display VAUXHALL COMBO 2015 User Guide

Instruments and controls73
Control indicator in the roof
console
Airbag deactivation 3 45, 3 74.
Generic warning 9 illuminates yellow.
Depending on model variant, control
indicator 9 may illuminate
independently or in conjunction with
Æ , t , Z or r .
If 9 illuminates together with I; stop
engine immediately and seek the
assistance of a workshop.
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 80.
9 also illuminates if the fuel cut-off
switch is triggered, or if a fault is
detected in the engine oil pressure
sensor. Consult a workshop.
Fuel cut-off system 3 86.
Turn signal 2 or 3 flashes green.
Flashes
A turn signal or the hazard warning
flashers are activated.
Rapid flashing: failure of a turn signal
light or associated fuse, failure of turn signal light on trailer.
Bulb replacement 3 133, Fuses
3 139.
Turn signals 3 91.Seat belt reminder
Seat belt reminder for frontseats
X for driver's seat and/or front
passenger seat illuminates or flashes
red.
Illuminates
When the ignition has been switched
on, control indicator X illuminates
briefly if driver's seat belt and/or front
passenger seat belt is not engaged. A
warning chime also sounds for a few
seconds.
Flashes
During driving X will flash and a
warning chime will sound for
90 seconds until the front seat belts
are fastened.
Fastening the seat belt 3 39.

76Instruments and controlsTransmission
s illuminates red.
Illuminates when a fault is present in
the transmission.
A warning message may also appear
in the Driver Information Centre
3 80 in conjunction with a warning
chime.
Continued driving is possible,
provided the vehicle is driven with
care and anticipation.
Have the cause of the fault remedied
by a workshop as soon as possible.
Manual transmission automated
3 110.
Upshift [ or Ò illuminates in the Driver
Information Centre 3 80 when
gearshifting is recommended to
improve fuel economy.
Hill start assist Z illuminates yellow.Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
If the control indicator does not
extinguish after a few seconds, or if it illuminates while driving, there is a
fault in the Hill start assist. Seek the
assistance of a workshop to have the
fault remedied.
The Electronic Stability Program
(ESP) control indicator x may also
illuminate 3 76 in conjunction with
Z .
Depending on model variant, 9 will
illuminate as an alternative if control
indicator Z is not present.
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 80.
Generic warning 9 3 73.
Hill start assist 3 115.
Ultrasonic parking assist
r illuminates yellow.
Fault in system
orFault due to sensors that are dirty or
covered by ice or snow
or
Interference due to external sources
of ultrasound. Once the source of interference is removed, the system
will operate normally.
Have the cause of the fault in the
system remedied by a workshop.
Control indicator 9 will illuminate as
an alternative if control indicator r
is not present. Depending on version,
a warning message may also be
displayed in the Driver Information
Centre 3 80.
Generic warning 9 3 73.
Ultrasonic parking assist 3 118.
Electronic Stability
Program
R illuminates or flashes yellow.

Instruments and controls77
FlashesThe system is actively engaged.
Engine output may be reduced and
the vehicle may be braked
automatically to a small degree.
Illuminates
A fault in the system is present.
Continued driving is possible. Driving
stability, however, may deteriorate
depending on road surface
conditions.
Have the cause of the fault remedied
by a workshop.
Electronic Stability Program (ESP)
3 116, Traction control system/Anti-
Slip Regulator (ASR) 3 115.
Engine coolant
temperature
$ illuminates red.
Illuminates for a few seconds after the ignition is switched on.
If control indicator $ illuminates, the
coolant temperature is too high.
Depending on version, a warningmessage may also be displayed in
the Driver Information Centre 3 80.
Seek the assistance of a workshop.Caution
If engine coolant temperature is
too high, stop vehicle, switch off
the ignition. Danger to engine.
Check coolant level.
If the control indicator remains on, seek the assistance of your
workshop.
Engine coolant temperature gauge
3 70.
Preheating ! illuminates yellow.
Preheating is activated. Only
activates when outside temperature
is low.
Diesel particle filter
% illuminates yellow.
The diesel particle filter requires
cleaning.
Continue driving until %
extinguishes. If possible, do not allow engine speed to drop below
2000 rpm.
Illuminates The diesel particle filter is full. Start
cleaning process as soon as
possible.
Diesel particle filter 3 108, Stop-start
system 3 105.
Tyre pressure monitoring
system
w illuminates or flashes.
Illuminates
Tyre pressure loss. Stop immediately and check tyre pressure.
Control indicator w illuminates
together with a warning chime and, in
vehicles with Multifunction version of
the Driver Information Centre, a

78Instruments and controls
corresponding message also
appears when a puncture or severely
under-inflated tyre is detected.
Flashes
Fault in system. After a delay the
control indicator illuminates
continuously. Consult a workshop.
Control indicator w illuminates and
(depending on version) a
corresponding message appears in
the Driver Information Centre when a tyre without a pressure sensor ismounted (e.g. spare wheel).
Tyre pressure monitoring system
3 145.
Engine oil pressure
I illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.Illuminates when the engine is
runningCaution
Engine lubrication may be
interrupted. This may result in
damage to the engine and/or
locking of the drive wheels.
1. Depress clutch.
2. Select neutral gear (or move selector lever to N).
3. Move out of the flow of traffic as quickly as possible without
impeding other vehicles.
4. Switch off ignition.
9 Warning
When the engine is off,
considerably more force is needed
to brake and steer. During an
Autostop the brake servo unit will still be operational.
Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engage
unexpectedly.
Check oil level before seeking the
assistance of a workshop 3 128.
Change engine oil Diesel engines with dieselparticle filter
I flashes red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
The engine oil life monitor lets you know when to change the oil. Control
indicator I will flash to indicate that
engine oil life has been diminished
and the oil needs changing.
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 80.
Based on driving conditions, the
interval at which an oil change will be indicated can vary considerably.

Instruments and controls79
Depending on model variant, I may
flash in the following ways:
■ for 1 minute every 2 hours, or
■ for 3 minute cycles with I off for
intervals of 5 seconds.
The warning will be repeated every
time the engine is started, until the engine oil is changed and the service
display is reset. Seek the assistance
of a workshop.
Service display 3 70.
Low engine oil level S illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
If the control indicator does not
extinguish after a few seconds, or if it illuminates while driving, the engine
oil level is insufficient.
Check oil level before seeking the assistance of a workshop 3 128.Low fuel
$ illuminates or flashes yellow.
Illuminates for a few seconds after the ignition is switched on.
Illuminates Level in fuel tank is too low. Refuel
immediately 3 121.
Never run the tank dry. Catalytic converter 3 108.
Flashes
Fault in fuel system.
Have the cause of the fault remedied
by a workshop.
Fuel gauge 3 68.
Drain fuel filter
U illuminates yellow.
Illuminates when the ignition is
switched on and goes out shortly after
the engine starts.Illuminates when the engine is
running
Indicates the presence of water in the
diesel. Seek the assistance of a
workshop immediately.
Immobiliser d illuminates yellow.
Fault in the immobiliser system. The
engine cannot be started.
Stop-start system
Æ illuminates yellow.
A fault is present in the system.
Have the cause of the fault remedied
by a workshop.
Control indicator 9 will illuminate as
an alternative if control indicator Æ is
not present. Depending on version, a warning message may also be
displayed in the Driver Information
Centre 3 80.
Generic warning 9 3 73.
Stop-start system 3 105.

80Instruments and controlsExterior light8 illuminates green.
The exterior lights are on 3 89.
Exterior light failure
µ illuminates yellow.
One or more of the exterior lights is
faulty 3 133.
Control indicator 9 will illuminate as
an alternative if control indicator µ is
not present. Depending on version, a warning message may also be
displayed in the Driver Information
Centre 3 80.
Generic warning 9 3 73.
High beam C illuminates blue.
Illuminated when high beam is on and
during headlight flash 3 89.
Fog light > illuminates green.
The front fog lights are on 3 91.Rear fog light
r illuminates yellow.
The rear fog light is on 3 92.
Cruise control
m illuminates green.
The system is on.
Cruise control 3 117.
Door open
( illuminates red.
A door or the tailgate is open.Information displays
Driver Information Centre
The Driver Information Centre is
located in the instrument cluster
between the speedometer and
tachometer. Two versions are
available; a Standard version

Instruments and controls81
and a Multifunction version with
further adjustable settings.
Some of the displayed functions differ
when the vehicle is being driven or at a standstill. Some options are onlyavailable when the vehicle is being
driven.
Depending on variant, the following
items appear in the display:
■ Odometer, trip odometer 3 68
■ Clock 3 64
■ Outside temperature 3 64
■ Headlight range adjustment 3 90
■ Transmission display 3 110
■ Stop-start system indicator 3 105
■ Vehicle messages 3 86
■ Trip computer 3 87
Selecting menus and options
The menus and options can be
selected via the buttons on the
instrument panel.Press the SETq button:
■ once to access the settings menu
■ press again to access a menu option and submenu options
■ after changes have been made, briefly press again to confirm a
value and automatically return to
the previous display screen
Alternatively, press and hold the
SET q button to return to the
previous display screen without
saving changes to the current menu
option.
Notice
The settings menu is exited
automatically after a delay. Only
changes already confirmed by
briefly pressing the SETq button
are stored.

82Instruments and controls
Press the R button to scroll up the
screen and the menu options or to
increase the displayed value. Press
and hold to increase value rapidly
(press again to stop on the required
value).
Press the S button to scroll down the
screen and the menu options or to
decrease the displayed value. Press
and hold to decrease value rapidly (press again to stop on the requiredvalue).
Settings menu options -
Standard version The settings menu contains the
following options:
■ ILLU
■ SPEEd
■ HOUR
■ UNIT
■ bUZZ
■ BAG P
■ DRL
ILLU (Brightness of interior lighting)
When driving at night with the low
beam on, adjust the brightness of the
vehicle's interior lighting (e.g.
instrument panel, climate control display).
SPEEd (Speed limit warning chime)
Activate or deactivate the speed limit
warning chime or change the speed
limit. Speeds between 20 and
125 mph can be stored.
When activated, the driver is alerted
with a warning chime when the set
speed limit is exceeded.After accessing this menu option,
activate or deactivate the function
(set to On or Off) and confirm.
Press the SETq button when
activated ( On) to access the current
set speed. Adjust as required and
confirm.
Warning chimes 3 86.
HOUR (Setting the clock)
Adjust the hours setting (flashing
value) and confirm. Adjust minutes
setting (flashing value) and confirm.
Clock 3 64.
UNIT (Unit of measurement)
Set the unit of measurement to km or
miles .
bUZZ (Warning chime volume)
Adjust the volume of warning chimes
and confirm. 8 volume levels are
available.
A chime is also sounded every time
the SET q, R or S button is pressed.
Warning chimes 3 86.

Instruments and controls83
BAG P (Passenger front and side
airbags activation/deactivation)
Activate the front passenger airbags
if an adult is occupying the front
passenger seat. Deactivate airbags
when a child restraint system is
installed on this seat.9 Danger
Risk of fatal injury for a child using
a child restraint system on a seat
with activated front passenger
airbag.
Risk of fatal injury for an adult
person on a seat with deactivated
front passenger airbag.
After accessing this menu option,
activate or deactivate the airbags
( BAG P On or BAG P Off ) and
confirm; a confirmation message
appears in the display. Select YES (to
confirm changes) or No (to cancel
changes).
Airbag deactivation 3 45.
DRL (Daytime running lights)
Activate the daytime running lights to
increase visibility of the vehicle during
daylight (set to On). Deactivate when
not required (set to Off).
Daytime running lights 3 90.
Settings menu options -
Multifunction version
The settings menu contains the
following options:
■ Lighting
■ Speed beep
■ Trip B data
■ Set time
■ Set date
■ Radio info
■ Autoclose
■ Unit of measurement
■ Language
■ Warning volume
■ Button volume
■ Seat belt buzzer
■ Service
■ Passenger airbag■Daytime running lights
■ Exit menu
LIGHTING (Brightness of interior
lighting)
When driving at night with the low
beam on, adjust the brightness of the
vehicle's interior lighting (e.g.
instrument panel, climate control display).
It is also possible to adjust the
brightness using the R or S buttons
without accessing the settings menu.
SPEED BEEP (Speed limit warning chime)
Activate or deactivate the speed limit
warning chime or change the speed
limit. Speeds between 20 and
125 mph can be stored.
When activated, the driver is alerted
with a warning chime when the set
speed limit is exceeded.
After accessing this menu option,
activate or deactivate the function
(set to On or Off) and confirm.

84Instruments and controls
Press the SETq button when
activated ( On) to access the current
set speed. Adjust as required and
confirm.
Warning chimes 3 86.
TRIP B DATA
Activate or deactivate the second trip
computer (set to On or Off).
Trip B records average consumption,
distance travelled, average speed
and travel time (driving time). The
measurement can be restarted at any time. Trip computer 3 87.
SET TIME (Setting the clock and
clock mode)
After accessing this menu option, it is possible to either set the time or
change the clock mode between 12
hour and 24 hour clock.
Select Time and confirm. Adjust the
hours setting (flashing value) and confirm. Adjust minutes setting
(flashing value) and confirm.
Select Mode and confirm. Select
12h or 24h and confirm.
Clock 3 64.SET DATE
Adjust the year setting (flashing
value) and confirm. Adjust month
setting (flashing value) and confirm.
Adjust the day setting (flashing value)
and confirm.
RADIO INFO (Display audio and
radio information)
Activate radio info (set to On) to
display audio and radio information (e.g. station frequency, RDS
messages, track number). Deactivate
when not required (set to Off).
AUTOCLOSE (Automatic central
locking when driving)
Activate the autoclose feature (set to
On ) to automatically lock the doors
when vehicle speed exceeds
12 mph. Deactivate when not
required (set to Off).
UNIT OF MEASUREMENT (for
Distance, Fuel consumption and
Temperature)
After accessing this menu option, it is possible to set the unit of
measurement for distance, fuel
consumption and temperature.Select Distance and confirm. Set the
unit of measurement to km or mi
(miles) and confirm.
Select Consumption and confirm.
When the Distance unit is set to km, it
is possible to set the unit of
measurement for fuel consumption to either l/100km or km/l . When the
Distance unit is set to mi (miles), fuel
consumption is shown in mpg.
Select Temperature and confirm. Set
the unit of measurement to °C or °F
and confirm.
LANGUAGE
Languages selectable include:
English, German, French, Italian,
Portuguese, Spanish, Dutch, Polish and Turkish. Select desired language
and confirm.
WARNING VOLUME (Warning chime volume)
Adjust the volume of warning chimes
and confirm. 8 volume levels are
available.
Warning chimes 3 86.