engine TOYOTA xA 2006 Accessories, Audio & Navigation (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2006, Model line: xA, Model: TOYOTA xA 2006Pages: 23, PDF Size: 2.8 MB
Page 3 of 23
INTRODUCTIONCongratulations on your choice of the xA remote keyless security system to protect your vehicle! To
get the most from the system, we strongly recommend that you read this Owner’s Guide completely
to learn all of its features and functions.
The xA Security with RKE provides the convenience of remote keyless operation, enabling you to
ARM
and D
ISARM
at the same time you remotely lock and unlock the doors. The system provides
comprehensive security protection through point-of-entry monitoring, intrusion detection and ignition
switch monitoring. While A
RMED
, the system will be T
RIGGERED
and sound an A
LARM
when a door is
forcibly unlocked or opened*, or when movement occurs inside the vehicle. During the A
LARM
, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.Also, the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS
MONITOR
for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) .
About the ignition-controlled automatic door locking/unlocking function.
The xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the key in the ignition switch to the “ON” or “START” position, and unlock them when you turn the
key back to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the sys-
tem; refer to page 18 for programming information.
*When the system is P
ASSIVELY
(AUTOMATICALLY
) A
RMED
, there is an E
NTRY
DELAY
that will
elapse when a door is opened before an A
LARM
is T
RIGGERED
.
LIGHTS FOR30 SECONDS(PRE-ARMING
)
THEN STARTS
FLASHING(SYSTEM IS
ARMED
)
Page 2
SCION
SCION
Page 19
SCIONSECURITY
REMOTE CONTROL BATTERY REPLACEMENTThe following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail-
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5.Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
SECURITY
1
2
1
2
Page 6 of 23
PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTIONThe xA Security with RKE is factory-set to unlock the driver’s door when the UNLOCK button is
pressed on the remote control, then unlock the remaining doors when the UNLOCK button is
pressed again within 3 seconds. You may change the programming so all doors will unlock at once
when the UNLOCK button is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.Page 16
SCION
SCION
Page 5
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Insertthe key into,
and removeit
from the ignition
switch 2 times.e. Insertthe key into
the ignition and
leave it in.
c. Insertthe key
into, and remove
it from the ignition
switch 1 time.g. Turnthe key from
LOCK to ON 4
times(ending at
LOCK.)h. Removethe key
from the ignition
switch.
i.The tail and marker lights flash 4times, the
buzzer chirps 4 times, and the doors lock
and unlock 4 times.
b. Close,then open
the driver’s door
2 times.f. Closethe driver’s
door.
d. Close, then open
the driver’s door
2 times.
When an alarm is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (DISARMED).
During an alarm, the system will lock the doors if one is unlocked and
will continue to do so for the duration of the alarm.
The user is notified that an alarm occurred. Upon DISARMING the sys-
tem after an alarm was TRIGGERED, the vehicle’s tail and marker lights
will be turned on, and the BUZZER sounds for 2 seconds.
You may TRIGGER a PANIC ALARM by pressing the PANIC button on
the back of the remote control to draw attention to your vehicle. During
the PANIC ALARM, the head, tail and marker lights flash, and the horn
sounds but the starter is not disabled.
The xA Security with RKE flashes the vehicle’s tail and marker lights
during REMOTE ARMING and REMOTE DISARMING, as well as during
an alarm. Also, the headlights flash during an alarm.
When the system is REMOTE DISARMED, it turns on the interior lights
in the vehicle for 30 seconds, or until the key is inserted into the ignition
switch. It also turns them on during an alarm.
During an alarm, the xA Security with RKE activates the vehicle’s horn.
If power tot the xA Security with RKE is disrupted while it is ARMED, an
alarm is TRIGGERED once power is restored.
This panel houses the flashing LED that indicates the operating status
of the security system.
The xA Security with RKE utilizes a PIEZO BUZZER, usually mounted
in the engine compartment, to sounds confirmation “chirps” and tones
for function confirmation and programming step confirmation.
The xA Security with RKE automatically locks your vehicle’s doors when
you turn the ignition key to “ON” or “START”, and unlocks the doors
when you turn the key back to “ACC” or “LOCK”.
The buzzer sounds for 5 seconds when you attempt to REMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with the
xA Security with RKE is approximately 50 feet. Please refer to page 10
for a description of factors that may affect the performance (operating
range) of the remote controls. STARTER DISABLE
FORCED LOCK DURING ALARM
TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED AUTO-
MATIC DOOR LOCK / UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
FEATURES FUNCTIONS
Page 9 of 23
OPERATIONPASSIVE (AUTOMATIC) ARMING & DISARMINGWhen the xA Security with RKE is programmed to P
ASSIVELY
ARM, the system will A
RM
after the
ignition key is removed and all doors are closed; you do not need to lock the doors. When you come
back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to
“ON” during the E
NTRY
DELAY
(0, 15 or 30 seconds), or an A
LARM
will be T
RIGGERED
. If you lock the
doors, regular A
RMING
will override P
ASSIVE
ARMING
; there will be no E
NTRY
DELAY
. See the PRO-
GRAMMING section on page 15 to activate the P
ASSIVE
ARMING
mode, as well as select the E
NTRY
DELAY
time.
To P
ASSIVELY
ARM
the system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (The system will not
A
RM
while any of the doors are open.)
Close the hatch, if necessary. (The system will not A
RM
while
the hatch is open.)
After the last door or hatch is closed:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds,
then starts flashing. The system is now A
RMED
.
To D
ISARM
the P
ASSIVELY
ARMED
system:
Enter the vehicle through a front door.
The E
NTRY
DELAY
begins:
The STATUS
MONITOR
’SLED turns on (no flashing.)
Insert the key into the ignition switch and turn it to
“ON”
before the E
NTRY
DELAY
ends.*
The LED turns off. The system is now D
ISARMED
.
You may also D
ISARM
the system following any of the methods
described on page 7.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED
, the T
RIGGER
MEMORY
was activated; an A
LARM
was
T
RIGGERED
while you were away from the vehicle.
*If the E
NTRY
DELAY
time elapses before the ignition switch is turned to “ON”, an A
LARM
will
be T
RIGGERED
. To D
ISARM
the system during an A
LARM
, insert the ignition key and turn it to
“ON”, or press and release the remote control’s UNLOCK button.
Page 8
SCION
SCION
Page 13
THE SYSTEM ARMS
30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR OR HATCH
)
IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT
TO
“ON”
SCIONSECURITY
LIGHTS FOR30 SECONDS(PRE-ARM
-
ING)THEN
STARTS
FLASHING(SYSTEM IS
ARMED
)
SCIONSECURITY
TURNS ON(NO
FLASHING
)
DURING THE
ENTRY
DELAY
ALARM INFORMATIONALARM DESCRIPTIONSRegular
ALARM
When an A
LARM
is triggered in any way other than initial detection by the R
ADAR
SENSOR
,the following
occur:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
The starter is disabled (no engine start) until the system is D
ISARMED
.
The door lock will be relocked if someone reaches in and unlocks the inside lock button. After
60 seconds of A
LARM
, the system will R
EARM
and continue to protect the vehicle.
STOPPING AN ALARMSimply D
ISARM
the system using the remote control or key as described on page 7.
THE HORN SOUNDS
FOR
60 SECONDS
HEADLIGHTS FLASH
FOR
60 SECONDS
THE STARTER IS DISABLED UNTIL
THE SYSTEM IS DISARMED
MARKER LIGHTS FLASH
FOR
60 SECONDSTAIL LIGHTS FLASH
FOR
60 SECONDS INTERIOR LIGHTS TURN ON FOR
60 SECONDS
1
2
2
1
1
Page 14 of 23
OPERATIONPASSIVE (AUTOMATIC) ARMING & DISARMINGWhen the xA Security with RKE is programmed to P
ASSIVELY
ARM, the system will A
RM
after the
ignition key is removed and all doors are closed; you do not need to lock the doors. When you come
back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to
“ON” during the E
NTRY
DELAY
(0, 15 or 30 seconds), or an A
LARM
will be T
RIGGERED
. If you lock the
doors, regular A
RMING
will override P
ASSIVE
ARMING
; there will be no E
NTRY
DELAY
. See the PRO-
GRAMMING section on page 15 to activate the P
ASSIVE
ARMING
mode, as well as select the E
NTRY
DELAY
time.
To P
ASSIVELY
ARM
the system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (The system will not
A
RM
while any of the doors are open.)
Close the hatch, if necessary. (The system will not A
RM
while
the hatch is open.)
After the last door or hatch is closed:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds,
then starts flashing. The system is now A
RMED
.
To D
ISARM
the P
ASSIVELY
ARMED
system:
Enter the vehicle through a front door.
The E
NTRY
DELAY
begins:
The STATUS
MONITOR
’SLED turns on (no flashing.)
Insert the key into the ignition switch and turn it to
“ON”
before the E
NTRY
DELAY
ends.*
The LED turns off. The system is now D
ISARMED
.
You may also D
ISARM
the system following any of the methods
described on page 7.
NOTE: If your vehicle’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED
, the T
RIGGER
MEMORY
was activated; an A
LARM
was
T
RIGGERED
while you were away from the vehicle.
*If the E
NTRY
DELAY
time elapses before the ignition switch is turned to “ON”, an A
LARM
will
be T
RIGGERED
. To D
ISARM
the system during an A
LARM
, insert the ignition key and turn it to
“ON”, or press and release the remote control’s UNLOCK button.
Page 8
SCION
SCION
Page 13
THE SYSTEM ARMS
30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR OR HATCH
)
IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT
TO
“ON”
SCIONSECURITY
LIGHTS FOR30 SECONDS(PRE-ARM
-
ING)THEN
STARTS
FLASHING(SYSTEM IS
ARMED
)
SCIONSECURITY
TURNS ON(NO
FLASHING
)
DURING THE
ENTRY
DELAY
ALARM INFORMATIONALARM DESCRIPTIONSRegular
ALARM
When an A
LARM
is triggered in any way other than initial detection by the R
ADAR
SENSOR
,the following
occur:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
The starter is disabled (no engine start) until the system is D
ISARMED
.
The door lock will be relocked if someone reaches in and unlocks the inside lock button. After
60 seconds of A
LARM
, the system will R
EARM
and continue to protect the vehicle.
STOPPING AN ALARMSimply D
ISARM
the system using the remote control or key as described on page 7.
THE HORN SOUNDS
FOR
60 SECONDS
HEADLIGHTS FLASH
FOR
60 SECONDS
THE STARTER IS DISABLED UNTIL
THE SYSTEM IS DISARMED
MARKER LIGHTS FLASH
FOR
60 SECONDSTAIL LIGHTS FLASH
FOR
60 SECONDS INTERIOR LIGHTS TURN ON FOR
60 SECONDS
1
2
2
1
1
Page 17 of 23
PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTIONThe xA Security with RKE is factory-set to unlock the driver’s door when the UNLOCK button is
pressed on the remote control, then unlock the remaining doors when the UNLOCK button is
pressed again within 3 seconds. You may change the programming so all doors will unlock at once
when the UNLOCK button is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.Page 16
SCION
SCION
Page 5
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Insertthe key into,
and removeit
from the ignition
switch 2 times.e. Insertthe key into
the ignition and
leave it in.
c. Insertthe key
into, and remove
it from the ignition
switch 1 time.g. Turnthe key from
LOCK to ON 4
times(ending at
LOCK.)h. Removethe key
from the ignition
switch.
i.The tail and marker lights flash 4times, the
buzzer chirps 4 times, and the doors lock
and unlock 4 times.
b. Close,then open
the driver’s door
2 times.f. Closethe driver’s
door.
d. Close, then open
the driver’s door
2 times.
When an alarm is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (DISARMED).
During an alarm, the system will lock the doors if one is unlocked and
will continue to do so for the duration of the alarm.
The user is notified that an alarm occurred. Upon DISARMING the sys-
tem after an alarm was TRIGGERED, the vehicle’s tail and marker lights
will be turned on, and the BUZZER sounds for 2 seconds.
You may TRIGGER a PANIC ALARM by pressing the PANIC button on
the back of the remote control to draw attention to your vehicle. During
the PANIC ALARM, the head, tail and marker lights flash, and the horn
sounds but the starter is not disabled.
The xA Security with RKE flashes the vehicle’s tail and marker lights
during REMOTE ARMING and REMOTE DISARMING, as well as during
an alarm. Also, the headlights flash during an alarm.
When the system is REMOTE DISARMED, it turns on the interior lights
in the vehicle for 30 seconds, or until the key is inserted into the ignition
switch. It also turns them on during an alarm.
During an alarm, the xA Security with RKE activates the vehicle’s horn.
If power tot the xA Security with RKE is disrupted while it is ARMED, an
alarm is TRIGGERED once power is restored.
This panel houses the flashing LED that indicates the operating status
of the security system.
The xA Security with RKE utilizes a PIEZO BUZZER, usually mounted
in the engine compartment, to sounds confirmation “chirps” and tones
for function confirmation and programming step confirmation.
The xA Security with RKE automatically locks your vehicle’s doors when
you turn the ignition key to “ON” or “START”, and unlocks the doors
when you turn the key back to “ACC” or “LOCK”.
The buzzer sounds for 5 seconds when you attempt to REMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with the
xA Security with RKE is approximately 50 feet. Please refer to page 10
for a description of factors that may affect the performance (operating
range) of the remote controls. STARTER DISABLE
FORCED LOCK DURING ALARM
TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED AUTO-
MATIC DOOR LOCK / UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
FEATURES FUNCTIONS
Page 20 of 23
INTRODUCTIONCongratulations on your choice of the xA remote keyless security system to protect your vehicle! To
get the most from the system, we strongly recommend that you read this Owner’s Guide completely
to learn all of its features and functions.
The xA Security with RKE provides the convenience of remote keyless operation, enabling you to
ARM
and D
ISARM
at the same time you remotely lock and unlock the doors. The system provides
comprehensive security protection through point-of-entry monitoring, intrusion detection and ignition
switch monitoring. While A
RMED
, the system will be T
RIGGERED
and sound an A
LARM
when a door is
forcibly unlocked or opened*, or when movement occurs inside the vehicle. During the A
LARM
, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.Also, the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS
MONITOR
for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) .
About the ignition-controlled automatic door locking/unlocking function.
The xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the key in the ignition switch to the “ON” or “START” position, and unlock them when you turn the
key back to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the sys-
tem; refer to page 18 for programming information.
*When the system is P
ASSIVELY
(AUTOMATICALLY
) A
RMED
, there is an E
NTRY
DELAY
that will
elapse when a door is opened before an A
LARM
is T
RIGGERED
.
LIGHTS FOR30 SECONDS(PRE-ARMING
)
THEN STARTS
FLASHING(SYSTEM IS
ARMED
)
Page 2
SCION
SCION
Page 19
SCIONSECURITY
REMOTE CONTROL BATTERY REPLACEMENTThe following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail-
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5.Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
SECURITY
1
2
1
2