checking oil VOLKSWAGEN CORRADO 1993 User Guide
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1993, Model line: CORRADO, Model: VOLKSWAGEN CORRADO 1993Pages: 920, PDF Size: 6.92 MB
Page 324 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 10)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
necessary. Check purity of oil and adjust oil level as follows.
4) If amount drained is 3 ounces or more, oil level is okay.
Fill with same amount drained, using new oil. If amount drained is
less than 3 ounces, pour in 3 ounces of new refrigerant oil.
COMPONENT REFRIGERANT OIL CAPACITIES (ATSUGI ROTARY VANE)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ....................................... 1.0-1.7
Evaporator ...................................... 1.5-2.5
Receiver-Drier .................................. 0.5-0.8
Refrigerant Lines (1) ........................... 1.0-1.7
(1) - Add only if a refrigerant oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ BOSCH
6-CYLINDER
1) Before checking and adjusting oil level, operate
compressor at engine idle speed, and set controls at maximum cooling
and high blower motor speed for 20-30 minutes to return oil to
compressor.
2) Stop engine and discharge refrigerant. See SERVICING
PRECAUTIONS. Remove refrigerant oil level inspection plug on side of
compressor. Oil should be at lower lip of threaded hole. If oil level
is low, add new refrigerant oil as necessary. Replace inspection plug
and tighten to 10-12 ft. lbs. (14-16 N.m).
CALSONIC
V5 5-CYLINDER & V6 6-CYLINDER
Infiniti & Nissan
1) Before checking and adjusting oil level, operate engine at
1200 RPM. Set controls at maximum cooling and high blower motor speed
for 10 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant. See SERVICING
PRECAUTIONS. Measure the amount of oil drained/discharged into
refrigerant recovery/recycling equipment.
3) Remove compressor from vehicle. Drain compressor oil from
compressor drain plug and measure oil amount. Add this amount to
amount drained in step 2), to obtain total amount drained.
4) Fill compressor with total amount drained, using new oil.
If any major components of the system were also replaced, determine
the amount of additional oil needed. See appropriate COMPONENT
REFRIGERANT OIL CAPACITIES table for specified amount.
COMPONENT REFRIGERANT OIL CAPACITIES (CALSONIC V5)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Page 325 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 11)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
Component Ounces
Condenser ........................................ 1.0-1.7
Evaporator ....................................... 1.5-2.5
Receiver-Drier ................................... 0.5-0.8
Refrigerant Lines (1) ............................ 1.0-1.7
(1) - Add only if a refrigerant oil leak is indicated.ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄCOMPONENT REFRIGERANT OIL CAPACITIES (CALSONIC V6)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................ 2.5
Evaporator ........................................... 2.5
Receiver-Drier ....................................... 0.2
Refrigerant Lines (1) ................................ 1.0
(1) - Add only if a refrigerant oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Subaru
1) Before checking and adjusting oil level, operate engine at
1000-1500 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Drain compressor oil from
compressor drain plug and measure oil amount.
3) Fill compressor with total amount drained, using new oil.
If any major components of the system were also replaced, determine
the amount of additional oil needed. See appropriate SUBARU COMPONENT
REFRIGERANT OIL CAPACITIES table for specified amount.
SUBARU COMPONENT REFRIGERANT OIL CAPACITIES (LEGACY)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Compressor ........................................... 2.4
Condenser ............................................ 1.7
Evaporator ........................................... 2.4
Refrigerant Lines (1) ................................ 1.7
(1) - Add only if a refrigerant oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄSUBARU COMPONENT REFRIGERANT OIL CAPACITIES (SVX)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Compressor ........................................... 2.4
Condenser ............................................ 1.7
Page 326 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 12)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
Evaporator ........................................... 2.4
Refrigerant Lines (1) ................................ 1.7
(1) - Add only if a refrigerant oil leak is indicated.ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ DIESEL KIKI
ROTARY VANE
1) Before checking and adjusting oil level, operate engine at
800-1000 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
measure amount of oil drained.
3) If amount drained is less than 3 ounces (1.7 ounces on Geo
Storm), conduct leak tests at system connections. Repair or replace
faulty parts as necessary.
4) If amount drained is more 3 ounces (1.7 ounces on Geo
Storm), oil level is okay. Fill compressor with same amount drained,
using new oil. If amount drained is less than 3 ounces (1.7 ounces on
Geo Storm), pour in 3 (1.7) ounces of new refrigerant oil.
5) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
CAPACITIES (DIESEL KIKI ROTARY VANE) table.
COMPONENT REFRIGERANT OIL CAPACITIES (DIESEL KIKI ROTARY VANE)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................... 1.7
Evaporator .............................................. 1.0
Receiver-Drier .......................................... 1.0
Refrigerant Lines ....................................... 0.3
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 5 & 6-CYLINDER
1) Before checking and adjusting oil level, operate engine at
800-1000 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
measure amount of oil drained.
3) If amount drained is less than 3 ounces, conduct leak
tests at system connections. Repair or replace faulty parts as
necessary.
4) If amount drained is more 3 ounces, oil level is okay.
Fill compressor with same amount drained, using new oil.
5) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
Page 327 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 13)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
CAPACITIES (DIESEL KIKI 5 & 6-CYLINDER) table.
COMPONENT REFRIGERANT OIL CAPACITIES (DIESEL KIKI 5 & 6-CYLINDER)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser .................................................. 1.0
Evaporator ................................................. 1.7
Receiver-Drier ............................................. 1.0
Refrigerant Lines .......................................... 0.3
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ FORD
FX-15 10-CYLINDER
1) Slowly discharge system. See SERVICING PRECAUTIONS. Remove
A/C compressor. Drain compressor oil from suction and discharge ports.
Measure amount drained and discard oil.
2) If amount drained from removed (old) compressor is between
3 and 5 ounces, add drained amount of new refrigerant oil into the NEW
compressor through suction port.
3) If amount drained is less than 3 ounces, add 3 ounces to
the NEW compressor. If amount drained is more than 5 ounces, add 5
ounces. Use new "O" rings on refrigerant lines. Install A/C
compressor. Evacuate and recharge system. Perform leak test.
4) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
CAPACITIES (FX-15 10-CYLINDER) table.
COMPONENT REFRIGERANT OIL CAPACITIES (FX-15 10-CYLINDER)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................ 1.0
Evaporator ........................................... 3.0
Receiver-Drier ................................... (1) 2.0
Refrigerant Lines ................................ (2) 1.0
(1) - On Hyundai Sonata and Mazda Navajo, drain oil from old
receiver-drier. Add amount drained to amount specified.
(2) - Add only if a large oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ HADSYS
7-CYLINDER
Honda (Accord)
1) Discharge system. See SERVICING PRECAUTIONS. Remove
compressor from vehicle. Drain all oil from NEW compressor and fill
compressor with 4 ounces of clean refrigerant oil.
Page 328 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 14)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
2) Add one ounce of refrigerant oil when replacing
evaporator. Add1/2 ounce when replacing condenser. When replacing
receiver-drier or hoses, add 1/3 ounce per component replaced.
HARRISON
R4 4-CYLINDER
1) Before checking and adjusting oil level, operate engine at
800-1000 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
measure amount of oil drained.
3) If amount drained is less than one ounce, conduct leak
tests at system connections. Repair or replace faulty parts as
necessary. Fill compressor with 2 ounces, using new refrigerant oil.
4) If amount drained is more one ounce, oil level is okay.
Fill compressor with same amount drained, using new oil.
5) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
CAPACITIES (HARRISON R4 4-CYLINDER) table.
COMPONENT REFRIGERANT OIL CAPACITIES (HARRISON R4 4-CYLINDER)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................... 1.0
Evaporator .............................................. 1.7
Receiver-Drier .......................................... 1.0
Refrigerant Lines ....................................... 0.3
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ V5 5-CYLINDER
1) If system is operable, run A/C system for several minutes
to stabilize system. Turn off engine. Discharge system and remove
compressor. See SERVICING PRECAUTIONS. Remove drain plug and measure
oil.
2) If one ounce or more is drained, add same amount. If less
than one ounce is drained, add 2 ounces of new refrigerant oil to
compressor.
3) If condenser is replaced, add one ounce. Add 3.5 ounces if
accumulator is replaced. If evaporator is replaced or if a large
refrigerant leak occurred, add 3 ounces of new refrigerant oil.
HITACHI
6-CYLINDER
1) Before checking and adjusting oil level, operate
compressor at 1000-1500 engine RPM, and set controls at maximum
Page 329 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 15)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
cooling and high blower motor speed for about 10 minutes to return oil
to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Drain oil from compressor
through suction port. Measure amount of oil drained.
3) If amount drained is 2.4 ounces or more, fill with same
amount using new oil. If amount drained is less than 2.4 ounces, fill
with 2.4 ounces. Install compressor and recharge.
4) If A/C components are replaced, add refrigerant oil to
system. Add 1.7 ounces if condenser is replaced. Add 2.4 ounces if
evaporator is replaced. Oil does not need to be added if receiver-
drier is replaced. Add 1.7 ounces of refrigerant oil only if a
refrigerant oil leak is indicated.
MATSUSHITA
ROTARY VANE
Geo (Prizm)
1) If system is operable, run A/C system for several minutes
to stabilize system. Turn off engine. Discharge system and remove
compressor. See SERVICING PRECAUTIONS. Remove drain plug and measure
oil.
2) If one ounce or more is drained, add same amount. If less
than one ounce is drained, add 2 ounces of new refrigerant oil to
compressor.
3) If condenser is replaced, add one ounce. Add 3.5 ounces if
receiver-drier is replaced. If evaporator is replaced or if a large
refrigerant leak occurred, add 3 ounces of new refrigerant oil.
Toyota
Discharge system. See SERVICING PRECAUTIONS. Remove
compressor from vehicle. Drain oil from compressor through inlet and
outlet ports. Fill compressor with 3.4-4.1 ounces of oil through
suction port. Add 0.7 ounces if receiver-drier was replaced. When
replacing condenser or evaporator, add 1.4-1.7 ounces of refrigerant
oil.
NIPPONDENSO
ROTARY VANE
1) Before checking and adjusting oil level, operate
compressor at engine idle speed, and set controls at maximum cooling
and high blower motor speed for 20-30 minutes to return oil to
compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Drain compressor oil through
compressor intake and discharge ports. Measure amount drained.
3) Fill compressor with same amount as drained, plus one
ounce. When replacing condenser, add one ounce. When replacing
evaporator, add 1 1/2 ounces. When replacing receiver-drier, add 1/3
Page 330 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 16)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
ounce of new refrigerant oil.
6 & 10-CYLINDER
NOTE: Porsche and Suzuki compressor oil checking procedures are
not available from manufacturer.
Acura & Honda
1) Discharge system. See SERVICING PRECAUTIONS. Remove
compressor from vehicle. Drain all oil from NEW compressor and fill
compressor with 3-4 ounces of clean refrigerant oil.
2) On Accord, add 5/6 ounce of refrigerant oil when replacing
evaporator. Add 1/3 ounce when replacing condenser. When replacing
receiver-drier or hoses, add 1/3 ounce per component replaced.
3) On Legend, add 2 ounces of refrigerant oil when replacing
evaporator. Add one ounce when replacing condenser. When replacing
receiver-drier or hoses, add 1/3 ounce per component replaced.
4) On Integra, add one ounce of refrigerant oil when
replacing evaporator. When replacing condenser, receiver-drier or
hoses, add 1/3 ounce per component replaced.
5) On Vigor, add 1/2 ounce of refrigerant oil when replacing
evaporator. Add 2/3 ounce when replacing condenser. When replacing
receiver-drier or hoses, add 1/3 ounce per component replaced.
Chrysler Corp. (Colt Vista/Summit Wagon)
Add 2 ounces of refrigerant oil when replacing evaporator.
Add one ounce when replacing condenser. When replacing receiver-drier
or hoses, add 1/3 ounce per component replaced.
Ford Motor Co.
On Capri, add 2-3 ounces when replacing compressor. Add one
ounce of refrigerant oil when replacing condenser or evaporator. When
replacing receiver-drier, add 1/2 ounce. On Festiva, drain and measure
oil from receiver-drier. Add the amount drained plus one ounce. Add
one ounce when replacing condenser. Add 3 ounces of refrigerant oil
when replacing evaporator.
Geo, Hyundai & Mazda
Add one ounce of refrigerant oil when replacing condenser.
Add 1-1 1/2 ounce when replacing evaporator. When replacing receiver-
drier or hoses, add 1/3 ounce per component replaced.
Lexus & Toyota
The use of refrigerant recovery/recycling is recommended by
manufacturer. After refrigerant recovery process is completed, the
amount of compressor oil removed must be measured and the same amount
added to A/C system. Add 1 1/2 ounces of refrigerant oil when
replacing condenser. Add 1 1/2 ounces when replacing evaporator. When
replacing receiver-drier or hoses, add1/2 ounce per component
replaced.
Mercedes-Benz
Page 331 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 17)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
Add 2/3 ounce of refrigerant oil when replacing condenser.
Add 1 1/3 ounces when replacing evaporator. When replacing receiver-
drier or hoses, add 1/3 ounce per component replaced. If A/C system
line has broken (sudden discharge), add1 1/3 ounces of refrigerant
oil.
NOTE: On Mercedes-Benz vehicles with rear A/C, add 2/3 ounce of
refrigerant oil when replacing rear condenser. When
replacing rear A/C lines, add 1/3 ounce per line replaced.
Mitsubishi
1) On Eclipse, add 2/3 ounce of refrigerant oil when
replacing condenser. Add one ounce when replacing evaporator. When
replacing receiver-drier or hoses, add 1/3 ounce per component
replaced.
2) On Expo/Expo LRV and Montero, add one ounce of refrigerant
oil when replacing condenser. Add 2 ounces when replacing evaporator.
When replacing receiver-drier or hoses, add 1/3 ounce per component
replaced.
Volkswagen (Fox)
1) The use of refrigerant recovery/recycling is recommended
by manufacturer. After refrigerant recovery process is completed, the
amount of compressor oil removed must be measured and the same amount
added to A/C system.
2) Add 1 1/2 ounce of refrigerant oil when replacing
evaporator. When replacing condenser, add 1 1/3 ounce of refrigerant
oil. Add one ounce of refrigerant oil when replacing receiver-drier (1
1/2 ounces if relief valve on receiver-drier has burst).
PANASONIC
ROTARY VANE
Mazda
Add 1 1/3 ounce of refrigerant oil when replacing condenser
(1/2 ounce on MX-6 and 626). Add 2 ounces when replacing evaporator.
When replacing receiver-drier or hoses, add 1/3 ounce of refrigerant
oil.
SANDEN
SCROLL
Chrysler/Mitsubishi
1) On Colt, Galant, Mirage, Pickup, Ram-50 and Summit, add
1/2 ounce of refrigerant oil when replacing condenser. Add 1 1/2
ounces when replacing evaporator. When replacing receiver-drier or
hoses, add 1/3 ounce per component replaced.
2) On Stealth and 3000GT, add 1/2 ounce of refrigerant oil
when replacing condenser. Add 2 ounces when replacing evaporator. When
replacing receiver-drier or low-pressure hose, add 1/3 ounce per
Page 332 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 18)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
component replaced.
Honda
1) Discharge system. See SERVICING PRECAUTIONS. Remove
compressor from vehicle. Drain all oil from NEW compressor and fill
compressor with 4 ounces of clean refrigerant oil.
2) On Civic and Civic Del Sol, add 1 1/2 ounce of refrigerant
oil when replacing evaporator. Add 2/3 ounce when replacing condenser.
When replacing receiver-drier or hoses, add 1/3 ounce per component
replaced.
3) On Prelude, add one ounce of refrigerant oil when
replacing evaporator. When replacing other A/C components, add 1/3
ounce per component replaced (including hoses).
Hyundai
Add 1 1/2 ounces of refrigerant oil when replacing
evaporator. Add one ounce when replacing condenser. When replacing
receiver-drier, add 1/3 ounce of refrigerant oil.
5-CYLINDER
Mazda
Add one ounce of refrigerant oil when replacing condenser.
Add 1 2/3 ounce when replacing evaporator. When replacing receiver-
drier, add 1/2 ounce of refrigerant oil.
NOTE: Saab and Volvo (Sanden 5 or 7-cylinder) compressor oil
checking procedures are not available from manufacturer.
7-CYLINDER
Hyundai & Mitsubishi (Excel & Precis)
1) Before checking and adjusting oil level, operate
compressor at engine idle speed, and set controls at maximum cooling
and high blower motor speed for 20-30 minutes to return oil to
compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
drain oil. Measure amount of oil drained. Install drain plug with new
"O" ring.
3) If amount drained is 2.3 ounces or more, fill compressor
with same amount using new oil. If amount drained is less than 2.3
ounces, fill with 2.3 ounces. Install filler plug. Install compressor
and recharge system.
COMPONENT REFRIGERANT OIL CAPACITIES (SANDEN 7-CYLINDER)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................ 1.0
Evaporator ............................................. 3
Receiver-Drier ......................................... 1
Page 333 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 19)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PMÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Jaguar (XJS)
1) Operate engine at idle speed for 10 minutes, to return
refrigerant oil to compressor. Stop engine. Discharge refrigerant. See
SERVICING PRECAUTIONS. Clean area around compressor filler plug and
remove plug slowly.
2) Determine angle at which compressor is mounted. Insert
compressor dipstick diagonally until stop on dipstick contacts filler
plug surface. See Fig. 1. Remove dipstick and note oil fill level.
Each increment on dipstick represents one ounce of oil.
3) Determine amount of oil needed according to mounting
angle. See COMPRESSOR OIL CAPACITIES (JAGUAR XJS) table for specified
amount.
4) If necessary, correct compressor oil level. Install
compressor oil plug, and tighten it to 72-108 INCH lbs. (8-12 N.m).
Evacuate and recharge A/C system. Perform leak test.Fig. 1: Checking Jaguar XJS Compressor Oil Level (Sanden 7-Cylinder)
Courtesy of Jaguar Cars, Inc.
COMPRESSOR OIL CAPACITIES (JAGUAR XJS)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄMounting Angle (In Degrees) Oil Level In Increments
0 .................................................... 3-5
10 ................................................... 4-6
20 ................................................... 5-7
30 ................................................... 6-8
40 ................................................... 7-9
50 .................................................. 8-10
60 .................................................. 9-11
90 ................................................. 10-12
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Volkswagen
1) The use of refrigerant recovery/recycling is recommended