roof switches briefly.
When you quickly push and release the
switch, the moon roof will close while the
switch is being pushed and stop when
released.
Tilting operation—
To tilt up: Push and hold the “TILT” switch
for 1 second on the “UP” side.
The roof will fully tilt up automatically. To
stop the roof partway, push one of the
moon roof switches briefly.
When you quickly push and release the
switch, the moon roof will tilt up while the
switch is being pushed and stop when
released.
To tilt down: Push and hold the “TILT”
switch for 1 second on the indented
(front) side.
The roof will fully tilt down automatically.
To stop the roof partway, push one of the
moon roof switches briefly.
When you quickly push and release the
switch, the moon roof will tilt down while
the switch is being pushed and stop when
released. Key off operation:
If both front doors are
closed, the moon roof works for about 43
seconds even after the engine switch is
turned off. It stops working when either
door is opened.
Jam protection function:
If something gets caught between the
moon roof and frame during slide clos-
ing operation, the moon roof stops and
opens, and the deflector stops and
raises fully.
If something gets caught between the
moon roof and frame during tilting
down operation, the moon roof stops
and opens fully.
If the moon roof receives a strong impact,
this function may work even if nothing is
caught.
If the moon roof does not operate auto-
matically or the jam protection function
does not operate correctly, you should
normalize the moon roof.
To normalize the moon roof, push and
hold the switch toward the “UP” (tilt up)
side or “
” (sliding close) side. The
moon roof will tilt up and down, then re-
lease the switch. Make sure that the moon roof opens and
closes automatically. If the moon roof can-
not be operated properly, have it checked
by your Toyota dealer.

56
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
NOTICE
To prevent damage to the seat, avoid
putting heavy loads on the temporary
table.
This system can memorize the position
of the driver’s seat, the tilt and tele-
scopic steering, and the outside rear
view mirrors, and recall them at the
touch of a button.
Buttons “1” and “2” can memorize two
separate positions.
XS13098a
SETTING THE DRIVING POSITION
The engine switch must be in the “ON”
position and the selector lever in the “P”
position.
1. Adjust the driver ’s seat, the tilt and telescopic steering, and the outside
rear view mirrors to the desired
position.
2. While pushing the “SET” button, push button “1” or “2” until a beep
in heard.
Driving position memory
system (on some models)

57
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
The system can memorize up to 2 posi-
tions by repeating the above steps. If step
2 is performed for a button that already
has a memory setting, the previous posi-
tion will be erased and the new position
will be memorized.
To make only slight changes to an already
memorized position, the easiest way is to
first activate the memorized position, then
make the desired changes and perform
step 2 above.
XS13099a
RECALLING THE MEMORIZED POSITION
When you push button “1” or “2”, a
beep will sound and the driving posi-
tion will be automatically adjusted to
the position recorded for that button.
The memorized position can be recalled
under the following conditions:
The engine switch is in the “ON” posi-
tion and the selector lever is in the “P”
position.
The key is not in the engine switch
and less than 30 seconds have passed
since opening the driver ’s door.
To stop the operation, push any driving
position memory button. To reactivate the system, push button “1”
or “2” again.
If the vehicle’s battery is disconnected,
the memory will be erased and the posi-
tions will have to be set again.
CAUTION
Do not start the vehicle while the
adjustment are being made.
Take care not to select the wrong
button, or the seat could strike the
rear passenger or hit your body
against the steering wheel. If this
happens, you can stop the move-
ment by pressing another driving
position memory switch, or de-
pressing the brake pedal.

58
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
When the driver’s door is opened, you
can recall the memorized position using
the wireless remote control system.
This function can be used after setting the
driving position with the following proce-
dure.
XS13213a
REGISTERING THE DRIVING POSITION
ONTO THE WIRELESS REMOTE
CONTROL TRANSMITTER
A wireless remote control transmitter can
memorize only one drive position.
The driver’s door must be closed with the
engine switch turned off.
1. Push and hold a previously memo- rized driving position button “1” or
“2”.
2. While depressing the abovemen- tioned button, push and hold the un-
lock button on the wireless remote
control transmitter until a beep
sounds. If you want to set another driving position,
repeat the above procedure. The previous
setting will be erased and the new posi-
tion will be set.
—Memory call system using
the wireless remote control
transmitter

59
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
XS13214a
CANCELING THE DRIVING POSITION
ONTO THE WIRELESS REMOTE
CONTROL TRANSMITTER
The driver’s door must be closed with the
engine switch turned off.
1. Push and hold the “SET” switch.
2. Push and hold the unlock button on the wireless remote control transmit-
ter until two beeps sound.
The memory on the wireless remote con-
trol transmitter is disabled. To enable it
again, repeat the above procedure.
CAUTION
Do not adjust the seat while the
vehicle is moving.
Be careful that the seat does not
hit a passenger or luggage.
Be careful not to get your hands or
feet pinched in the seat.
After adjusting the seat position, re-
lease the lever and try sliding the
seat forward and backward to make
sure it is locked in position.
After adjusting the seatback, push
your body back against the seat to
make sure the seat is locked in
position.
When returning the seatback to the
upright position, observe the follow-
ing precautions in order to prevent
death or serious injury in a colli-
sion or sudden stop:
Make sure the seatback is securely
locked by pushing forward and rear-
ward on the top of the seatback.
Failure to do so will prevent the
seat belt from operating properly.
Make sure the seat belts are not
twisted or caught in the seatback
and are arranged in their proper
position and are ready to use.
Folding down the rear seatbacks will en-
large the luggage compartment. See
“—Stowage precautions” on page 470 in
Section 2 for precautions when loading
luggage.
Rear seats—
—Rear seat precautions

65
2008 TUNDRA from Apr. ’08 Prod. (OM 34477U)
Rear center head restraint and front cen-
ter head restraint (bench seats)—When an
occupant sits on the center position of the
rear seats (Double cab and Crew Max
models) or the front seats (bench seats),
always pull up the center head restraint to
the lock position.
The head restraint is most effective when
it is close to your head. Therefore, using
a cushion on the seatback is not recom-
mended.
CAUTION
Adjust the center of the head re-
straint so that it is closest to the
top of your ears.
After adjusting the head restraint,
make sure it is locked in position.
Do not drive with the head re-
straints removed.
XS13207
To use the armrest, pull it down as
shown in the illustrations.
NOTICE
To prevent damage to the armrest,
avoid putting heavy loads on it.
XS13100c
To turn on the seat heater, move the
dial upward (“L” dial for the left front
seat or “R” dial for the right front
seat). At this time, the indicator light
will illuminate to indicate the seat heat-
er is operating.
Move the dial upward or downward to ad-
just to the desired temperature.
To turn it off, move the dial downward
until it stops.
When the seat heater is not in use, move
the dial fully downward.
The engine switch must be in the “ON”
position to operate seat heaters.
Armrest (Crew Max models) Seat heaters