start stop button TOYOTA YARIS 2012 User Guide

292 2-2. Instrument cluster
YARIS_F (including HV)_WE_52C79E
EV indicator customization (hybrid vehicle)
EV indicator can be activated or deactivated by
pressing the display change button when the EV
indicator customization display is displayed.
To change the EV indicator customization display,
display the odometer and press and hold the display
change button until the display changes.
When disconnecting and reconnecting battery (except hybrid vehicle)
or 12-volt battery (hybrid vehicle) terminals
The following information data will be reset:
Stop & Start system total operation time (if equipped)
Average fuel consumption
Driving range
Average vehicle speed
NOTICE
The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.

307 2-3. Operating the lights and wipers
2
When driving
YARIS_F (including HV)_WE_52C79E
Vehicles without a smart entry & start system
If the wiper switch is turned to the “AUTO” position while the engine
switch is in the “ON” position, the wiper will operate once to show that
“AUTO” mode is activated.
When the sensor sensitivity ring is turned toward high while in “AUTO”
mode, the wiper will operate once to indicate that the sensor sensitivity is
enhanced.
If the temperature of the raindrop sensor is 90C (194F) or higher, or
-15C (5F) or lower, automatic operation may not occur. In this case,
operate the wiper in any mode other than “AUTO”.
Vehicles with a smart entry & start system or a push-button start sys-
tem
Except hybrid vehicle: If the wiper switch is turned to the “AUTO” position
while the “ENGINE START STOP” switch is in IGNITION ON mode, the
wiper will operate once to show that “AUTO” mode is activated.
Hybrid vehicle: If the wiper switch is turned to the “AUTO” position while
the “POWER” switch is in ON mode, the wiper will operate once to show
that “AUTO” mode is activated.
When the sensor sensitivity ring is turned toward high while in “AUTO”
mode, the wiper will operate once to indicate that the sensor sensitivity is
enhanced.
If the temperature of the raindrop sensor is 90C (194F) or higher, or
-15C (5F) or lower, automatic operation may not occur. In this case,
operate the wiper in any mode other than “AUTO”.
If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the
windshield washer fluid reservoir.

428
3-5. Other interior features
YARIS_F (including HV)_WE_52C79E
Clock
The clock is displayed when
Except hybrid vehicle
Vehicles without a smart entry & start system:
The engine switch is in the “ON” position.
Vehicles with a smart entry & start system:
The “ENGINE START STOP” switch is in IGNITION ON mode.
Hybrid vehicle
Vehicles without an electronic key:
The engine switch is in the “ON” position.
Vehicles with an electronic key:
The “POWER” switch is in ON mode.
When disconnecting and reconnecting battery terminals
The clock data will be reset.
The clock can be adjusted by pressing the buttons.
Adjusts the hours
Adjusts the minutes

476 4-3. Do-it-yourself maintenance
YARIS_F (including HV)_WE_52C79E
Engine oil consumption
The amount of engine oil consumed depends on the oil viscosity, the
quality of the oil and the way the vehicle is driven.
More oil is consumed under driving conditions such as high speeds and
frequent acceleration and deceleration.
A new engine consumes more oil.
When judging the amount of oil consumption, keep in mind that the oil
may have become diluted, making it difficult to judge the true level accu-
rately.
Oil consumption: Max. 1.0 L/1000 km (1.1 qt./600 miles, 0.9 Imp. qt./600
miles)
If your vehicle consumes more than 1.0 L (1.1 qt., 0.9 Imp. qt.) every
1000 km (600 miles), contact any authorized Toyota dealer or repairer, or
another duly qualified and equipped professional.
After changing the engine oil (diesel engine only)
The engine oil maintenance data should be reset. Perform the following pro-
cedures:
Switch the display to the trip meter “A” when the engine is running.
(P. 287)
Vehicles without a smart entry & start system:
Turn the engine switch to the “LOCK” position.
Vehicles with a smart entry & start system:
Turn the “ENGINE START STOP” switch off.
Vehicles without a smart entry & start system:
While pressing the display change button (P. 287), turn the
engine switch to the “ON” position (do not start the engine because
reset mode will be canceled). Continue to press and hold the button
until the trip meter displays “000000”.
Vehicles with a smart entry & start system:
While pressing the display change button (P. 287), turn the
“ENGINE START STOP” switch to the IGNITION ON mode (do not
start the engine because otherwise the reset mode will be can-
celed). Continue to press and hold the button until the trip meter
displays “000000”.

528 4-3. Do-it-yourself maintenance
YARIS_F (including HV)_WE_52C79E
11 IG2 NO.2 10 ASmart entry & start system, push-
button start system, multiport fuel
injection system/sequential multi-
port fuel injection system, SRS air-
bag system, steering lock system,
stop lights
12 DOME 15 AAudio system, main body ECU,
personal lights, foot well lights
13 ECU-B NO.1 5 AMain body ECU, smart entry & start
system
14 METER 7.5 A Gauge and meters
15 IGN 15 AMultiport fuel injection system/
sequential multiport fuel injection
system
16 H-LP RH-HI 5 A Right-hand headlight (high beam)
17 H-LP LH-HI 5 ALeft-hand headlight (high beam),
gauge and meters
18 D/L NO.2 25 A
Power door lock
19 HAZ 10 A Emergency flashers
20 ETCS 10 AMultiport fuel injection system/
sequential multiport fuel injection
system
21 ABS NO.1 20 A Brake system
22 ENG W/PMP 30 AMultiport fuel injection system/
sequential multiport fuel injection
system
23 H-LP-MAIN 20 AH-LP LH-LO, H-LP RH-LO, H-LP
LH-HI, H-LP RH-HI
24 ABS MTR NO.1 30 A Brake system
25 P/I 50 A EFI-MAIN, HORN, IG2
FuseAmpereCircuit

5
575 5-2. Steps to take in an emergency
When trouble arises
YARIS_F (including HV)_WE_52C79E
Follow the correction procedures. (vehicles with a smart entry &
start system or push-button start system)
After taking the specified steps to correct the suspected problem,
check that the warning light goes off.
Interior
buzzerExterior
buzzerWarning
lightWarning light/DetailsCorrection
procedure
Continuous Continuous
(Flashes
in
yellow)Smart entry & start system
indicator light (vehicles
with a hybrid transmission
or a Multidrive)
Except hybrid vehicle
The electronic key was car-
ried outside the vehicle and
the driver’s door was
opened and closed while
any shift position other than
P was selected without turn-
ing off the “ENGINE START
STOP” switch.
Hybrid vehicle
The electronic key was car-
ried outside the vehicle and
the driver’s door was
opened and closed while
any shift position other than
P was selected without turn-
ing off the “POWER” switch.• Change the
shift position to
P.
• Bring the elec-
tronic key back
into the vehicle.

616
5-2. Steps to take in an emergency
YARIS_F (including HV)_WE_52C79E
If the shift lever cannot be shifted from P (vehicles with a hybrid transmission or a Multidrive)
If the shift lever cannot be shifted with your foot on the brake pedal,
there may be a problem with the shift lock system (a system to pre-
vent accidental operation of the shift lever). Have the vehicle
inspected by any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional immediately.
The following steps may be used as an emergency measure to
ensure that the shift lever can be shifted:
Set the parking brake.
Except hybrid vehicle
Vehicles without a smart entry & start system:
Turn the engine switch to the “ACC” position.
Vehicles with a smart entry & start system:
Turn the “ENGINE START STOP” switch to ACCESSORY
mode.
Hybrid vehicle
Vehicles without an electronic key:
Turn the engine switch to the “ACC” position.
Vehicles with an electronic key:
Turn the “POWER” switch to ACCESSORY mode.
Depress the brake pedal.
Press the shift lock override
button.
The shift lever can be shifted
while the button is pressed.

5
617
5-2. Steps to take in an emergency
When trouble arises
YARIS_F (including HV)_WE_52C79E
If the shift lever cannot be shifted (vehicles with a multi-mode manual transmission)
If the shift lever cannot be shifted with your foot on the brake pedal,
there may be a problem with the shift lock system (a system to pre-
vent accidental operation of the shift lever). Have the vehicle
inspected by any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional immediately.
The following steps may be used as an emergency measure to
ensure that the shift lever can be shifted:
Set the parking brake.
Vehicles without a smart entry & start system:
Turn the engine switch to the “ON” position.
Vehicles with a smart entry & start system:
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Depress the brake pedal.
Press the shift lock override
button with a flathead screw-
driver or equivalent.
The shift lever can be shifted
while the button is pressed.