torque VAUXHALL COMBO D 2017 Owner's Manual

112Driving and operatingDiesel engine: turn the key to position1 for preheating until control
indicator ! extinguishes.
Turn the key briefly to position 2 and
release.
Before restarting or to switch off the
engine, turn the key back to position
0.
Autostop During an Autostop, the engine is
restarted automatically by depressing
the clutch pedal.
Vehicles with manual transmission
automated (MTA): Shift to a forward
gear, release brake pedal or move
lever to +, – or R to enable an
automatic restart.
Stop-start system 3 113.Starting the vehicle at low
temperatures
The start of the engine without
additional heaters is possible down to -25 °С for diesel engines and -30 °C
for petrol engines. Required is an engine oil with the correct viscosity,
the correct fuel, performed services
and a sufficiently charged vehicle
battery.
Turbo engine warm-up Upon start-up, engine available
torque may be limited for a short time, especially when the engine
temperature is cold. The limitation is
to allow the lubrication system to fully
protect the engine.
Vehicle shutdown
Fuel cut-off system In the event of a collision of a certain
severity, the fuel system is cut-off and
the engine is switched off
automatically, for safety reasons.Control indicator 9 illuminates if the
fuel cut-off switch is triggered and, depending on version, a
corresponding warning message may also appear in the Driver InformationCentre 3 88.
Generic warning control indicator 9
3 79.
Notice
In addition, the vehicle is
automatically unlocked and the
hazard warning flashers and interior
lights are illuminated.
Turn the ignition key to position 0 to
prevent vehicle battery discharge and
seek the assistance of a workshop
immediately. Have the vehicle
checked for fuel leaks in the engine
compartment, beneath the vehicle
and near the fuel tank.
To reset the fuel cut-off system and
enable the vehicle to be driven:
1. Turn the ignition key to position 1 3 111.
2. Fully actuate the right turn signal light 3 99.
3. Deactivate the right turn signal light.

Vehicle care163the jacking point in a manner thatprevents it from slipping.
With the jack correctly aligned,
rotate until wheel is clear of the
ground.
5. Unscrew the wheel nuts. 6. Change the wheel. Spare wheel 3 163.
7. Screw on the wheel nuts.
8. Lower vehicle.
9. Install the wheel wrench ensuring that it locates securely and tighten
each nut in a crosswise
sequence. Tightening torque is
85 Nm (steel wheel) or 120 Nm
(alloy wheel).
10. Align the valve hole in the wheel cover with the tyre valve before
installing.
Install wheel nut caps.
11. Stow the replaced wheel 3 163
and the vehicle tools 3 154.
12. Check the tyre pressure of the installed tyre and the wheel nut
torque as soon as possible.
Have the defective tyre renewed or
repaired as soon as possible.
Spare wheel Some vehicles are equipped with atyre repair kit 3 159 instead of a spare
wheel.
If mounting a spare wheel which is
different from the other wheels, this
wheel might be classified as a
temporary spare wheel and the
corresponding speed limits apply,
even though no label indicates this.
Seek the assistance of a workshop to
check the applicable speed limit.Caution
The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres
could affect driveability. Have the defective tyre replaced as soon as
possible.
Depending on model variant, the
spare wheel is stored beneath the
floor or in the load compartment.
1. Attach the extension bar 2 to the
wheel wrench 1. Vehicle tools
3 154.

178Technical dataEngine dataSales designation1.41.41.4Engine identifier code1.4i1.4Turbo1.4CNGPiston displacement [cm3
]136813681368Engine power [kW]708888at rpm600050005000Torque [Nm]127206206at rpm450030003000Fuel typePetrolPetrolCompressed Natural Gas/PetrolOctane rating RON 1)recommended959595possible989898Gas––CNG1)
A country-specific label at the fuel filler flap can supersede the engine specific requirement.

Technical data179Sales designation1.3 Turbo2)1.3 Turbo3)1.6 Turbo 2)1.6 Turbo2)Engine identifier code1.3CDTI1.3CDTI1.6CDTI1.6CDTIPiston displacement [cm 3
]1248124815981598Engine power [kW]66706677at rpm4000350040004000Torque [Nm]200200290 / 200 4)290at rpm1500150015001500Fuel typeDieselDieselDieselDiesel2)
Euro 5+.
3) Euro 6.
4) Manual transmission / Manual transmission automated.Sales designation1.6 Turbo 5)2.0 TurboEngine identifier code1.6CDTI2.0CDTIPiston displacement [cm 3
]15981956Engine power [kW]70/74/77/88 6)99at rpm3500 - 40003500

180Technical dataSales designation1.6 Turbo5)2.0 TurboEngine identifier code1.6CDTI2.0CDTITorque [Nm]280 - 320320at rpm1500 - 17501500Fuel typeDieselDiesel5)
Euro 6.
6) Depending on output code.