trunk release TOYOTA xA 2005 Accessories, Audio & Navigation (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2005, Model line: xA, Model: TOYOTA xA 2005Pages: 23, PDF Size: 1.07 MB
Page 5 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 17
BRIEF DESCRIPTION–RS3200 FEATURES
a. Press and
release both
LOCK and
UNLOCK
buttons at the
same time.b. Press and
release the
UNLOCK button
once for all
doors unlock.or Press and
release the
LOCK button
once for driver’s
door unlock.
e. Open the driver’s
door; program-
ming is now
complete.i. The tail and marker lights flash 1 time, the
buzzer chirps 1 time, and the doors lock and
unlock 1 time.
The RS3200 will arm 30 seconds after the LOCK button on the remote
control is pressed, and DISARM when the UNLOCK button is pressed.
When the LOCK button is pressed, all the vehicle’s doors lock. When the
UNLOCK button is pressed, the driver’s door unlocks*, but if the UNLOCK
button is pressed again within 3 seconds, the remaining doors unlock.
The RS3200 will automatically RELOCK the vehicle’s doors if no door is
opened within 30 seconds after REMOTE DISARMING, the will REARM
30 seconds later.
The RS3200 will arm 30 seconds after you close and lock the vehicle’s
doors with the key, and will DISARM when you unlock a door with the key.
The RS3200 may be programmed to automatically arm 30 seconds after
the ignition key is removed, the vehicle exited and the last door and the
trunk are closed, without the necessity of locking the doors.
The RS3200 may be DISARMED with the vehicle’s ignition key after it
was PASSIVELY ARMED.
When the RS3200 has been PASSIVELY ARMED, and ENTRY DELAY
(user-selectable at 0,15, or 30 seconds) will start when a door is opened
before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a door is open)
the RS3200 will rm 30 seconds after you close all the doors and the hatch
(if open).
The RS3200 may be DISARMED by inserting the key into the ignition
switch and turning it to “ON”.
Forcibly unlocking or opening a door or hatch while the RS3200 is
ARMED will TRIGGER and ALARM immediately**. ( If the system was
PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is
TRIGGERED).
The RS3200 utilizes a microphone (usually mounted in the STATUS
MONITOR) to sense the noise from tapping on window glass, or glass
breaking, and TRIGGER an ALARM. It is fine tuned to “listen” for this type
of noise, and ignore other sounds.
When the GLASS BREAKAGE SENSOR’S microphone picks up tapping
or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the
headlights and tail and marker lights flash, and the horn sounds for 20
seconds, but the starter is not disabled. If there is another detection of
glass tapping or breaking, or if a door is opened or unlocked without a
key, the regular ALARM is TRIGGERED.
While ARMED, the RS3200 monitors the ignition switch. If an attempt is
made to start the vehicle without a key, an ALARM is triggered.
REMOTE ARMING
/ DISARMING
& LOCKING /
UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING / DISARMING
PASSIVE
(AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
GLASS BREAKAGE
SENSOR
WARN AWAY ALARM
IGNITION SWITCH
FEATURES FUNCTIONS
* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
** The alarm will not trigger if the passenger side door is forcibly unlocked, until the passenger door is
opened.
Page 7 of 23
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE
A
RMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
* The system will not A
RM while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 15
SCION
SECURITY
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS(PRE-ARM-ING)THEN FLASHES(SYSTEM IS ARMED)ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times. b.
Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = P
ASSIVE ARMING OFF
3 times = P
ASSIVE ARMING ON,
0 Sec. E
NTRY DEL AY
4 times = PASSIVE ARMING ON,
15 Sec. E
NTRY DEL AY
5 times = PASSIVE ARMING ON,
30 Sec. E
NTRY DEL AY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete.
e.
Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED
123123123
123
123
123
123
123
123
Page 10 of 23
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 is DISARMED at the same time.
However, if you do not open a door within 30 seconds, the system will relock the doors and the
RS3200 will R
EARM 30 seconds later.
0
15
30
45
Page 12 SCION RS3200 REMOTE KEYLESS Security systemSCION
RS3200 remote keyless Security system Page 9
THE DOORS ARE UNLOCKED BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL...
WHEN NO DOOR OR HATCH IS OPENED...FOR MORE THAN 30 SECONDS...THE RS3200 AUTOMATICALLY RELOCKS THE DOORS, THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP FOR 30 SECONDS
(PRE-ARM), THEN FLASHES WHEN THE SYSTEM IS ARMED
ALARM INFORMATION
ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
Forcibly opening a door or hatch without a key.
Opening the passenger side door or hatch with a key, while armed,
will trigger the alarm.
Pulling the trunk or hatch release lever inside the vehicle will
also T
RIGGER an ALARM.
Manually unlocking a door
Manually operating an inside lock button will T
RIGGER an ALARM.
Note: Because this action will T
RIGGER an ALARM, it is
important that you do not A
RM the system while
someone is in the vehicle.
“Hot wiring” the vehicle
The RS3200 can detect the absence of the ignition key if the
ignition circuit is shorted in attempt to start the vehicle.
Tapping on or breaking the glass
The noise from tapping on, or breaking of glass T
RIGGERS a WARN
A
WAY ALARM first, then a regular ALARM. See the description of
how the G
LASS BREAKAGE SENSOR TRIGGERS ALARMS on page 14.
Power restoration
I f power to the system is interrupted while it is A
RMED, an ALARM will
be T
RIGGERED immediately when power is restored.
123
123
123
123
123
SCION
SECURITY
Page 11 of 23
ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by press-
ing the PANIC button on the back of the remote control. Unless you D
ISARM the PANIC ALARM by
one of the described methods, it will continue for 60 seconds, then stop.
To activate the P
ANIC ALARM:
Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANIC ALARM at any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARM TRIGGER during the PANIC ALARM, the
regular A
LARM takes over. See ALARM INFORMATION on pages 12 and 13 for additional informa -
tion.
P ANIC
Page 10 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 11
MISCELLANEOUS
DOOR AJAR WARNING
The RS3200 will sound a five second DOOR AJAR WARNING when you attempt to REMOTE ARM the
system while a door is open. To stop the warning tone, either close the open door, or press and
release the UNLOCK button on the remote control. To A
RM the system, press the LOCK button
again.
Note: The D
OOR AJAR WARNING will not sound when the hatch is open; the doors will lock,
but the system will not A
RM until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicle’s doors when you turn the ignition
key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. If
you start the vehicle while a door is open, the system will not lock the doors; you must lock them
manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the system’s programming. Refer to page 18 for pro -
gramming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200’s remote controls is 50 feet. However, several factors that may
affect your remote control’s actual performance, include, but are not limited to:
The remote control’s battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the system’s antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROL’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS CLOSED, TURN THE KEY TO THE “ON” OR “LOCK”
POSITION...
ALL THE DOORS ARE LOCKED AUTOMATICALLY.WHEN THE KEY IS TURNED BACK TO THE “ACC” OR
“LOCK” POSITION...
ALL THE DOORS ARE UNLOCKED.
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH FOR 60 SECONDS
MARKER LIGHTS FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS123
123
123
123
123
123
123
123
123
123
PRESS THE LOCK BUTTON ON THE REMOTE CONTROL,OR...
PRESS THE PANIC BUTTON AGAIN, OR...
PRESS THE UNLOCK BUTTON ON THE REMOTE CONTROL, OR...
LOCK THE DOORS WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK
WITH THE KEY
Page 12 of 23
ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by press-
ing the PANIC button on the back of the remote control. Unless you D
ISARM the PANIC ALARM by
one of the described methods, it will continue for 60 seconds, then stop.
To activate the P
ANIC ALARM:
Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANIC ALARM at any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARM TRIGGER during the PANIC ALARM, the
regular A
LARM takes over. See ALARM INFORMATION on pages 12 and 13 for additional informa -
tion.
P ANIC
Page 10 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 11
MISCELLANEOUS
DOOR AJAR WARNING
The RS3200 will sound a five second DOOR AJAR WARNING when you attempt to REMOTE ARM the
system while a door is open. To stop the warning tone, either close the open door, or press and
release the UNLOCK button on the remote control. To A
RM the system, press the LOCK button
again.
Note: The D
OOR AJAR WARNING will not sound when the hatch is open; the doors will lock,
but the system will not A
RM until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicle’s doors when you turn the ignition
key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. If
you start the vehicle while a door is open, the system will not lock the doors; you must lock them
manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the system’s programming. Refer to page 18 for pro -
gramming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200’s remote controls is 50 feet. However, several factors that may
affect your remote control’s actual performance, include, but are not limited to:
The remote control’s battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the system’s antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROL’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS CLOSED, TURN THE KEY TO THE “ON” OR “LOCK”
POSITION...
ALL THE DOORS ARE LOCKED AUTOMATICALLY.WHEN THE KEY IS TURNED BACK TO THE “ACC” OR
“LOCK” POSITION...
ALL THE DOORS ARE UNLOCKED.
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH FOR 60 SECONDS
MARKER LIGHTS FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS123
123
123
123
123
123
123
123
123
123
PRESS THE LOCK BUTTON ON THE REMOTE CONTROL,OR...
PRESS THE PANIC BUTTON AGAIN, OR...
PRESS THE UNLOCK BUTTON ON THE REMOTE CONTROL, OR...
LOCK THE DOORS WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK
WITH THE KEY
Page 13 of 23
OPERATION
AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 is DISARMED at the same time.
However, if you do not open a door within 30 seconds, the system will relock the doors and the
RS3200 will R
EARM 30 seconds later.
0
15
30
45
Page 12 SCION RS3200 REMOTE KEYLESS Security systemSCION
RS3200 remote keyless Security system Page 9
THE DOORS ARE UNLOCKED BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL...
WHEN NO DOOR OR HATCH IS OPENED...FOR MORE THAN 30 SECONDS...THE RS3200 AUTOMATICALLY RELOCKS THE DOORS, THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP FOR 30 SECONDS
(PRE-ARM), THEN FLASHES WHEN THE SYSTEM IS ARMED
ALARM INFORMATION
ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
Forcibly opening a door or hatch without a key.
Opening the passenger side door or hatch with a key, while armed,
will trigger the alarm.
Pulling the trunk or hatch release lever inside the vehicle will
also T
RIGGER an ALARM.
Manually unlocking a door
Manually operating an inside lock button will T
RIGGER an ALARM.
Note: Because this action will T
RIGGER an ALARM, it is
important that you do not A
RM the system while
someone is in the vehicle.
“Hot wiring” the vehicle
The RS3200 can detect the absence of the ignition key if the
ignition circuit is shorted in attempt to start the vehicle.
Tapping on or breaking the glass
The noise from tapping on, or breaking of glass T
RIGGERS a WARN
A
WAY ALARM first, then a regular ALARM. See the description of
how the G
LASS BREAKAGE SENSOR TRIGGERS ALARMS on page 14.
Power restoration
I f power to the system is interrupted while it is A
RMED, an ALARM will
be T
RIGGERED immediately when power is restored.
123
123
123
123
123
SCION
SECURITY
Page 16 of 23
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE
A
RMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
* The system will not A
RM while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 15
SCION
SECURITY
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS(PRE-ARM-ING)THEN FLASHES(SYSTEM IS ARMED)ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times. b.
Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = P
ASSIVE ARMING OFF
3 times = P
ASSIVE ARMING ON,
0 Sec. E
NTRY DEL AY
4 times = PASSIVE ARMING ON,
15 Sec. E
NTRY DEL AY
5 times = PASSIVE ARMING ON,
30 Sec. E
NTRY DEL AY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete.
e.
Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED
123123123
123
123
123
123
123
123
Page 18 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 17
BRIEF DESCRIPTION–RS3200 FEATURES
a. Press and
release both
LOCK and
UNLOCK
buttons at the
same time.b. Press and
release the
UNLOCK button
once for all
doors unlock.or Press and
release the
LOCK button
once for driver’s
door unlock.
e. Open the driver’s
door; program-
ming is now
complete.i. The tail and marker lights flash 1 time, the
buzzer chirps 1 time, and the doors lock and
unlock 1 time.
The RS3200 will arm 30 seconds after the LOCK button on the remote
control is pressed, and DISARM when the UNLOCK button is pressed.
When the LOCK button is pressed, all the vehicle’s doors lock. When the
UNLOCK button is pressed, the driver’s door unlocks*, but if the UNLOCK
button is pressed again within 3 seconds, the remaining doors unlock.
The RS3200 will automatically RELOCK the vehicle’s doors if no door is
opened within 30 seconds after REMOTE DISARMING, the will REARM
30 seconds later.
The RS3200 will arm 30 seconds after you close and lock the vehicle’s
doors with the key, and will DISARM when you unlock a door with the key.
The RS3200 may be programmed to automatically arm 30 seconds after
the ignition key is removed, the vehicle exited and the last door and the
trunk are closed, without the necessity of locking the doors.
The RS3200 may be DISARMED with the vehicle’s ignition key after it
was PASSIVELY ARMED.
When the RS3200 has been PASSIVELY ARMED, and ENTRY DELAY
(user-selectable at 0,15, or 30 seconds) will start when a door is opened
before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a door is open)
the RS3200 will rm 30 seconds after you close all the doors and the hatch
(if open).
The RS3200 may be DISARMED by inserting the key into the ignition
switch and turning it to “ON”.
Forcibly unlocking or opening a door or hatch while the RS3200 is
ARMED will TRIGGER and ALARM immediately**. ( If the system was
PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is
TRIGGERED).
The RS3200 utilizes a microphone (usually mounted in the STATUS
MONITOR) to sense the noise from tapping on window glass, or glass
breaking, and TRIGGER an ALARM. It is fine tuned to “listen” for this type
of noise, and ignore other sounds.
When the GLASS BREAKAGE SENSOR’S microphone picks up tapping
or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the
headlights and tail and marker lights flash, and the horn sounds for 20
seconds, but the starter is not disabled. If there is another detection of
glass tapping or breaking, or if a door is opened or unlocked without a
key, the regular ALARM is TRIGGERED.
While ARMED, the RS3200 monitors the ignition switch. If an attempt is
made to start the vehicle without a key, an ALARM is triggered.
REMOTE ARMING
/ DISARMING
& LOCKING /
UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING / DISARMING
PASSIVE
(AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
GLASS BREAKAGE
SENSOR
WARN AWAY ALARM
IGNITION SWITCH
FEATURES FUNCTIONS
* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
** The alarm will not trigger if the passenger side door is forcibly unlocked, until the passenger door is
opened.