ESP TOYOTA xA 2005 Accessories, Audio & Navigation (in English)

OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS MONITOR’S LED stops flashing.

The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.

Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.

NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGER MEMORY was activated; an ALARM was
T
RIGGERED while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS REMOTE DISARMED
Page 14 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 7
SCION
SECURITY
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
THE
DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed spe -
cifically for this task, the G
LASS BREAKAGE SENSOR is capable of ignoring other noises, which helps
to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. A
RM the system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RM if any door or hatch is open.)
2. Wait until the S
TATUS MONIT OR’S LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. With the tip of a key, tap the center of the driver’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARN AWAY ALARM should be TRIGGERED. If the ALARM is not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Scion dealer for more information.

4. D
ISARM the system to stop the WARN AWAY ALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARM the system.
SCION
SECURITY
123
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
123
123
123
123
123
123123123

OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS MONITOR’S LED stops flashing.

The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.

Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*

This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.

NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGER MEMORY was activated; an ALARM was
T
RIGGERED while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS REMOTE DISARMED
Page 14 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 7
SCION
SECURITY
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
THE
DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed spe -
cifically for this task, the G
LASS BREAKAGE SENSOR is capable of ignoring other noises, which helps
to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. A
RM the system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RM if any door or hatch is open.)
2. Wait until the S
TATUS MONIT OR’S LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. With the tip of a key, tap the center of the driver’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARN AWAY ALARM should be TRIGGERED. If the ALARM is not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Scion dealer for more information.

4. D
ISARM the system to stop the WARN AWAY ALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARM the system.
SCION
SECURITY
123
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
123
123
123
123
123
123123123