fuel filter TOYOTA TUNDRA 2019 Warranties & Maintenance Guides (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2019, Model line: TUNDRA, Model: TOYOTA TUNDRA 2019Pages: 66, PDF Size: 1.34 MB
Page 37 of 66

36Maintenance Log
MAINTENANCE
Special Operating Conditions
In addition to standard maintenance items,
the maintenance log indicates services that
should be performed on vehicles that are
driven under especially demanding
conditions. These “special operating
conditions” and their required maintenance
items are clearly indicated in each chart.
NOTE:
You should perform these additional
maintenance services only if the
majority of your driving is done under
the special operating conditions
indicated. If you only occasionally
drive under these circumstances, it
is not necessary to perform the
additional services.
Engine Oil Selection
Please refer to your Owner’s Manual for the
specific oil viscosity rating recommended
for your vehicle/engine type.
Flex Fuel Vehicles (Use of E85)
When using E85 fuel, your engine oil and oil
filter may need to be replaced more often.
If using E85 fuel more than 50% of the time,
change the engine oil and oil filter every
2,500 miles or three months. If using E85 fuel
less than 50% of the time, follow the normal
engine oil and oil filter change schedule
(5,000 miles or six months).
Additional Maintenance
In addition to scheduled maintenance,
your Toyota requires ongoing general
maintenance, such as fluid checks and
visual inspections. These procedures are
explained in the “Maintenance and Care”
section of the Owner ’s Manual. Be sure
to perform these procedures regularly to
ensure the most trouble-free operation
of your vehicle.
SuperChrome and
Alloy Wheel Care
If you purchased genuine Toyota accessory
Aluminum Alloy Wheels, follow these cleaning
guidelines to maintain the appearance of
your wheels:
• If wheels are hot, wait for them to cool
before washing.
• Use a soft sponge or cotton cloth to
apply the same mild car-wash soap as
used for the vehicle body. Quickly rinse
off with water. Use a soft cloth to apply
the same car wax as used for the
vehicle body.
• DO NOT USE: Any kind of chemical-
based cleaners, alcohol, solvents,
gasoline, steam cleaners, scouring
pads, wire brushes or coarse abrasives
to clean your wheels.
USING THE MAINTENANCE LOG CHARTS
18-TCS-11469_Toyota_WMG_MY19_Tundra_FFV_GUTS_3_0_tw .indd 367/5/18 10:19 PM
Page 42 of 66

41Maintenance Log
Dealer Service verification:
D
ate: Mileage:
MAINTENANCE LOG
MAINTENANCE
27,500 miles or 33 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace engine oil and oil filter2
Dealer Service verification:
D
ate: Mileage:
30,000 miles or 36 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Re-torque propeller shaft bolt
Inspect the following:
_ Au
tomatic transmission for signs of leakage
_ Ba
ll joints and dust covers
_ Br
ake lines and hoses
_ Br
ake linings/drums and brake pads/discs
5
_ Dri ve shaft boots
_Eng
ine coolant6
_Ex haust pipes and mountings
_Fr
ont differential oil
Driving on dirt roads or dusty roads:
Replace transfer case oil
Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:
7
Replace front differential oil
Replace rear differential oil
Replace transfer case oil
Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leaka ge. If any leakage from a sealed component
is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect power steering
fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant level/condition/fre\
ezing
point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on inspection results.
2 Refer to “Engine Oil and Filter” in the “Explanation of Maintenance Items” section in the back of this guide for more information.3 Perform these service items only if you drive primarily under the conditions indicated. 4 Includes operating on roads which road salt has been applied. 5 Inspect thickness measurement and disc runout.6 Refer to “Engine Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for more information.7 Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual f or details.
_ Fu
el lines and connections, fuel tank band
and fuel tank vapor vent system hoses
_ Fu
el tank cap gasket
_Ra
diator and condenser
_Re
ar differential oil
_St
eering gear
_St
eering linkage and boots
_Tr
ansfer case oil
Replace cabin air filter
Replace engine air filter
Replace engine oil and oil filter2
Rotate tires
Additional Maintenance Items for Special Operating Conditions3
18-TCS-11469_Toyota_WMG_MY19_Tundra_FFV_GUTS_3_0_tw .indd 417/5/18 10:19 PM
Page 46 of 66

45Maintenance Log
MAINTENANCE LOG
MAINTENANCE
Dealer Service verification:
D
ate: Mileage:
57,500 miles or 69 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace engine oil and oil filter2
Dealer Service verification:
D
ate: Mileage:
60,000 miles or 72 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Re-torque propeller shaft bolt
Inspect the following:
_ Au
tomatic transmission for signs of leakage
_ Ba
ll joints and dust covers
_ Br
ake lines and hoses
_ Br
ake linings/drums and
brake pads/discs
5
_ Dri ve belts6
_Dri ve shaft boots
_Eng
ine coolant7
_Ex haust pipes and mountings
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads:
Replace transfer case oil
Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:8
Replace automatic transmission fluid
Replace front differential oil
Replace rear differential oil
Replace transfer case oil
Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leaka ge. If any leakage from a sealed component
is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect power steering
fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant level/condition/fre\
ezing
point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on inspection results.
2 Refer to “Engine Oil and Filter” in the “Explanation of Maintenance Items” section in the back of this guide for more information.3 Perform these service items only if you drive primarily under the conditions indicated. 4 Includes operating on roads which road salt has been applied. 5 Inspect thickness measurement and disc runout.6 Initial inspection at 60,000 miles/ 72 months. Inspect every 15.000 miles/18 months thereafter.7 Refer to “Engine Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for more information.8 Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual f or details.
_ Fr
ont differential oil
_ Fu
el lines and connections, fuel tank band
and fuel tank vapor vent system hoses
_ Fu
el tank cap gasket
_Ra
diator and condenser
_Re
ar differential oil
_St
eering gear
_St
eering linkage and boots
_Tr
ansfer case oil
Replace cabin air filter
Replace engine air filter
Replace engine oil and oil filter2
Rotate tires
18-TCS-11469_Toyota_WMG_MY19_Tundra_FFV_GUTS_3_0_tw .indd 457/5/18 10:21 PM
Page 50 of 66

49Maintenance Log
MAINTENANCE LOG
MAINTENANCE
Dealer Service verification:
D
ate: Mileage:
87,500 miles or 105 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace engine oil and oil filter2
Dealer Service verification:
D
ate: Mileage:
90,000 miles or 108 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Re-torque propeller shaft bolt
Inspect the following:
_ Au
tomatic transmission for signs of leakage
_ Ba
ll joints and dust covers
_ Br
ake lines and hoses
_ Br
ake linings/drums and
brake pads/discs
5
_ Dri ve belts
_Dri
ve shaft boots
_Eng
ine coolant
6
_Ex haust pipes and mountings
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads:
Replace transfer case oil
Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:
7
Replace front differential oil
Replace rear differential oil
Replace transfer case oil
Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leaka ge. If any leakage from a sealed component
is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect power steering
fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant level/condition/fre\
ezing
point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on inspection results.
2 Refer to “Engine Oil and Filter” in the “Explanation of Maintenance Items” section in the back of this guide for more information.3 Perform these service items only if you drive primarily under the conditions indicated. 4 Includes operating on roads which road salt has been applied. 5 Inspect thickness measurement and disc runout.6 Refer to “Engine Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for more information.7 Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual f or details.
_ Fr
ont differential oil
_ Fu
el lines and connections, fuel tank band
and fuel tank vapor vent system hoses
_ Fu
el tank cap gasket
_Ra
diator and condenser
_Re
ar differential oil
_St
eering gear
_St
eering linkage and boots
_Tr
ansfer case oil
Replace cabin air filter
Replace engine air filter
Replace engine oil and oil filter2
Rotate tires
18-TCS-11469_Toyota_WMG_MY19_Tundra_FFV_GUTS_3_0_tw .indd 497/5/18 10:26 PM
Page 54 of 66

53Maintenance Log
MAINTENANCE LOG
MAINTENANCE
Dealer Service verification:
D
ate: Mileage:
117,500 miles or 141 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Replace engine oil and oil filter2
Dealer Service verification:
D
ate: Mileage:
120,000 miles or 144 months
Check installation of driver’s floor mat
Inspect and adjust all fluid levels1
Inspect wiper blades
Re-torque propeller shaft bolt
Replace cabin air filter
Inspect the following:
_ Au
tomatic transmission for signs of leakage
_ Ba
ll joints and dust covers
_ Br
ake lines and hoses
_ Br
ake linings/drums and
brake pads/discs
6
_ Dri ve belts
_Dri
ve shaft boots
_Eng
ine coolant
7
_Ex haust pipes and mountings
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads:
Replace transfer case oil
Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:8
Replace automatic transmission fluid
Replace front differential oil
Replace rear differential oil
Replace transfer case oil
Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leaka ge. If any leakage from a sealed component
is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect power steering
fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant level/condition/fre\
ezing
point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on inspection results.
2 Refer to “Engine Oil and Filter” in the “Explanation of Maintenance Items” section in the back of this guide for more information.3 Perform these service items only if you drive primarily under the conditions indicated. 4 Includes operating on roads which road salt has been applied. 5 Maintenance services of spark plugs are required under the terms of the Emissions Control Warranty.6 Inspect thickness measurement and disc runout.7 Refer to “Engine Coolant” in the “Explanation of Maintenance Items” section in the back of this guide for more information.8 Not all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual f or details.
_ Fr
ont differential oil
_ Fu
el lines and connections, fuel tank band
and fuel tank vapor vent system hoses
_ Fu
el tank cap gasket
_Ra
diator and condenser
_Re
ar differential oil
_St
eering gear
_St
eering linkage and boots
_Tr
ansfer case oil
Replace engine air filter
Replace engine oil and oil filter2
Replace spark plugs5
Rotate tires
18-TCS-11469_Toyota_WMG_MY19_Tundra_FFV_GUTS_3_0_tw .indd 537/5/18 10:26 PM
Page 57 of 66

56Maintenance Log
MAINTENANCE
EXPLANATION OF MAINTENANCE ITEMS
Engine Oil and Oil Filter
Replace the oil filter and drain and refill
the engine oil at specified intervals. For
recommended oil grade and viscosity,
refer to the Owner’s Manual. When using
E85 fuel, your engine oil and oil filter may
need to replaced more often. If using E85
fuel more than 50% of the time, change the
engine oil and oil filter every 2,500 miles
or three months. If using E85 fuel less than
50% of the time, follow the normal engine oil
and oil filter change schedule (5,000 miles
or six months). Reset the oil replacement
reminder light (MAINT REQD) or the message
OIL MAINTENANCE REQUIRED on the
multi-information display after engine oil
replacement at every 2,500- or 5,000-mile
interval (as applicable).
Exhaust Pipes and Mountings
Visually inspect the exhaust pipes, muffler
and hangers for cracks, deterioration and
damage. Start the engine and listen
carefully for any exhaust gas leakage.
Tighten connections or replace parts
as necessary.
Front and Rear Differential Oil
Inspect or replace at specified intervals.
When performing inspections, check each
component for signs of leakage. If you
discover any leakage, have it repaired by
a qualified technician immediately.
Fuel Lines and Connections,
Fuel Tank Band and Fuel Tank
Vapor Vent System Hoses
Visually inspect for corrosion, damage,
cracks, and loose or leaking connections.
Tighten connections or replace parts
as necessary.
Fuel Tank Cap Gasket
Visually inspect for cracks, deterioration
and damage and replace if necessary.
Nuts and Bolts on Chassis
and Body
Retighten the seat-mounting bolts and
front /rear suspension member retaining
bolts to specified torque.
Propeller Shaft
Re-torque the propeller shaft bolt. Only
a qualified technician should perform
this operation.
Radiator and Condenser
Inspect for debris, corrosion and signs
of damage. Have any problem repaired
immediately by a qualified technician.
Spark Plugs
Replace at specified intervals. Install new
plugs of the same type as originally
equipped. A qualified technician should
perform this operation.
18-TCS-11469_Toyota_WMG_MY19_Tundra_FFV_GUTS_3_0_tw .indd 567/5/18 10:27 PM