maintenance reset TOYOTA YARIS 2019 Owners Manual (in English)

YARIS SEDAN_OM_OM99S50z_(U)
1252-7. Windows
2
Before Driving
To fully open the window automatically, press the switch completely
down, then release. The window will fully open automatically.
To fully close the window automatically, pull the switch comple tely up,
then release. The window will fully close automatically.
To stop the window partway, pull or press the switch in the opp osite
direction and then release it.
This function is only equi pped on the driver’s side.
Power window system initialization procedure
If the battery was disconnected during vehicle maintenance, or for other rea-
sons (such as a switch continues to be operated after the windo w is fully
open/closed), the window will not fully open and close automati cally.
The power window auto function will only resume on a power window that has
been reset.
Switch the ignition ON.
Make sure that the power window lock switch located on the driv er’s door
is not depressed.
Press the switch and fully open the window.
Pull up the switch to fully close the window and continue holdi ng the
switch for about 2 seconds after the window fully closed.
Make sure that the power windows operate correctly using the do or
switches.
If foreign matter is detected between the window and the window
frame while the window is closi ng automatically, the window sto ps
closing and automatic ally opens partway.
■Jam-safe window
●The jam-safe function may operate under the following condition s
• A strong impact is detected while the window is closing automa tically.
• Window is closing automatically in very low temperatures.
● In the event the jam-safe function activates and the power window cannot
be closed automatically, pull and hold the switch and the windo w will close.
● The jam-safe window function does not operate until the system has been
reset.
Auto-opening/closing
Jam-safe window
1
2
3
4
5

164
YARIS SEDAN_OM_OM99S50z_(U)
3-2. Combination Meter and Display
*1: The light turns on when the ignition is switched on for an operation check,
and turns off a few seconds later or when the engine is started . If the light
does not turn on or remains turned on, have the vehicle inspect ed at your
Toyota dealer.
When the ignition is switched ON,
the wrench indicato r light is illumi-
nated and then turns off after a
few seconds.
The wrench indicator light is illu-
minated when the preset mainte-
nance period arrives. Verify the
content and perform mainte-
nance.
Refer to Maintenance Monitor on
P. 434.
(Blue)
Low Engine Coolant
Temperature Indicator
Light ( P. 165)
(If equipped)
Cruise Main Indication
(P. 226)
(If equipped)
Shift Position Indication
(P. 171)(White/
Green)
(If equipped)
Cruise Set Indication/
Indicator Light ( P. 226)
Headlight High-Beam
Indicator Light
( P. 185, 185)
(If equipped)
Select Mode Indicator
Light ( P. 214)
Turn Signal/Hazard
Warning Indicator Lights
( P. 189, 197) Lights-On Indicator Light
(
P. 181)
*1Security Indicator Light
(P. 128)*1Front Passenger
Air Bag Deactiva-
tion Indicator
Light ( P. 78)
Wrench Indicator Light

434
YARIS SEDAN_OM_OM99S50z_(U)
5-2. Scheduled Maintenance
Maintenance Monitor
“Oil Change” with a flexible setting*1 is available. Consult your Toyota
dealer when you want t o change the setting
*2. Once the system turns
on, the wrench indica tor light in the combination meter will be illumi-
nated when remaining oil life becomes less than 300 miles (500 k m),
or remaining days are less th an 15 (whichever comes first).
*1: The flexible setting is available in the United States and Pue rto Rico.
Based on the engine operating conditions, the onboard computer in your
vehicle calculates the remaining oil life. Toyota Genuine Motor Oil 0W-20
or equivalent are required to achieve optimum calculation perfo rmance.
*2: Once the Flexible Oil Maintenance Setting is selected, the sys tem must be
reset whenever replacing the engine oil.
■
Reset method
Press and hold the selector with
the ignition switched off, then
switch it on. Keep pressing the
selector for more than 5 sec-
onds. The master warning light
will flash for a few seconds
when the reset is completed.
Select the icon on the home screen to display the “Applica-
tions” screen.
Select “Maintenance” to display the maintenance list screen.
Switch the tab and sel ect the setting item you want to change.
Maintenance Monitor (Type A audio)
Selector
Maintenance Monitor (Type B audio)
1
2
3

YARIS SEDAN_OM_OM99S50z_(U)
4355-2. Scheduled Maintenance
5
Maintenance and Care
You can customize settings in the setup display as follows:
Ta bItemExplanation
Scheduled
SettingNotification can be switched on/off.
Time (months)
Displays the time or distance until main-
tenance is due.
Select this item to set the maintenance
period.
“Scheduled Due!” is displayed in red and
the wrench indicator light in the combina-
tion meter will be illuminated when the
remaining distance is less than 250 miles
or 500 km, or the remaining number of
days is less than 15 (whichever comes
first).
Distance
(mile or km)
Reset
Resets the time and distance to the initial
values.
Once the system turns on, it needs to be
reset whenever carrying out mainte-
nance.
Tire Rotation
SettingNotification can be switched on/off.
Distance
(mile or km)
Displays the distance until tire rotation
is due.
Select this item to set the tire rotation
distance.
“Tire Rotation Due!” is displayed in red
and the wrench indicator light in the
combination meter will be illuminated
when the remaining distance is less
than 250 miles or 500 km.
Reset
Resets the remaining distance to the
initial value.
Once the system turns on, it needs to
be reset whenever r otating the tires.

4365-2. Scheduled Maintenance
YARIS SEDAN_OM_OM99S50z_(U)
Oil Change
Setting Inter-
val
Oil replacement period can be selected
from the flexible setting or fixed setting,
or it can be set to non-display.
The flexible setting is available only in the
United States and Puerto Rico. Once
engine oil flexible maintenance is
selected, the vehicle calculates the
remaining oil life based on the engine
operating conditions. The vehicle lets you
know when an oil change is due by illumi-
nating the wrench indicator light in the
combination meter. Toyota Genuine
Motor Oil or equivalent are required to
achieve optimum performance.
Distance (mile
or km)
(Displays only
in fixed set-
ting)
Displays the distance until the oil replace-
ment is due.
Select this item to set the oil replacement
distance.
“Oil Change Due!” is displayed in red and
the wrench indicator light in the combina-
tion meter will be illuminated when the
remaining distance is less than 250 miles
or 500 km.
Oil life (%)
(Displays only
in flexible set-
ting)
Displays the engine oil life until the oil
replacement is due.
“Oil Change Due!” is displayed in red and
the wrench indicator light in the combina-
tion meter will be illuminated when the
remaining oil life distance is less than
250 miles (500 km), or remaining days
are less than 15 (whichever comes first).
Reset
In flexible setting:
Resets the remaining oil life to 100%.
In fixed setting:
Resets the remaining distance to the ini-
tial value.
Once the Flexible Oil Maintenance Set-
ting is selected, the system must be reset
whenever replacing the engine oil.
Ta bItemExplanation

YARIS SEDAN_OM_OM99S50z_(U)
4435-3. Owner Maintenance
5
Maintenance and Care
After replacing the engine oil, have a repair shop such as your Toyota
dealer perform the initialization (engine oil data resetting) o f the
recorded value. If the value recorded by the computer is not in itialized,
the wrench indicator light may not turn off or it may turn on e arlier than
normal.
● This procedure is intended for vehicles with the engine oil fle xible mainte-
nance setting selected.
● The initialization (engine oil data resetting) of the recorded value can be per-
formed using the following procedure:
Switch the ignition OFF.
Vehicle Engine Control U nit Reset Procedure
Switch the ignition ON with the selec-
tor pressed, and press and hold the
selector for about 5 seconds until the
master warning light flashes.
After the master warning light
flashes for several seconds, the ini-
tialization is completed.
1
2
3
Selector