ECO VAUXHALL CORSA F 2020 Manual Online

Vehicle care193Appearance care
Exterior care LocksThe locks are lubricated at the factoryusing a high quality lock cylinder
grease. Use a de-icing agent only
when absolutely necessary, as this
has a degreasing effect and impairs
lock function. After using a de-icing
agent, have the locks regreased by a
workshop.
Washing
The paintwork of your vehicle is
exposed to environmental influences.
Bird droppings, dead insects, resin,
pollen and the like should be cleaned
off immediately, as they contain
aggressive constituents which can cause paint damage.
If using a vehicle wash, comply with
the vehicle wash manufacturer's
instructions. The windscreen wiperand rear window wiper must beswitched off. Remove antenna and
external accessories such as roof
racks etc.
If you wash your vehicle by hand,
make sure that the insides of the
wheel housings are also thoroughly
rinsed out.
Clean edges and folds on opened
doors and the bonnet as well as the
areas they cover.
Clean bright metal mouldings with a
cleaning solution approved for
aluminium to avoid damages.Caution
Always use a cleaning agent with
a pH value of 4 to 9.
Do not use cleaning agents on hot surfaces.
Do not clean the engine compartmentwith a steam-jet or high-pressure jet
cleaner.
Thoroughly rinse and leather-off the vehicle. Rinse leather frequently. Use
separate leathers for painted and
glass surfaces: remnants of wax on
the windows will impair vision.
Have the door hinges of all doors
greased by a workshop.
Exterior lights
Headlight and other light covers are
made of plastic. Do not use any
abrasive or caustic agents, do not use an ice scraper, and do not clean them
dry.
Polishing and waxing
Polishing is necessary only if the paint
has become dull or if solid deposits
have become attached to it.
Plastic body parts must not be treated with wax or polishing agents.
Windows and wiper blades Switch off wipers before handling in
their areas.
Use a soft lint-free cloth or chamois
leather together with window cleaner
and insect remover.
When cleaning the rear window from
inside, always wipe in parallel to the
heating element to prevent damage.

Vehicle care195Caution
Close Velcro fasteners as open
Velcro fasteners on clothing could damage seat upholstery.
The same applies to clothing with
sharp-edged objects, like zips or
belts or studded jeans.
Plastic and rubber parts
Plastic and rubber parts can be
cleaned with the same cleaner as
used to clean the body. Use interior cleaner if necessary. Do not use any
other agent. Avoid solvents and petrol in particular. Do not use high-
pressure jet cleaners.
Floor mats
9 Warning
If a floor mat has the wrong size or
is not properly installed, it can
interfere with the accelerator pedal
and/or brake pedal, what can
cause unintended acceleration
and/or increased stopping
distance which can cause a crash and injury.
Use the following guidelines for
proper floor mat usage.
● The original equipment floor mats
were designed for your vehicle. If the floor mats need replacing, it
is recommended that certified
floor mats be purchased. Always
check that the floor mats do not
interfere with the pedals.
● Use the floor mat with the correct
side up. Do not turn it over.
● Do not place anything on top of the driver side floor mat.
● Use only a single floor mat on the
driver side.
● Do not place one floor mat on top
of another.
Inserting and removing the floor
mats
The driver side floor mat is held in
place by two retainers.
To install the floor mat:
1. Move the seat backwards as far as possible.
2. Align slots in the mat with theretainers, as shown.
3. Push the mat to the floor.
Removing 1. Move the seat backwards as far as possible.
2. Remove the mat.

196Service and maintenanceService and
maintenanceGeneral information ...................196
Service information ..................196
Recommended fluids, lubricants
and parts .................................... 199
Recommended fluids and lubricants ................................ 199General information
Service information In order to ensure economical and
safe vehicle operation and to
maintain the value of your vehicle, it
is of vital importance that all
maintenance work is carried out at the proper intervals as specified.
The detailed, up-to-date service
schedule for your vehicle is available
at the workshop.
Severe operating conditions exist if one or more of the following
circumstances occur frequently: Cold
starting, stop and go operation, e.g.
for taxis and police vehicles, trailer
operation, mountain driving, driving
on poor and sandy road surfaces,
increased air pollution, presence of
airborne sand and high dust content,
driving at high altitude and large
variations of temperature.
Under these severe operating
conditions, certain service work may
be required more frequently than the
regular service interval indicated inthe service display. Contact a
workshop for customised service
schedules.
Service display 3 64.

198Service and maintenanceConfirmations
Confirmation of service is recorded in the Service and warranty booklet. The date and mileage is completed with the stamp
and signature of the servicing workshop.
Make sure that the Service and warranty booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle.

Service and maintenance199Recommended fluids,
lubricants and parts
Recommended fluids and lubricants
Only use products that meet the
recommended specifications.9 Warning
Operating materials are
hazardous and could be
poisonous. Handle with care. Pay
attention to information given on
the containers.
Engine oil
Engine oil is identified by its quality
and its viscosity. Quality is more
important than viscosity when
selecting which engine oil to use. The oil quality ensures e.g. engine
cleanliness, wear protection and oil
aging control, whereas viscosity
grade gives information on the oil's
thickness over a temperature range.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 203.
Topping up engine oilCaution
In case of any spilled oil, wipe it up and dispose it properly.
Engine oils of different manufacturersand brands can be mixed as long as
they comply with the required engine
oil quality and viscosity.
Use of engine oils for all petrol
engines with only ACEA quality is
prohibited, since it can cause engine
damage under certain operating
conditions.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 203.
Additional engine oil additives
The use of additional engine oil
additives could cause damage and
invalidate the warranty.
Engine oil viscosity grades
The SAE viscosity grade gives
information of the thickness of the oil.
Multigrade oil is indicated by two
figures, e.g. SAE 5W-30. The first
figure, followed by a W, indicates the
low temperature viscosity and the
second figure the high temperature viscosity.
Select the appropriate viscosity grade depending on the minimum ambient
temperature 3 203.
All of the recommended viscosity
grades are suitable for high ambient
temperatures.
Coolant and antifreeze
Use only Lobrid antifreeze approved
for the vehicle. Consult a workshop.
The system is factory filled with
coolant designed for excellent
corrosion protection and frost
protection down to approx. -28 °C. In
cold regions with very low
temperatures the factory filled coolant
provides frost protection down to
approx. -37 °C. This concentration
should be maintained all year round.

Technical data201Technical dataVehicle identification..................201
Vehicle identification number ..201
Identification plate ...................201
Engine identification ................202
Vehicle data ............................... 203
Recommended fluids and lubricants ................................ 203
Engine data ............................. 205
Performance ............................ 206
Vehicle dimensions .................207
Capacities ................................ 208
Tyre pressures ........................ 209Vehicle identification
Vehicle identificationnumber
The Vehicle Identification Number
may be embossed on the instrument
panel, visible through the windscreen, or in the engine compartment on the
right body panel.
Identification plate
The identification plate is located on
the front left or right door frame.

Technical data203Vehicle data
Recommended fluids and lubricants
Required engine oil quality Country groups 3 196
Countries included in country groups 1 to 3EB2FA
EB2ADT
EB2ADTD
EB2ADTS
EP6FADTXD
DV5RC
DV5RD
DV5RE
EP6FDTM
EB2DT
EC5F
DW10FC
DV6D
DV6FD
DV6FE
Vauxhall Original engine oilB71 2010 / B71 2312B71 2312
Engine EC5F: B71 2290, B71 2296 or B71 300 may also be used.
Countries included in country group 4
all enginesVauxhall Original engine oilB71 2302 / B71 2297
Engine EC5F: B71 2296 or B71 300 may also be used.

Technical data205Engine dataEngine identifier codeEB2FAEB2ADTDEB2ADTSDV5RDSales designation1.21.2 T1.2 T1.5 DPiston displacement [cm3
]1199119911991499Engine power [kW]55749675at rpm5750550055003500Torque [Nm]118205230250at rpm2750175017501750Fuel typePetrolPetrolPetrolDieselOctane rating RON 1)2)recommended959595–possible989898–possible919191–Additional fuel type––––1)
A country specific label at the fuel filler flap can supersede the engine specific requirement.
2) In certain countries, the use of a particular fuel, e.g. a specific octane rating, may be required to ensure proper engine operation.

Technical data207Vehicle dimensionsLength [mm]4060Width without exterior mirrors [mm]1745Width with two exterior mirrors folded [mm]1791Width with two exterior mirrors [mm]1960Height (without antenna) [mm]1432Length of load compartment floor [mm]680Length of load compartment with folded second row [mm]1385Load compartment width between wheel arches [mm]1018Load compartment width at seat belt height [mm]833Wheelbase [mm]2538Turning circle diameter [m]10.32

210Customer informationCustomer
informationCustomer information ................210
Declaration of conformity .........210
REACH .................................... 212
Software acknowledgement ....212
Software update ......................214
Registered trademarks ............214
Vehicle data recording and pri‐
vacy ........................................... 215
Event data recorders ...............215
Radio Frequency Identification (RFID) ..................................... 218Customer information
Declaration of conformity
Radio transmission systems
This vehicle has systems that
transmit and / or receive radio waves
subject to Directive 2014/53/EU. The
manufacturers of the systems listed
below declare conformity with
Directive 2014/53/EU. The full text of
the EU declaration of conformity for each system is available at the
following internet address:
www.opel.com/conformity.
Importer is
Opel / Vauxhall, Bahnhofsplatz,
65423 Ruesselsheim am Main,
Germany.
Infotainment system Multimedia Navi
Pro / Multimedia Navi
Continental Automotive Czech
Republic s.r.o
Prumyslová 1851, 250 01 Brandys
nad Labem, Czech RepublicOperation
frequency
(MHz)Maximum
output (dBm)BT2402.0 -
2480.04.1Wifi2412.0 -
2462.016.7
Infotainment system Radio
Hangsheng technology GmbH
Bouchéstr. 12, 12435 Berlin,
Germany
Operation frequency:
2402.0 - 2480.0 MHz
Maximum output: 4 dBm
Infotainment system Multimedia
Robert Bosch Car Multimedia GmbH
Robert-Bosch-Strasse 200, 31139
Hildesheim, Germany
Operation frequency:
2400.0 - 2483.5 MHz
Maximum output: 4 dBm
Wireless charger
Continental Automotive GmbH