ESP VAUXHALL CORSA 2014.5 Infotainment system

148CD PlayerCD PlayerGeneral information...................148
Usage ........................................ 149General information
With the CD player you can play
standard commercial CDs with a
diameter of 12 cm.Caution
Under no circumstances place
DVDs, single-CDs with a diameter
of 8 cm or shaped CDs in the audio
player.
You must not put any stickers on
CDs. These discs can get jammed
in the CD drive and ruin the drive.
An expensive replacement of the
device will then be necessary.
â–  The format of the CD must be ISO 9660 Level 1, Level 2 or
JOLIET. All other formats cannot be played back reliably.
â–  Audio CDs with copy protection, which are not in compliance with
the audio CD standard, may not
play correctly or not at all.
â–  You can also use the Infotainment system to play CDs containing MP3
music data and Mixed Mode CDs.
â–  Self-recorded CD-Rs and CD-RWs
are more vulnerable to mishandling
than prerecorded CDs. Correct
handling, especially in the case of
self-recorded CD-Rs and CD-RWs, must be ensured. See below.
â–  Self-recorded CD-Rs and CD-RWs
may not play correctly or not at all.
In such cases it is not the
equipment that is at fault.
â–  Avoid leaving fingerprints when you
change CDs.
â–  Put CDs back in their sleeves immediately after removing them
from the CD player in order to
protect them from damage and dirt.
â–  Dirt and liquids on CDs can smear the lens of the CD player inside the
device and cause faults.
â–  Protect CDs from heat and direct sunlight.
â–  The following restrictions apply for data stored on an MP3 CD:
When naming albums and tracks,
umlauts or special characters
should not be included.

Introduction161
If required, select the Bluetooth menu
item to display the respective menu.
If Bluetoothâ„¢ has been deactivated,
proceed as follows:
1. Select the Bluetooth menu item.
If Bluetoothâ„¢ has been activated,
the remaining menu items will
appear on the display.
2. Select the Bluetooth PIN menu
item.
3. Enter a random Bluetoothâ„¢ PIN and confirm it with OK.
For safety reasons, a randomly
selected PIN code of at least four digits should be used.
4. Ensure that the Bluetoothâ„¢ function of the mobile telephone
has been activated and set to
"visible".
5. Select the Start searching menu
item.
During the search process for
Bluetoothâ„¢ devices, the word
Searching... is displayed.
When the search process has
ended, the Bluetoothâ„¢ devices
are listed in the Found devices
menu.
6. Select the required mobile telephone.
While the connection is being
created, the message The
connection will be established...
appears on the display.
"Please enter the Bluetooth PIN"
or a similar request appears on
the display of the mobile
telephone.
7. Using the keypad on the mobile telephone, enter the same
Bluetoothâ„¢ PIN as for the
Infotainment system and confirm
it with OK.
The message "Add device to
known devices?", or a similar

Introduction163
The message "Device found:
UHP" appears on the display of
the mobile telephone.
3. Start the mobile telephone's connection function (see theoperating instructions for the
mobile telephone).
4. Enter the Bluetooth PIN in the
Infotainment system).
5. Enter the "Bluetooth PIN" on the mobile telephone.
The Bluetoothâ„¢ connection has been created between the mobile
telephone and the Infotainment
system.
Freespeech
A telephone connection is active.
Move the thumbwheel.
A context menu is opened. Activate
Freespeech . The sound is sent to the
car's loudspeakers.Emergency call9 Warning
Connection setup cannot be
guaranteed in all situations. For
this reason you should not rely
exclusively on a mobile phone
when a vitally important
communication (e. g. a medical
emergency) is concerned.
In some networks it may be
necessary for a valid SIM card to
be properly inserted in the mobile
phone.
9 Warning
Bear in mind that you can make
and receive calls with the mobile
phone, if it is in a service area with
a sufficiently strong signal. Under
certain circumstances emergency
calls cannot be made on all mobile
phone networks; it is possible that
they cannot be made when certain network services and/or telephone
functions are active. You can
enquire about this with the local
network operators.
The emergency call number can
differ depending on the region and country. Please enquire
beforehand about the correct
emergency call number for the
relevant region.
Making emergency calls
Dial the emergency number (e.g.
112).
The connection to the emergency call centre is created.
Answer if the service staff ask you
about the emergency.
Ending emergency calls Select the Hang-up menu item.
Or:
Press the p key.

Introduction167
You can now enter numbers using thethumbwheel.
In the display footer, select the figures required.
The signal tones are now sent.
Freespeech
With a mobile telephone connected
via Bluetoothâ„¢, with this function you
can turn off the hands-free function
3 160.Mobile phones and CB
radio equipment
Installation instructions and operating guidelines The vehicle specific installation
instructions and the operating
guidelines of the mobile phone and
handsfree manufacturer must be observed when installing and
operating a mobile telephone. Failure to do so could invalidate the vehicle
type approval (EU directive 95/54/
EC).
Recommendations for fault-free
operation:
â–  Professionally installed exterior antenna to obtain the maximum
range possible,
â–  Maximum transmission power 10 watts,
â–  Installation of the phone in a suitable spot, consider relevant
Note in the Owner's manual,
chapter Airbag system .Seek advice on predetermined
installation points for the external
antenna or equipment holder and
ways of using devices with a
transmission power exceeding 10
watts.
Use of a handsfree attachment
without external antenna with mobile
telephone standards GSM
900/1800/1900 and UMTS is only
permitted if the maximum
transmission power of the mobile
telephone is 2 watts for GSM 900 or
1 watt for the other types.
For reasons of safety, do not use the
phone while driving. Even use of a handsfree set can be a distraction
while driving.9 Warning
Operation of radio equipment and
mobile telephones which fail to
meet above mentioned mobile
telephone standards is only
permitted using an antenna
located outside of the vehicle.

170Voice recognition
Ending the dialogue
There are various ways to deactivate
the speech recognition system and
end the dialogue:
â–  By pressing q
â–  Time-outs: if nothing has been input for a certain period of time
The speech recognition system is
also interrupted by an incoming call.
Operation With the aid of the speech recognition
system, the mobile telephone can be
operated very comfortably using the
voice input function. Simply activate
the speech recognition system and
say the desired command. Once the
command has been input, you will be
led through the dialogue with the
corresponding questions and
messages in order to reach the
required action.
Say the commands and digits in a
normal voice, without any artificial
pauses between the numbers.
Recognition is most successful when
you pause for at least half a second
after every three to five numbers.The Infotainment system
simultaneously reacts to commands with voice messages and displays.
Main commands After the speech recognition system
has been activated, you will hear a
short sound, which is a signal to
inform you that the speech
recognition system is waiting for an
input.
The following commands are
available:
â–  " Call "
â–  " Redial "
â–  " Save "
â–  " Delete "
â–  " Phonebook "
â–  " Help "
â–  " Cancel "
Detailed description of these
commands see below.
"Call"
Using this command, you can input a telephone number which has beensaved in the phone book under aname (voice tag) or which is to be
used to create a connection. After this
command, the following commands
are available:
â–  " Number ": The connection is
created using the number entered.
â–  " Name ": The connection is created
using the voice tag."Number"
After this command has been given,
you will be asked to enter the number. The Infotainment system repeats the
recognised numbers. You can then input additional numbers or the
following commands:
â–  " Call " or " Accept ": The inputs are
accepted.
â–  " Change ": The last block of
numbers has been deleted.
â–  " Delete ": The complete input has
been deleted.
â–  " Help ": The dialogue is ended and
all commands available in this
context are listed.
â–  " Plus ": A plus is placed before the
number for foreign calls.

Voice recognition171
â–  "Additional digits ": Additional digits
are being added.
â–  " Cancel :" Ending the dialling
process. After the request for a
correction, all blocks of numbers previously entered are repeated
with the exception of the last block. If all inputs have been deleted, you
are once again asked to input a
telephone number.
If there is a voice pause of more than one second between the individual
numbers, the Infotainment system
assumes that the process of inputting
the block of numbers has ended and
repeats the block of numbers.
In order to make a foreign call, you
can say the word " Plus" (+) in front of
the number. The plus allows you to
make a call from that country without
knowing the foreign dialling code for
the country in question. Then say the
country code.
The country code corresponds to the
conventional format, i. e. 49 for
Germany, 44 for Great Britain, etc.The "0" must be left out of the local
network code (dialling code) except in Italy.
Example of a dialogue between the
user and voice output to dial a
telephone number:
User: " Call"
Voice output: " Name or Number? "
User: " Number "
Voice output: " The number, please! "
User: " Plus Four Nine "
Voice output repeats: " Plus Four
Nine "
User: " Seven Three One "
Voice output repeats: " Seven Three
One "
User: " One One Nine Nine "
Voice output repeats: " One One Nine
Nine "
User: " Change "
Voice output repeats the blocks of
numbers previously input: " Plus Four
Nine – Seven Three One "
User: " One One Nine One "Voice output repeats: " One One Nine
One "
User: " Call"
Voice output: " The number is being
dialled ""Name"
Using this command, you can select a telephone number under a name
(voice tag).
If the system recognises a name entry already available, it is shown on the
display. The symbol q representing
a voice tag appears to the right of the
name. The connection is created using the voice tag.
"Redial"
Using the " Redial" command, the
number most recently dialled can be
redialled.
"Save"
Using this command, you can save a
telephone number under a voice tag.
Additionally the previously input voice tag in the phone book can be
included.

174IndexAAccepting calls............................ 164Activating speech recognition .....169
B Bluetooth connection ..................160
C Call lists ...................................... 164
Changing the language ..............169
D Dialling ........................................ 164
DTMF.......................................... 164
E Emergency call ........................... 163
Ending calls ................................ 164
Entering PIN codes..................... 164
Entries with several numbers .....164
F
Filtering ....................................... 164
Freespeech................................. 160 Functions during a call ...............164
G
General information ....................158
H Hang-up ...................................... 164L
Lists ............................................ 164
M Making telephone calls ...............164
Micro off ...................................... 164
Mobile phones and CB radio equipment .............................. 167
N
Name .......................................... 169
Number ....................................... 169
O Operation .................................... 164
P Phone book ................................ 164
R
Redialling .................................... 164
Refusing calls ............................. 164
S Selecting telephone numbers .....164
Speech recognition .....................169
Steering wheel remote control ....158
T
Telephone numbers ...................164