lock VAUXHALL COMBO D 2017 Workshop Manual

Vehicle care153Instrument panel fuse box
The fuse box is located behind a
cover on the lower part of the
instrument panel, on the driver's side.
No.CircuitF12Right low beamF13Left low beam/Headlight range
adjustmentF31Fusebox relays/Body control
unit relaysF32Courtesy lightsF36Diagnostic connector/Climate
control system/Infotainment
system/Tyre pressure moni‐
toring system/Alarm sirenF37Instrument panel/Braking
systemF38Central locking systemF43Windscreen washer systemF47Power windowsF48Power windowsF49Exterior mirrors/Infotainment
system/Parking assist/Tyre
pressure monitoring system/
Instrument illumination/Rain
sensor

Vehicle care159Wheel covers must not impair brake
cooling.9 Warning
Use of unsuitable tyres or wheel
covers could lead to sudden
pressure loss and thereby
accidents.
Tyre chains
Tyre chains are only permitted on the
front wheels.
Always use fine mesh chains that add no more than 10 mm to the tyre tread
and the inboard sides (including chain lock).
Do not exceed 30 mph when tyre
chains are fitted.9 Warning
Damage may lead to tyre blowout.
Tyre repair kit
Minor damage to the tyre tread can be
repaired with the tyre repair kit.
Do not remove foreign bodies from
the tyres.
Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repairedwith the tyre repair kit.
9 Warning
Do not drive faster than 50 mph.
Do not use for a lengthy period.
Steering and handling may be
affected.
If you have a flat tyre:
Apply the parking brake and engage
first or reverse gear.
The tyre repair kit may be located
under the front seat, in the glovebox,
or on the right side of the load
compartment behind a cover.
1. Take the tyre repair kit from the vehicle.
2. Remove the compressor.
3. Set the compressor upright near the tyre.
4. Unscrew valve cap from defective
tyre.

Vehicle care161
If tyre pressure is more than
1.8 bar , set it to the correct value.
Repeat the procedure until there
is no more loss of pressure.
If the tyre pressure has fallen
below 1.8 bar, the vehicle must
not be used. Seek the assistance
of a workshop.
15. Stow away tyre repair kit in load compartment.
Notice
The driving characteristics of the
repaired tyre are severely affected,
therefore have this tyre replaced.
If unusual noise is heard or the
compressor becomes hot, turn
compressor off and allow to cool.
Note the expiry date of the kit. After
this date its sealing capability is no
longer guaranteed. Pay attention to
storage information on sealant
bottle.
Replace the used sealant bottle.
Dispose of the bottle as prescribed
by applicable laws.
The compressor and sealant can be used from approx. -20 °C.
Replacing the sealant canister
To replace the sealant canister: 1. Disconnect the compressor air hose.2. Turn the canister anticlockwise to lift it out.
3. Insert the new canister and turn it clockwise.
4. Connect the compressor air hose to the canister and fit the flexible
filler tube into its allocated space.
Wheel changing
Some vehicles are equipped with a
tyre repair kit instead of a spare wheel 3 159.
Make the following preparations and
observe the following information:
● Park the vehicle on a level, firm and non-skid surface. The front
wheels must be in the straight- ahead position.
● Apply the parking brake and engage first or reverse gear.
● Remove the spare wheel 3 163.
● Never change more than one wheel at once.
● Use the jack only to change wheels in case of puncture, not
for seasonal winter or summer
tyre change.

166Vehicle care● A discharged vehicle battery canalready freeze at a temperature
of 0 °C. Defrost the frozen battery before connecting jump leads.
● Wear eye protection and protective clothing when
handling a vehicle battery.
● Use a booster battery with the same voltage (12 Volts). Its
capacity (Ah) must not be much
less than that of the discharged
vehicle battery.
● Use jump leads with insulated terminals and a cross section of
at least 16 mm 2
(25 mm 2
for
diesel engines).
● Do not disconnect the discharged
battery from the vehicle.
● Switch off all unnecessary electrical consumers.
● Do not lean over the vehicle battery during jump starting.
● Do not allow the terminals of one
lead to touch those of the other
lead.● The vehicles must not come into contact with each other during
the jump starting process.
● Apply the parking brake, transmission in neutral.
Lead connection order:
1. Connect the red lead to the positive terminal of the booster
battery.
2. Connect the other end of the red lead to the positive terminal of the
discharged vehicle battery.
3. Connect the black lead to the negative terminal of the booster
battery.
4. Connect the other end of the black
lead to a vehicle grounding point,
such as the engine block or an
engine mounting bolt. Connect as far away from the discharged
vehicle battery as possible,
however at least 60 cm.
Route the leads so that they cannot
catch on rotating parts in the engine
compartment.
To start the engine: 1. Start the engine of the vehicle providing the jump.
2. After five minutes, start the other engine. Start attempts should be
made for no longer than
15 seconds at an interval of
one minute.
3. Allow both engines to idle for approx. three minutes with the
leads connected.

Vehicle care1674. Switch on electrical consumers(e.g. headlights, heated rear
window) of the vehicle receiving
the jump start.
5. Reverse above sequence exactly when removing leads.Towing
Towing the vehicle
Release the cap by carefully lifting
with a screwdriver. To prevent
damage, it is recommended to place
a cloth between the screwdriver and
the frame.
The towing eye is stowed with the vehicle tools 3 154.
Screw in the towing eye as far as it will
go until it stops in a horizontal
position.
Attach a tow rope – or better still a tow
rod – to the towing eye.
Caution
The towing eye must only be used for towing and not for recovering
the vehicle.
Switch on ignition to release steering
wheel lock and to permit operation of
brake lights, horn and windscreen
wiper.
Transmission in neutral.
Notice
If neutral cannot be selected on
vehicles with manual transmission
automated (MTA), the vehicle must
only be towed with the drive wheels
raised off the ground.
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can
damage the vehicle.
When the engine is not running,
considerably more force is needed to
brake and steer.

168Vehicle careTo prevent the entry of exhaust gasesfrom the towing vehicle, switch on the
air recirculation 3 105 and close the
windows.
Seek the assistance of a workshop. After towing, unscrew the towing eye
and replace the cap.
Towing another vehicle
Insert a screwdriver in the slot at the
side of the cap. Release the cap by
carefully levering the screwdriver. To
prevent damage it is recommended to place a cloth between the screwdriver
and the frame.
The towing eye is stowed with the vehicle tools 3 154.
Screw in the towing eye as far as it will
go until it stops in a horizontal
position.
Attach a tow rope – or even better a tow bar – to the towing eye.
The towing eye must only be used for
towing and not for recovering a
vehicle.Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can
damage the vehicle.
After towing, unscrew the towing eye.
Insert cap.
Appearance care
Exterior care Locks
The locks are lubricated at the factory using a high quality lock cylinder
grease. Use de-icing agent only when absolutely necessary, as this has a
degreasing effect and impairs lock
function. After using a de-icing agent,
have the locks regreased by a
workshop.
WashingThe paintwork of your vehicle is
exposed to environmental influences.
Wash and wax your vehicle regularly.
When using automatic vehicle
washes, select a programme that
includes waxing.
Bird droppings, dead insects, resin,
pollen and the like should be cleaned
off immediately, as they contain
aggressive constituents which can
cause paint damage.

176Technical dataThe identification plate is located in
the engine compartment, attached to
the bulkhead.
Information on identification label:
1:type approval number2:vehicle Identification Number3:vehicle type identification
code4:permissible gross vehicle
weight rating in kg5:permissible gross train weight
in kg6:maximum permissible front
axle load in kg7:maximum permissible rear
axle load in kg8:engine type9-11:vehicle-specific or country-
specific data
Notice
The identification plate on your
vehicle may differ from the
illustration shown.
The combined total of front and rear
axle loads must not exceed the
permissible gross vehicle weight. For
example, if the front axle is bearing its
maximum permissible load, the rear
axle can only bear a load that is equal
to the gross vehicle weight minus the front axle load.
The technical data is determined in
accordance with European
Community standards. We reserve
the right to make modifications.
Specifications in the vehicle
documents always have priority over
those given in this manual.
Engine identification
The engine number is stamped on the
engine block.
The technical data tables show the
engine identifier code. Engine data
3 178.
To identify the respective engine,
refer to the engine power in the EEC
Certificate of Conformity provided
with your vehicle or other national
registration documents.

Customer information187● vehicle reactions in particulardriving situations (e.g. inflation ofan airbag, activation of the
stability regulation system)
● environmental conditions (e.g. temperature)
This data is exclusively technical and
helps identifying and correcting errors
as well as optimizing vehicle
functions.
Motion profiles indicating travelled
routes cannot be created with this
data.
If services are used (e.g. repair
works, service processes, warranty cases, quality assurance),
employees of the service network
(manufacturer included) are able to
read out this technical information
from the event and error data storage
modules applying special diagnostic
devices. If required, you will receive
further information at these
workshops. After an error has been
corrected, the data is deleted from the error storage module or it is
constantly overwritten.When using the vehicle, situations
may occur in which technical data
related to other information (accident
report, damages on the vehicle,
witness statements etc.) may be
associated with a specific person -
possibly, with the assistance of an
expert.
Additional functions contractually
agreed upon with the client (e.g.
vehicle location in emergency cases)
allow the transmission of particular vehicle data from the vehicle.
Radio Frequency
Identification (RFID)
RFID technology is used in some
vehicles for functions such as tyre
pressure monitoring and ignition
system security. It is also used in
connection with conveniences such
as radio remote controls for door
locking/unlocking and starting, and in-
vehicle transmitters for garage door
openers. RFID technology in
Vauxhall vehicles does not use or
record personal information or link
with any other Vauxhall system
containing personal information.

188IndexAAccessories and vehicle modifications .......................... 136
Adjustable air vents ...................108
Airbag activation ........................... 88
Airbag and belt tensioners ...........80
Airbag deactivation ..........51, 81, 88
Airbag label................................... 46 Airbag system .............................. 46
Air conditioning regular operation ................................ 109
Air conditioning system .............. 105
Air intake .................................... 109
Air vents...................................... 108
Alert .............................................. 93
Antilock brake system ................ 122
Antilock brake system (ABS) .......82
Anti-Slip Regulator (ASR) ...........124
Anti-theft locking system .............. 28
Appearance care ........................168
Armrest ......................................... 38
Ashtrays ....................................... 73 ASR (Anti-Slip Regulator) ...........124
Audible warning chimes................ 93
Autoclose ...................................... 88
Automatic fuel cut-off ............94, 112
Automatic locking .........................88
Autostop ..................................... 113
AUX socket ................................... 72B
Battery discharge protection ......103
Belts.............................................. 43
Bonnet ....................................... 138
Brake and clutch fluid .................173
Brake assist ............................... 123
Brake fluid .................................. 142 Brake pad wear ............................ 82
Brakes ............................... 122, 141
Brake system ............................... 82
Breakdown.................................. 167
Bulb replacement ....................... 144
C Capacities .................................. 184
Car Pass ...................................... 20
Catalytic converter .....................117
Central locking system ................23
Centre high-mounted brake light 148
Change engine oil .......................86
Changing tyre and wheel size ...158
Charging system .......................... 81
Child locks ................................... 24
Child restraint installation locations ................................... 54
Child restraints.............................. 53
Child restraint systems ................53
Child safety system for rear windows .................................... 30
Chimes ......................................... 93

189Cigarette lighter ........................... 73
Climate control ............................. 15
Climate control systems .............104
Clock....................................... 70, 88
CNG............................................ 184
Collision damage repair ..............186
Control indicators.......................... 77
Control of the vehicle .................110
Controls ........................................ 68
Convex shape .............................. 29
Coolant and antifreeze ...............173
Cruise control ...................... 88, 126
Cupholders .................................. 59
D Danger, Warnings and Cautions ...4
Date .............................................. 88
Daytime running lights ............88, 98
Declaration of conformity ............186
Diesel particle filter ...............84, 116
Distance to next service ...............88
Door open .................................... 88
Doors ...................................... 25, 26
Drain fuel filter ............................. 87
Driver assistance systems ..........126
Driver Information Centre .............88
Driving characteristics and towing tips .............................. 134
Driving hints ................................ 110E
Eco mode (E).............................. 121
Electric adjustment ......................29
Electrical system......................... 150
Electronic climate control system 106
Electronic driving programmes ..121
Electronic Stability Control ..83, 125
Electronic Stability Control (ESC). 83
End-of-life vehicle recovery .......137
Engine compartment fuse box ...152
Engine coolant ........................... 140
Engine coolant temperature ........84
Engine coolant temperature gauge ....................................... 76
Engine data ............................... 178
Engine exhaust .......................... 116
Engine identification ...................176
Engine oil ...........139, 173, 177, 184
Engine oil pressure ......................85
ESC (Electronic Stability Control) 125
Event data recorders ..................186
Exit lighting ................................ 103
Extendable load compartment cover ................................... 61, 65
Exterior care .............................. 168
Exterior light ................................. 87
Exterior lighting ......................12, 97
Exterior mirrors ............................. 29F
Fault ........................................... 121
Fixed air vents ........................... 108
Fog light ....................................... 88
Fog lights ................................... 146
Folding front passenger seat ........37
Folding mirrors ............................. 29
Folding seats .......................... 39, 41
Front airbag system .....................50
Front fog lights ............................. 99
Front passenger seat Folding ...................................... 37
Table position ............................ 37
Front seats.................................... 35
Front storage ................................ 59
Front turn signal light ..................145
Fuel............................................. 130
Fuel consumption .........................88
Fuel consumption - CO 2-
Emissions ............................... 133
Fuel cut-off system .........79, 94, 112
Fuel for diesel engines ..............130
Fuel for natural gas operation ...130
Fuel for petrol engines ...............130
Fuel gauge ................................... 75
Fuel selector ................................ 75
Fuel system messages .........94, 112
Fuel tank ..................................... 184
Fuses ......................................... 150