window TOYOTA xA 2005 Accessories, Audio & Navigation (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2005, Model line: xA, Model: TOYOTA xA 2005Pages: 23, PDF Size: 1.07 MB
Page 3 of 23
INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security system to protect your
vehicle! To get the most from the system, we strongly recommend that you read this Owner’s Guide
completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to A
RM and
D
ISARM at the same time you remotely lock and unlock the doors. The system provides compre -
hensive security protection through point-of-entry monitoring, glass breakage detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGERED and sound an ALARM when a door
is forcibly unlocked or opened*, or when a window is tapped on or broken. During the A
LARM, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash. A l s o , the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS MONITOR for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) and the G
LASS
B
REAKAGE SENSOR’S microphone. In vehicles with an engine immobilizer, there is already a LED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED and a micro-
phone mounted in a separate location. If your vehicle falls into this category, remember to look at
that LED when the information refers to the S
TATUS MONITOR. If you do not know where the LED is
located, refer to your vehicle’s owner’s guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicle’s doors when you turn the key in the
ignition switch to the “ON” or “START” position, and unlock them when you turn the key back to the
“ACC” or “LOCK” position. You may disable this feature by reprogramming the system; refer to page
18 for programming information.
* When the system is P
ASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will
elapse when a door is opened before an A
LARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK DIFFERENT THAN THE ONE
ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS(PRE-ARMING)THEN STARTS FLASHING(SYSTEM IS ARMED)
Page 2 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 19
SCION
SECURITY
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail -
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
123123123
123123
123
123
Page 5 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 17
BRIEF DESCRIPTION–RS3200 FEATURES
a. Press and
release both
LOCK and
UNLOCK
buttons at the
same time.b. Press and
release the
UNLOCK button
once for all
doors unlock.or Press and
release the
LOCK button
once for driver’s
door unlock.
e. Open the driver’s
door; program-
ming is now
complete.i. The tail and marker lights flash 1 time, the
buzzer chirps 1 time, and the doors lock and
unlock 1 time.
The RS3200 will arm 30 seconds after the LOCK button on the remote
control is pressed, and DISARM when the UNLOCK button is pressed.
When the LOCK button is pressed, all the vehicle’s doors lock. When the
UNLOCK button is pressed, the driver’s door unlocks*, but if the UNLOCK
button is pressed again within 3 seconds, the remaining doors unlock.
The RS3200 will automatically RELOCK the vehicle’s doors if no door is
opened within 30 seconds after REMOTE DISARMING, the will REARM
30 seconds later.
The RS3200 will arm 30 seconds after you close and lock the vehicle’s
doors with the key, and will DISARM when you unlock a door with the key.
The RS3200 may be programmed to automatically arm 30 seconds after
the ignition key is removed, the vehicle exited and the last door and the
trunk are closed, without the necessity of locking the doors.
The RS3200 may be DISARMED with the vehicle’s ignition key after it
was PASSIVELY ARMED.
When the RS3200 has been PASSIVELY ARMED, and ENTRY DELAY
(user-selectable at 0,15, or 30 seconds) will start when a door is opened
before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a door is open)
the RS3200 will rm 30 seconds after you close all the doors and the hatch
(if open).
The RS3200 may be DISARMED by inserting the key into the ignition
switch and turning it to “ON”.
Forcibly unlocking or opening a door or hatch while the RS3200 is
ARMED will TRIGGER and ALARM immediately**. ( If the system was
PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is
TRIGGERED).
The RS3200 utilizes a microphone (usually mounted in the STATUS
MONITOR) to sense the noise from tapping on window glass, or glass
breaking, and TRIGGER an ALARM. It is fine tuned to “listen” for this type
of noise, and ignore other sounds.
When the GLASS BREAKAGE SENSOR’S microphone picks up tapping
or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the
headlights and tail and marker lights flash, and the horn sounds for 20
seconds, but the starter is not disabled. If there is another detection of
glass tapping or breaking, or if a door is opened or unlocked without a
key, the regular ALARM is TRIGGERED.
While ARMED, the RS3200 monitors the ignition switch. If an attempt is
made to start the vehicle without a key, an ALARM is triggered.
REMOTE ARMING
/ DISARMING
& LOCKING /
UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING / DISARMING
PASSIVE
(AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
GLASS BREAKAGE
SENSOR
WARN AWAY ALARM
IGNITION SWITCH
FEATURES FUNCTIONS
* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
** The alarm will not trigger if the passenger side door is forcibly unlocked, until the passenger door is
opened.
Page 8 of 23
OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*
In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS MONITOR’S LED stops flashing.
The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGER MEMORY was activated; an ALARM was
T
RIGGERED while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS REMOTE DISARMED
Page 14 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 7
SCION
SECURITY
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
THE
DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed spe -
cifically for this task, the G
LASS BREAKAGE SENSOR is capable of ignoring other noises, which helps
to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. A
RM the system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RM if any door or hatch is open.)
2. Wait until the S
TATUS MONIT OR’S LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. With the tip of a key, tap the center of the driver’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARN AWAY ALARM should be TRIGGERED. If the ALARM is not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Scion dealer for more information.
4. D
ISARM the system to stop the WARN AWAY ALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARM the system.
SCION
SECURITY
123
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
123
123
123
123
123
123123123
Page 15 of 23
OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key:
Insert the key into the driver’s door key switch and turn it toward the
rear of the vehicle:
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*
In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARM will be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously:
The driver’s door unlocks.
The vehicle’s tail and marker lights flash twice.
The interior lights turn on for 30 seconds.
The S
TATUS MONITOR’S LED stops flashing.
The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the
driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.
The S
TATUS MONITOR’S LED stops flashing. The system
is now D
ISARMED.*
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGER MEMORY was activated; an ALARM was
T
RIGGERED while you were away from the vehicle.
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE-RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS REMOTE DISARMED
Page 14 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 7
SCION
SECURITY
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO “ON” TO DISARM THE SYSTEM
THE
DRIVER’S DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS FLASHING WHEN THE SYSTEM IS DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed spe -
cifically for this task, the G
LASS BREAKAGE SENSOR is capable of ignoring other noises, which helps
to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. A
RM the system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not A
RM if any door or hatch is open.)
2. Wait until the S
TATUS MONIT OR’S LED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. With the tip of a key, tap the center of the driver’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARN AWAY ALARM should be TRIGGERED. If the ALARM is not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Scion dealer for more information.
4. D
ISARM the system to stop the WARN AWAY ALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARM the system.
SCION
SECURITY
123
You must disarm the system before opening the hatch, or else the Alarm will
be triggered.
123
123
123
123
123
123123123
Page 18 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 17
BRIEF DESCRIPTION–RS3200 FEATURES
a. Press and
release both
LOCK and
UNLOCK
buttons at the
same time.b. Press and
release the
UNLOCK button
once for all
doors unlock.or Press and
release the
LOCK button
once for driver’s
door unlock.
e. Open the driver’s
door; program-
ming is now
complete.i. The tail and marker lights flash 1 time, the
buzzer chirps 1 time, and the doors lock and
unlock 1 time.
The RS3200 will arm 30 seconds after the LOCK button on the remote
control is pressed, and DISARM when the UNLOCK button is pressed.
When the LOCK button is pressed, all the vehicle’s doors lock. When the
UNLOCK button is pressed, the driver’s door unlocks*, but if the UNLOCK
button is pressed again within 3 seconds, the remaining doors unlock.
The RS3200 will automatically RELOCK the vehicle’s doors if no door is
opened within 30 seconds after REMOTE DISARMING, the will REARM
30 seconds later.
The RS3200 will arm 30 seconds after you close and lock the vehicle’s
doors with the key, and will DISARM when you unlock a door with the key.
The RS3200 may be programmed to automatically arm 30 seconds after
the ignition key is removed, the vehicle exited and the last door and the
trunk are closed, without the necessity of locking the doors.
The RS3200 may be DISARMED with the vehicle’s ignition key after it
was PASSIVELY ARMED.
When the RS3200 has been PASSIVELY ARMED, and ENTRY DELAY
(user-selectable at 0,15, or 30 seconds) will start when a door is opened
before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a door is open)
the RS3200 will rm 30 seconds after you close all the doors and the hatch
(if open).
The RS3200 may be DISARMED by inserting the key into the ignition
switch and turning it to “ON”.
Forcibly unlocking or opening a door or hatch while the RS3200 is
ARMED will TRIGGER and ALARM immediately**. ( If the system was
PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is
TRIGGERED).
The RS3200 utilizes a microphone (usually mounted in the STATUS
MONITOR) to sense the noise from tapping on window glass, or glass
breaking, and TRIGGER an ALARM. It is fine tuned to “listen” for this type
of noise, and ignore other sounds.
When the GLASS BREAKAGE SENSOR’S microphone picks up tapping
or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the
headlights and tail and marker lights flash, and the horn sounds for 20
seconds, but the starter is not disabled. If there is another detection of
glass tapping or breaking, or if a door is opened or unlocked without a
key, the regular ALARM is TRIGGERED.
While ARMED, the RS3200 monitors the ignition switch. If an attempt is
made to start the vehicle without a key, an ALARM is triggered.
REMOTE ARMING
/ DISARMING
& LOCKING /
UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING / DISARMING
PASSIVE
(AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
GLASS BREAKAGE
SENSOR
WARN AWAY ALARM
IGNITION SWITCH
FEATURES FUNCTIONS
* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
** The alarm will not trigger if the passenger side door is forcibly unlocked, until the passenger door is
opened.
Page 20 of 23
INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security system to protect your
vehicle! To get the most from the system, we strongly recommend that you read this Owner’s Guide
completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to A
RM and
D
ISARM at the same time you remotely lock and unlock the doors. The system provides compre -
hensive security protection through point-of-entry monitoring, glass breakage detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGERED and sound an ALARM when a door
is forcibly unlocked or opened*, or when a window is tapped on or broken. During the A
LARM, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash. A l s o , the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS MONITOR for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) and the G
LASS
B
REAKAGE SENSOR’S microphone. In vehicles with an engine immobilizer, there is already a LED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED and a micro-
phone mounted in a separate location. If your vehicle falls into this category, remember to look at
that LED when the information refers to the S
TATUS MONITOR. If you do not know where the LED is
located, refer to your vehicle’s owner’s guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicle’s doors when you turn the key in the
ignition switch to the “ON” or “START” position, and unlock them when you turn the key back to the
“ACC” or “LOCK” position. You may disable this feature by reprogramming the system; refer to page
18 for programming information.
* When the system is P
ASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will
elapse when a door is opened before an A
LARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK DIFFERENT THAN THE ONE
ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS(PRE-ARMING)THEN STARTS FLASHING(SYSTEM IS ARMED)
Page 2 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 19
SCION
SECURITY
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail -
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
123123123
123123
123
123